DLA DSCC-DWG-89036 REV B-2001 CONNECTOR ELECTRICAL PLUG RADIO FREQUENCY SERIES BNC PIN CONTACT STRAIGHT AND RIGHT ANGLE FOR M17 152-00001 CABLE《系列BNC插针接触件射频插头直角形连接器 用于 M17 152-0000.pdf

《DLA DSCC-DWG-89036 REV B-2001 CONNECTOR ELECTRICAL PLUG RADIO FREQUENCY SERIES BNC PIN CONTACT STRAIGHT AND RIGHT ANGLE FOR M17 152-00001 CABLE《系列BNC插针接触件射频插头直角形连接器 用于 M17 152-0000.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-89036 REV B-2001 CONNECTOR ELECTRICAL PLUG RADIO FREQUENCY SERIES BNC PIN CONTACT STRAIGHT AND RIGHT ANGLE FOR M17 152-00001 CABLE《系列BNC插针接触件射频插头直角形连接器 用于 M17 152-0000.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONSLTR DESCRIPTION DATE APPROVEDA Add source 00795. Editorial changes throughout. 19 Feb 1991 C. W. KoellerB PIN and source update. 3 August 2001 Robert HeberPrepared in accordance with MIL-STD-100.REVPAGEREVAAAAAREV STATUSOF PAGES PAGE 12345PREPARED BYPMIC N/ARon GaryDEFENSE SUPPLY CENTER, CO

2、LUMBUSCOLUMBUS, OHIO 43216-5000CHECKED BY TITLEC. W. KoellerAPPROVED BYCharles W. KoellerCONNECTOR, ELECTRICAL, PLUG, RADIOFREQUENCY, SERIES BNC, PIN CONTACT, STRAIGHTAND RIGHT ANGLE, FOR M17/152-00001 CABLE.SIZE CAGE CODE037Z3DWG. NO. 89036Original date ofdrawing12 October 1989AREV B PAGE 1 OF 5AMS

3、C N/A 5935-E641-13DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89036DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVBPAGE2FIGURE

4、1. General configuration.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89036DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVBPAGE3NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general inf

5、ormation only.3. Metric equivalents are in parentheses.4. A polyolefin sleeve in accordance with MIL-I-23053/5 shall be supplied with each part.5. Dimension .593 (15.06 mm) is the largest overall diameter of the connector.6. Wrench flats to accommodate standard wrench opening in accordance with FED-

6、STD-H28, appendix 10.7. All undimensioned pictorial configurations are for reference purposes only.8. Dimension 1.500 (38.10 mm) maximum defines the overall length of the connector when assembled to the cable.9. No special tools shall be required for assembly to cables.10. Interface dimensions shall

7、 be in accordance with MIL-STD-348, sereis BNC, pin contact.11. Connectors shall be assembled using the M22520/5-01 crimp tool with die M22520/5-37, closure B. The centercontact shall be solder terminated.12. Gasket material shall be Viton A or an equivalent (Viton A is a trade name of E.I. dupont).

8、FIGURE 1. General configuration - ContinuedNOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.3. Metric equivalents are in parentheses.FIGURE 2. Cable strip dimensions.Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

9、m IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89036DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVBPAGE4ENGINEERING DATA:Nominal impedance: 50 ohms.Frequency range: 0 to 4 GHz.Voltage rating: 500 volts rms sea level.125 volts rms at 70,000 feet.Operating temperature: -65C to +165C.REQUIREMENTS: (R

10、equirements of DSCC drawing 84148 are applicable).Dimensions and configuration: See figure 1 and MIL-STD-348.Force to engage and disengage:Longitudinal force: 3 pounds maximum (13.34 N).Torque: 2.5 inch-pounds, maximum (0.28 Nm).Coupling proof torque: Not applicable.Hermetic seal: Not applicable.Lea

11、kage (pressurized connectors): Not applicable.Center contact retention: 6 pounds minimum axial force (26.69 N).Radial torque: Not applicable.Voltage standing wave ratio (VSWR): The VSWR, when measured in accordance with MIL-PRF-39012, over the frequencyrange of 500 MHz to 4 GHz, or approximately 80

12、percent of the cable cutoff frequency, whichever is lower, shall not exceed1.30:1, (1.35:1 for the right angle).Moisture resistance: MIL-STD-202, method 106, no measurements at high humidity. Insulation resistance shall be at least 200megohms within 5 minutes after removal from humidity.Contact resi

13、stance (in milliohms maximum):AfterInitial environmentalCenter contact (89036BBS) 1.5 1.5Center contact (89036BBS-1) 2.0 2.0Outer contact: 0.2 N/ACable braid to body 0.1 N/ADielectric withstanding voltage: 1,500 V rms, minimum when tested in accordance with MIL-STD-202, method 301.Vibration, high fr

14、equency: MIL-STD-202, test condition B of method 204.Random vibration: MIL-STD-1344, method 2005, test condition V test level F.Corona level: 375 V rms at 70,000 feet (21.336 km).Shock (specified pulse): MIL-STD-202, method 213, test condition G.Thermal shock: MIL-STD-202, method 107, test condition

15、 C.Altitude: The connector shall operate as specified herein, at altitudes up to and including 70,000 feet (21.336 km).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89036DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5

16、000AREVBPAGE5RF high potential withstanding voltage: 1,000 V rms, minimum.Frequency: 5 to 7.5 MHz.Leakage current: Not applicable.Cable retention force: 10 pounds, minimum axial pull (44.48 N).Coupling mechanism retention force: 100 pounds, minimum (444.8 N).RF leakage: 55 dB, minimum tested between

17、 2 to 3 GHz.RF insertion loss: 0.2 dB, maximum tested at 3 GHz (89036BBS).0.3 dB, maximum tested at 3 GHz (89036BBS-1).Cable accommodation: M17/152-00001.Part or Identifying Number (PIN): 89036BBS (straight) and 89036BBS-1 (right angle).NOTE: These connectors are for use in radio frequency applicati

18、ons only.Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as theybecome available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate ofcompliance has been submitted to DSCC-VAI.DSCC drawingPIN 1/Vend

19、or CAGEnumberVendor referencePIN89036BBS 00795 1003100A001-00089036BBS-1 00795 1007100A001-0001/ Parts must be purchased to this DSCC PIN to assure that allperformance requirements and tests are met.Vendor CAGE Vendor namenumber and address00795 Delta Electronics416 Cabot StreetBeverly, MA 01915Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-