DLA DSCC-DWG-89042 REV J-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW STRAIGHT THRU.pdf

《DLA DSCC-DWG-89042 REV J-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW STRAIGHT THRU.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-89042 REV J-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW STRAIGHT THRU.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Figure 1, made dimensional changes. TABLE III, added options up to 80 positions. Marking, changed marking requirements. 06/01/90 Richard Marbais B Figure 1, change .050 to a ref dimension. Add resistance to soldering heat test and add temperature range desig

2、nator table (TABLE IV). Add new designator to part number table. Change CAGE 22526 address. 10/03/92 Randy Larson C Figure 1, change positions A and B to 40, add dash numbers 24 and 25. Delete CAGE 91506 as source. 8/23/93 Randy Larson D Table II change C and D contact finish to D and E. 11/22/93 Ra

3、ndy Larson E Add contact finish designator C, table I define contact and termination area. Change CAGE 95238 address. 03/29/95 Randy Larson F Change CAGE 14933 to 037Z3. Replace cancelled MIL-Specs with industry replacements. Incorporated wrappost configurations into document. Editorial changes thro

4、ughout. 04/18/02 Robert Heber G Updating references and CAGE (8N187) Part or Identifying Numbers (PIN). Editorial changes throughout. 13 October 2010 Abdo Abdouni H Updating references and CAGE (8N187) Part or Identifying Numbers (PIN). 24 October 2011 Abdo Abdouni J Add option for selective plating

5、 to plating code “A”. 17 October 2012 Abdo Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV J G J G H G G H G PAGE 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Dave Leight Original date of dra

6、wing 30 Aug 1989 CHECKED BY TITLE Carl Dello-Stritto CONNECTORS, ELECTRICAL, UNSHROUDED HEADERS, PWB TERMINATION, .025, DOUBLE ROW, STRAIGHT THRU APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 89042 A 037Z3 REV J PAGE 1 OF 9 AMSC N/A 5935-E845-004 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHA

7、NGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV G PAGE 2 Inches mm .008 .010 .015 .045 .05

8、0 .100 .190 0.20 0.25 0.38 1.14 1.27 2.54 4.83 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified all tolerances are .005 (0.13 mm). 4. All undimensioned pictorial representations are for reference purposes only. 5. Plating transit

9、ion area, contact finish “D” only. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV J PAGE 3 TABLE I. Pin length.

10、1/ 2/ Dash number Dimension A contact area (mm) Dimension B Termination area (mm) Dimension C Overall length (mm) 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 .200 .230 .230 .230 .230 .230 .230 .230 .255 .285 .285 .318 .318 .318 .318 .318 .318 .400 .430 .500 .520 .540 .

11、610 .270 .770 (5.08) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (6.48) (7.24) (7.24) (8.08) (8.08) (8.08) (8.08) (8.08) (8.08) (10.16) (10.92) (12.70) (13.21) (13.72) (15.49) (6.77) (19.56) .110 .045 .095 .110 .150 .225 .285 .595 .120 .095 .230 .107 .120 .220 .318 .420 .520 .115 .120 .120 .318

12、 .120 .115 .400 .295 (2.79) (1.14) (2.41) (2.79) (3.81) (5.72) (7.24) (15.11) (3.05) (2.41) (5.84) (2.72) (3.05) (5.59) (8.08) (10.67) (13.21) (2.92) (3.05) (3.05) (8.08) (3.05) (2.92) (10.16) (7.42) .410 .375 .425 .440 .480 .555 .615 .925 .475 .480 .615 .525 .538 .638 .736 .838 .938 .615 .650 .720

13、.938 .760 .825 .770 1.165 (10.41) (9.52) (10.80) (11.18) (12.19) (14.10) (15.62) (23.50) (12.06) (12.19) (15.62) (13.34) (13.67) (16.21) (18.69) (21.29) (23.83) (15.62) (16.51) (18.29) (23.83) (19.30) (20.96) (19.56) (27.05) 1/ Dimensions are in inches. 2/ Metric equivalents are given for informatio

14、n. TABLE II. Plating. Plating Contact area “A” Termination area “B” A 1/ Gold Gold B Tin-lead plated Tin-lead C 1/ .200 inch(5.08 mm) min gold Tin-lead plated D Gold solder posts Tin-dipped 2/ E Tin-lead plated Solder dipped F 1/ .200 inch (5.08 mm) min gold Solder dipped 1/ Selective gold plating a

15、pplicable to contact pin lengths .230 inch (5.84 mm) and longer. Measured from tip of contact pin, remainder of contact post to be plated with nickel in accordance with SAE-AMS-QQ-N-290, class 2, 50 microinch (1.27 m) minimum. 2/ The use of pure tin is prohibited. Tin content used in connector mater

16、ials shall not exceed 97 percent, and an alloy material shall be chosen to inhibit the growth of tin whiskers. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 8904

17、2 REV G PAGE 4 TABLE III. Dimensions E. 1/ 2/ Number of positions Dimensions Number of positions Dimensions 02 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 .100 .200 .300 .400 .500 .600 .700 .800 .900 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000 (2.54) (5.08) (7.62)

18、(10.16) (12.70) (15.24) (17.78) (20.32) (22.86) (25.40) (27.94) (30.48) (33.02) (35.56) (38.10) (40.64) (43.18) (45.72) (48.26) (50.80) 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 2.100 2.200 2.300 2.400 2.500 2.600 2.700 2.800 2.900 3.000 3.100 3.200 3.300 3.400 3.500 3.600 3.700 3.

