DLA DSCC-VID-V62 12641-2012 MICROCIRCUIT LINEAR LOW NOISE MICROPOWER 5 0 V PRECISION VOLTAGE REFERENCE MONOLITHIC SILICON.pdf

《DLA DSCC-VID-V62 12641-2012 MICROCIRCUIT LINEAR LOW NOISE MICROPOWER 5 0 V PRECISION VOLTAGE REFERENCE MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-VID-V62 12641-2012 MICROCIRCUIT LINEAR LOW NOISE MICROPOWER 5 0 V PRECISION VOLTAGE REFERENCE MONOLITHIC SILICON.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Phu H. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ Original date of dra

2、wing YY MM DD CHECKED BY Phu H. Nguyen TITLE MICROCIRCUIT, LINEAR, LOW NOISE, MICROPOWER 5.0 V PRECISION VOLTAGE REFERENCE, MONOLITHIC SILICON 12-10-09 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12641 REV PAGE 1 OF 7 AMSC N/A 5962-V006-13 Provided by IHSNot for Resale-,-,-DL

3、A LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12641 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low noise, micropower 5.0 V precision voltage reference microcircuit, with an operating temperature range of -55C to +

4、125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/12641 - 01 X B Drawing Device type Case outline Lead f

5、inish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 ADR293-EP Low noise, micropower 5.0 V precision voltage reference 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style

6、X 8 JEDEC MO-153-AA Thin Shrink Small Outline Package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Prov

7、ided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12641 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage . 18.0 V Output short circuit duration to GND . Indefinite Operating temperature range: . -55C to +125C Storage temperature rang

8、e . -65C to +150C Junction temperature range -65C to +150C Lead temperature (soldering, 60 sec) . 300C 1.4 Thermal characteristics. Thermal resistance Case outline JAJCUnit Case X 240 43 C/W 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Standard Outlin

9、es for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201.) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufact

10、urers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electri

11、cal characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams

12、. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only

13、, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Provided by IHSNot for Resale-,-,-DLA LAND AND M

14、ARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12641 REV PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Symbol Test conditions VS= 6.0 V, TA=25C unless otherwise specified Limits Unit Min Typ Max Output voltage (T Grade) VOUTIOUT= 0 mA 4.990 5.000 5.010 V Initial acc

15、uracy (T Grade) IOUT= 0 mA -10 +10 0.20 mV % Line regulation (T Grade) VOUT/VIN6.0 V to 15 V, IOUT= 0 mA 40 150 ppm/V Load regulation (T Grade) VOUT/ILOADVS= 6.0 V, IOUT= 0 mA to 5 mA 30 150 ppm/mA Long term stability VOUTAfter 1000 hours of operation 125C 50 ppm Voltage noise eN p-pf = 0.1 Hz to 10

16、 Hz 15 V p-p Voltage noise density eNf = 1 kHz 640 nV/Hz Test Symbol Test conditions VS= 6.0 V -25C TA +85C unless otherwise specified Limits Unit Min Typ Max Temperature coefficient (T Grade) TCVOUTIOUT= 0 mA 10 25 ppm/C Line regulation (T Grade) VOUT/VIN6.0 V to 15 V, IOUT= 0 mA 50 200 ppm/V Load

17、regulation (T Grade) VOUT/ILOADVS= 6.0 V, IOUT= 0 mA to 5 mA 30 200 ppm/mA Test Symbol Test conditions VS= 6.0 V -55C TA +125C unless otherwise specified Limits Unit Min Typ Max Temperature coefficient (T Grade) TCVOUTIOUT= 0 mA 10 30 ppm/C Line regulation (T Grade) VOUT/VIN6.0 V to 15 V, IOUT= 0 mA

18、 70 250 ppm/V Load regulation (T Grade) VOUT/ILOADVS= 6.0 V, IOUT= 0 mA to 5 mA 30 300 ppm/mA Supply current IS25C 11 15 15 20 A Thermal hysteresis (T Grade) VOUT-HYS157 ppm 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the

19、 specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. Provided by IHSNot for Resale-,-,-D

20、LA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12641 REV PAGE 5 Case X ebE E1D1 48 5AA1SEE DETAIL ASEATINGPLANEcL0-8DETAIL APIN 1IDENTIFIERDimensions Symbol Millimeters Symbol Millimeters Min Max Min Max A 1.20 E 4.30 4.50 A1 0.05 0.15 E1 6.40 BSC b 0.19 0.30 e 0.65 BSC

21、c 0.09 0.20 L 0.45 0.75 D 2.90 3.10 NOTES: 1. All linear dimensions are in millimeters. 2. Falls within JEDEC MO-153-AA. FIGURE 1. Case outline. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12641 REV PAGE 6 Case outline X Terminal num

22、ber Terminal symbol Terminal number Terminal symbol 1 NC 8 NC 2 VIN7 NC 3 NC 6 VOUT4 GND 5 NC FIGURE 2. Terminal connections. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12641 REV PAGE 7 4. VERIFICATION 4.1 Product assurance requirem

23、ents. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applica

24、ble. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classifie

25、d as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggest

26、ed source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandma

27、ritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Ordering Quantity Vendor part number V62/12641-01XB 24355 96 ADR293TRU-EP 1000 ADR293TRU-EP-R7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 24355 Analog Devices 1 Technology Way P.O. Box 9106 Norwood, MA 02062-9106 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS