DLA DSCC-VID-V62 06611 REV A-2013 MICROCIRCUIT DIGITAL-LINEAR CMOS DUAL PULSE-WIDTH-MODULATION CONTROL CIRCUIT MONOLITHIC SILICON.pdf

《DLA DSCC-VID-V62 06611 REV A-2013 MICROCIRCUIT DIGITAL-LINEAR CMOS DUAL PULSE-WIDTH-MODULATION CONTROL CIRCUIT MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-VID-V62 06611 REV A-2013 MICROCIRCUIT DIGITAL-LINEAR CMOS DUAL PULSE-WIDTH-MODULATION CONTROL CIRCUIT MONOLITHIC SILICON.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate to current MIL-PRF-38535 requirements. - PHN 13-12-11 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing

2、 REV PAGE REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL-LINEAR, CMOS, DUAL PULSE-WID

3、TH-MODULATION CONTROL CIRCUIT, MONOLITHIC SILICON YY-MM-DD 06-01-17 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06611 REV A PAGE 1 OF 11 AMSC N/A 5962-V021-14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENT

4、ER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance dual pulse-width-modulation control circuit microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor

5、Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/06611 - 01 X E Drawing Device type Case outline Lead finish number (See

6、 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 TL1451A-EP Dual pulse-width-modulation control circuit 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 16 JEDEC MS-012 Plastic

7、small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1.3 Absolute maximum ratings. 1/ Maximum sup

8、ply voltage (VCC) . 51 V Maximum amplifier input voltage (VI) 20 V Maximum collector output voltage (VO) . 51 V Maximum collector output current (IO) . 21 mA Maximum continuous power total dissipation: TA 25C 1088 mW TA= 70C 696 mW TA= 85C 566 mW TA= 125C 218 mW Derating factor above TA= 25C . 8.7 m

9、W/C Operating free-air temperature range -55C to +125C Storage temperature range (TSTG) . -65C to 150C 2/ Lead temperature soldering (1.6 mm (1/16 in) from case for 10 seconds) 260C _ 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are

10、stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Long-term high-temperature

11、 storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. See figure 1 for additional information on thermal derating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CEN

12、TER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 3 1.4 Recommended operating conditions. 1/ Supply voltage range (VCC) . 3.6 V to 50 V Amplifier input voltage range (VI) 1.05 V to 1.45 V Maximum collector output voltage (VO) . 50 V Maximum collector output curren

13、t (IO) . 20 mA Maximum current into feedback terminal 45 A Minimum feedback resistor (RF) 100 k Timing capacitor range (CT) 150 pF to 15000 pF Timing resistor range (RT) . 5.1 k to 100 k Oscillator frequency range 1 kHz to 500 kHz Operating free-air temperature range (TA) -55C to +125C FIGURE 1. Est

14、imated device life at elevated temperatures. 1/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE ID

15、ENT NO. 16236 DWG NO. V62/06611 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Associati

16、on, 3103 North 10th Street, Suite 240S, Arlington, VA 22201-2107). 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification

17、 (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4

18、, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 2. 3.5.2 Functional block diagram. The functional block diagram

19、shall be as shown in figure 3. 3.5.3 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.4 Timing waveforms and test circuit. The timing waveforms and test circuit shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

20、t license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VCCTemperature, TADevice type Limits Unit Min Max Reference Section Output voltage (REF) IO= 1 m

21、A, f = 200 kHz 6 V 25C 01 2.4 2.6 V -55C to +125C 2.35 2.65 Output voltage change with temperature f = 200 kHz 6 V 25C, -55C to +125C 4% 2/ Input voltage regulation f = 200 kHz 3.6 V to 40 V 25C 12.5 mV +125C 15 -55C 30 Output voltage regulation IO= 0.1 mA to 1 mA, f = 200 kHz 6 V 25C 7.5 mV +125C 1

22、4 -55C 20 Short-circuit output current VO= 0 V, f = 200 kHz 6 V 25C, -55C to +125C 3 30 mA Undervoltage Lockout Section Upper threshold voltage (VCC) f = 200 kHz 6 V 25C 01 2.72 TYP V +125C 1.7 TYP -55C 3.15 TYP Lower threshold voltage (VCC) f = 200 kHz 6 V 25C 2.6 TYP V +125C 1.65 TYP -55C 3.09 TYP

23、 Hysteresis (VCC) f = 200 kHz 6 V 25C 80 mV +125C 10 -55C 10 Reset threshold voltage (VCC) f = 200 kHz 6 V 25C 1.5 V +125C 0.95 -55C 1.5 Short-Circuit Protection Control Section Input threshold voltage (SCP) f = 200 kHz 6 V 25C 01 650 750 mV +125C 400 650 -55C 800 950 Standby voltage (SCP) f = 200 k

24、Hz 6 V 25C, -55C to +125C 140 230 mV Latched input voltage (SCP) f = 200 kHz 6 V 25C 120 mV +125C 120 -55C 120 Equivalent timing resistance f = 200 kHz 6 V 25C 170 TYP k Comparator threshold voltage (FEEDBACK) f = 200 kHz 6 V 25C 1.18 TYP V See footnotes at end of table. Provided by IHSNot for Resal

25、eNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions VCCTemperature, TADevice type Limits