19、800 3.900 4.000 (53.34) (55.88) (58.42) (60.96) (63.50) (66.04) (68.58) (71.12) (73.66) (76.20) (78.74) (81.28) (83.82) (86.36) (88.90) (91.44) (93.98) (96.52) (99.06) (101.60) 1/ Dimensions are in inches. 2/ Metric equivalents are given for information. TABLE IV. Temperature range. PIN designator T

20、emperature range C Blank -40 to +105 M -55 to +125 H -65 to +220 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV H PAGE 5 REQUIREMENTS: Shall meet the re

21、quirements of drawing 86100. Dimensions and configuration: See figures 1, 3 and tables I, II, III. Temperature range: See table IV. Dielectric withstanding voltage: 1,000 volts rms (sea level). Current rating: 3 amperes continuous to 5 amperes maximum. Insulation resistance: 5,000 megohms. Resistanc

22、e to soldering heat: Only applicable for “H” temperature range (see table IV). Materials: Insulator: The insulator shall be one of the following types of plastic. All plastic material shall be rated V-0 in accordance with UL-94. a. Glass-or mineral-filled nylon in accordance with ASTM D4066. b. Glas

23、s filled thermoplastic in accordance with ASTM D5927 or MIL-M-24519. c. Thermoplastic polyphenylene sulfide type GST-40F in accordance with ASTM D4067. Contact: Three-fourth hard phosphor bronze in accordance with ASTM B139/B139M. Contact plating: Contact and termination plating shall be gold in acc

24、ordance with ASTM B488, type 3, code C, class 1.27 (50 microinch) or 100 microinches (2.54 m) minimum tin-lead in accordance with SAE-AMS-P-81728 over 50 microinches (1.27 m) minimum nickel in accordance with SAE-AMS-QQ-N-290, class 2. The “E” or “F” lead finish shall be hot solder dipped with SN60

25、or SN63 solder in accordance with IPC-J-STD-006 to meet the solderability requirements of MIL-STD-202, method 208. Selective plating: Selective gold contact plating is for contact pin lengths .230 inch (5.84 mm) and longer. The gold plating is measured from tip of contact pin to pin body and the pla

26、ting length shall be .200 inch (5.08 mm). The contact shall be plated with gold in accordance with ASTM B488, type 3, code C, class 1.27 (50 microinches) over 50 microinches (1.27 m) of nickel in accordance with SAE-AMS-QQ-N-290. Nickel plating shall extend over the entire length of the pin. The rec

27、ommended use of this finish is for mating with latch housings or PWB housings where the mating depth does not exceed .190 inches (4.83 mm). Solderless wrappost: The solderless wrappost termination shall be in accordance with figures 2 and 3. Interface: See drawings 86038, 86103, 92025, 92026, 92027,

28、 and 92028. Printed wiring board (PWB) hole size: .040 inch .003 inch (1.02 0.076 mm). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV G PAGE 6 Number E

29、length of wrapped connections Wire gage 30 (mm) Wire gage 28 (mm) Wire gage 26 (mm) Wire gage 24 (mm) Wire gage 22 (mm) Wire gage 20 (mm) Wire gage 18 (mm) 1 .185 (4.70) .219 (5.56) .226 (5.74) .258 (6.55) .303 (7.69) .327 (8.31) .391 (9.93) 2 .320 (8.13) .388 (9.85) .402 (10.21) .466 (11.83) .556 (

30、14.12) .604 (15.34) .732 (18.59) 3 .455 (11.56) .557 (14.15) .578 (14.68) .674 (14.43) .809 (20.55) .881 (.22.37) 1.073 (27.25) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 2. Wrappable length (typical connection). Provided by IHSNot for ResaleNo r

31、eproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV G PAGE 7 Inches mm .0012 .0015 .003 0.030 0.038 0.076 A (mm) B (mm) C (mm) Parallelism (mm) Straightness Inch/inch (mm) .025 (0.63) nomina

32、l .022 (0.56) min .025 (0.63) nominal .022 (0.56) min .0355 (0.902) max .0325 (0.825) min .002 (0.05) .005 (0.13) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 3. Wrappost geometry. Marking: The Part or Identifying Number (PIN) shall be marked on th

33、e housing and package in accordance with MIL-STD-1285. If size, surface condition, or other design considerations dont allow for full marking on the part, marking on the package is only required. The PIN shall include the complete DSCC PIN, manufacturers name or CAGE code, and date code. The marking

34、 shall be permanent and legible in accordance with method 215 of MIL-STD-202. .BURR .0015 MAX.003 R MAXBCC.0012 MAXIMUM PERMISSIBLEDIVIATION FROM SQUARE ORRECTANGLEAProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUM

35、BUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV H PAGE 8 The PIN shall be constructed using the following format: 89042 -XX -X YY Z Drawing Pin length Plating 1/ Number of positions Temperature range number (dash numbers) (see table II) (see table III) (see table IV) (see table I) 1/ Pla

36、ting designator “C”, selective plating, is not suitable for wire wrap applications. Approved source of supply: An approved source of supply is listed herein. Additional sources will be added as they become available. The vendor listed on the requirements drawing has agreed to this drawing and a cert

37、ificate of compliance has been submitted to DSCC-VAI. DSCC Drawing PIN Vendor CAGE number OAKZ5 1/ 2/ 3/ 8N187 1/ 95238 1/ 89042-01-X-YYZ 89042-02-X-YYZ 89042-03-X-YYZ 89042-04-X-YYZ 89042-05-X-YYZ 89042-06-X-YYZ 89042-07-X-YYZ 89042-08-X-YYZ 89042-09-X-YYZ 89042-10-X-YYZ 89042-11-X-YYZ 89042-12-X-Y

38、YZ 89042-13-X-YYZ 89042-14-X-YYZ 89042-15-X-YYZ 89042-16-X-YYZ 89042-17-X-YYZ 89042-18-X-YYZ 89042-19-X-YYZ 89042-20-X-YYZ 89042-21-X-YYZ 89042-22-X-YYZ 89042-23-X-YYZ 89042-24-X-YYZ 89042-25-X-YYZ SPEG042Z-01-XYYMIL SPEG042Z-02-XYYMIL SPEG042Z-03-XYYMIL SPEG042Z-04-XYYMIL SPEG042Z-05-XYYMIL SPEG042

39、Z-06-XYYMIL SPEG042Z-07-XYYMIL SPEG042Z-08-XYYMIL SPEG042Z-09-XYYMIL SPEG042Z-10-XYYMIL SPEG042Z-11-XYYMIL SPEG042Z-12-XYYMIL SPEG042Z-13-XYYMIL SPEG042Z-14-XYYMIL SPEG042Z-15-XYYMIL SPEG042Z-16-XYYMIL SPEG042Z-17-XYYMIL SPEG042Z-18-XYYMIL SPEG042Z-19-XYYMIL SPEG042Z-20-XYYMIL SPEG042Z-21-XYYMIL SPE

40、G042Z-22-XYYMIL SPEG042Z-23-XYYMIL SPEG042Z-24-XYYMIL SPEG042Z-25-XYYMIL 69157XYY-MIL 68783XYY-MIL 67996XYY-MIL 68737XYY-MIL 68602XYY-MIL 68438XYY-MIL 69133XYY-MIL 68799XYY-MIL 68491XYY-MIL 68481XYY-MIL 68734XYY-MIL 67998XYY-MIL 68691XYY-MIL 68743XYY-MIL 68779XYY-MIL 68749XYY-MIL 68693XYY-MIL 68738X

41、YY-MIL 68464XYY-MIL 68439XYY-MIL 68482XYY-MIL 69132XYY-MIL 68600XYY-MIL N/A N/A H210-YY-01-XZ H210-YY-02-XZ H210-YY-03-XZ H210-YY-04-XZ H210-YY-05-XZ H210-YY-06-XZ H210-YY-07-XZ H210-YY-08-XZ H210-YY-09-XZ H210-YY-10-XZ H210-YY-11-XZ H210-YY-12-XZ H210-YY-13-XZ H210-YY-14-XZ H210-YY-15-XZ H210-YY-16

42、-XZ H210-YY-17-XZ H210-YY-18-XZ H210-YY-19-XZ H210-YY-20-XZ H210-YY-21-XZ H210-YY-22-XZ H210-YY-23-XZ H210-YY-24-XZ H210-YY-25-XZ 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. 2/ Vendor PIN covers “Blank” and “M” temperature ranges only. 3

43、/ Vendor PIN applicable to “Blank” temperature range only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 89042 REV G PAGE 9 Vendor CAGE Vendor name number and ad

44、dress OAKZ5 Mueller-Crane 1208 Massillon Road Building G Suite 1500n Akron OH 44306 8N187 T.T.I 2601 SYLVANIA CROSS DR FORT WORTH, TX 76137 95238 Continental Connector Company 2294 North Penn Road Hatfield, PA 19440 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-