26、Unit Min Max Oscillator Section Frequency CT= 330 pF, RT= 10 k, f = 200 kHz 6 V 25C 01 200 TYP kHz +125C 195 TYP -55C 193 TYP Standard deviation of frequency CT= 330 pF, RT= 10 k, f = 200 kHz 6 V 25C 2% Frequency change with voltage f = 200 kHz 3.6 V to 40 V 25C 1% +125C 1% -55C 3% Frequency change

27、with temperature f = 200 kHz 6 V 25C, -55C to +125C 10% 2/ Dead-Time Control Section Input bias current (DTC) f = 200 kHz 6 V 25C 01 1 A -55C to +125C 3 Latch mode (source) current (DTC) f = 200 kHz 6 V 25C, -55C to +125C -80 A Latched input voltage (DTC) f = 200 kHz 6 V 25C 2.3 V +125C 2.22 -55C 2.

28、28 Input threshold voltage at f = 10 kHz (DTC) Zero duty cycle 6 V 25C, -55C to +125C 2.25 2/ V Maximum duty cycle 1.2 2/ Error-Amplifier Section Input offset voltage VO(FEEDBACK) = 1.25 V, f = 200 kHz 6 V 25C 7 mV +125C 10 -55C 12 Input offset current VO(FEEDBACK) = 1.25 V, f = 200 kHz 6 V 25C 100

29、nA +125C 100 -55C 200 Input bias current VO(FEEDBACK) = 1.25 V, f = 200 kHz 6 V 25C 500 nA +125C 500 -55C 700 Common-mode input voltage range f = 200 kHz 3.6 V to 40 V 25C, -55C to +125C 1.05 to 1.45 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitte

30、d without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 7 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions VCCTemperature, TADevice type Limits Unit Min Max Error-Amplifier Section -

31、Continued. Open-loop voltage amplification RF= 200 k, f = 200 kHz 6 V 25C 01 70 dB +125C 70 -55C 64 Unity-gain bandwidth f = 200 kHz 6 V 25C 1.5 TYP MHz Common-mode rejection ratio f = 200 kHz 6 V 25C, -55C to +125C 60 dB Positive output voltage swing f = 200 kHz 6 V 25C, -55C to +125C 2 V Negative

32、output voltage swing f = 200 kHz 6 V 25C, -55C to +125C 1 V Output (sink) current (FEEDBACK) VID= -0.1 V, VO= 1.25 V, f = 200 kHz 6 V 25C 0.5 mA +125C 0.4 -55C 0.3 Output (source) current (FEEDBACK) VID= 0.1 V, VO= 1.25 V, f = 200 kHz 6 V 25C -45 A +125C -25 -55C -15 Output Section Collector off-sta

33、te current VO= 50 V, f = 200 kHz 6 V 25C, -55C to +125C 01 10 A Output saturation voltage f = 200 kHz 6 V 25C 2 V +125C 2.4 -55C 2.2 Short-circuit output current VO= 6 V, f = 200 kHz 6 V 25C 90 mA PWM Comparator Section Input threshold voltage at f = 10 kHz (FEEDBACK) Zero duty cycle 6 V 25C, -55C t

34、o +125C 01 2.25 2/ V Maximum duty cycle 1.2 2/ Total Device Standby supply current Off-state, f = 200 kHz 6 V 25C, -55C to +125C 1.8 mA Average supply current RT= 10 k, f = 200 kHz 6 V 25C, -55C to +125C 2.4 mA 1/ Testing and other quality control techniques are used to the extent deemed necessary t

35、o assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design

36、. 2/ These parameters are not production tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 8 Case X Dimensions Symbol Inches Millimeters Sym

37、bol Inches Millimeters Min Max Min Max Min Max Min Max A - 0.069 - 1.75 E 0.150 0.157 3.80 4.00 A1 0.004 0.010 0.10 0.25 E1 0.228 0.244 5.80 6.20 b 0.012 0.020 0.31 0.51 e 0.050 BSC 1.27 BSC c 0.007 0.010 0.17 0.25 L 0.016 0.050 0.40 1.27 D 0.386 0.394 9.80 10.00 NOTES: 1. All linear dimensions are

38、shown in inches (millimeters). Millimeters equivalents are given for general information only. 2. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0.15). 3. Falls within JEDEC MS-012 variation AC. FIGURE 2. Case outline. Provided by IHSNot for ResaleNo reproduction or net

39、working permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 9 FIGURE 3. Functional block diagram. Device type: 01 Case outline: X Terminal number Terminal symbol Terminal number Terminal symbol 1 CT 9 VCC2 RT

40、10 2OUT 3 1IN+ 11 2DTC 4 1IN- 12 2FEEDBACK 5 1FEEDBACK 13 2IN- 6 1DTC 14 2IN+ 7 1OUT 15 SCP 8 GND 16 REF FIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT

41、NO. 16236 DWG NO. V62/06611 REV A PAGE 10 NOTE: Protection enable time, tpe= (0.051 x 106x Cpe) in seconds. FIGURE 5. Timing waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SI

42、ZE A CODE IDENT NO. 16236 DWG NO. V62/06611 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrosta

43、tic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic dischar

44、ge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the

45、right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DL

46、A Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/06611-01XE 01295 TL1451AMDREP TL1451EPG4 1

47、/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-