DLA DSCC-DWG-88036 REV B-2011 RESISTOR NETWORK 10 PIN LEADLESS CHIP CARRIER.pdf

《DLA DSCC-DWG-88036 REV B-2011 RESISTOR NETWORK 10 PIN LEADLESS CHIP CARRIER.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-88036 REV B-2011 RESISTOR NETWORK 10 PIN LEADLESS CHIP CARRIER.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update and validation of drawing. Change reference specification to MIL-PRF-914. Editorial changes throughout. 24 Aug 2000 K. Cottongim B 5 Year review cycle. Editorial changes throughout 21 Sept 2011 M. Radecki Prepared in accordance with ASME Y14.100 Sour

2、ce control drawing REV STATUS OF PAGES REV B B B B B B B PAGES 1 2 3 4 5 6 7 PMIC N/A Original date of drawing: 3 June 1988 PREPARED BY Dennis L. Cross DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY David E. Moore TITLE RESISTOR NETWORK, 10 PIN, LEADLESS CHIP CARRIER APPROVED BY David E. Mo

3、ore SIZE A CODE IDENT. NO. 14933 DWG NO. 88036 REV B PAGE 1 OF 7 AMSC N/A 5905-E620CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DLA LAND AND MARITIME COLUMBUS OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTE

4、R COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88036 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 10 pin, leadless chip carrier, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 88036 - 001 | | Drawing number Dash number

5、22. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the cited in the sol

6、icitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-914 - Resistors Networks, Fixed, Film, Surface Mount, Nonestablished Reliability, and Established Reliability, General Specification For. DEPARTMENT OF DEFENSE STANDARD MIL-STD-1285 - Marking of Electrical and Electronic Pa

7、rts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a

8、 conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been

9、 obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-914 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-914 and herein (see figure

10、1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88036 REV B PAGE 3 Inches mm Inches mm Inches mm Inches mm Inches mm .001 0.003 .010 0.025 .028 0.071 .050 0.127

11、.250 0.635 .002 0.005 .020 0.051 .030 0.076 .080 0.203 .003 0.008 .025 0.064 .035 0.089 .170 0.432 .004 0.010 .027 0.069 .040 0.102 .210 0.533 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .005 (0.13 mm) f

12、or three decimal places and .010 (0.25 mm) for two decimal places. 3. The picturization of the style above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device,

13、are acceptable. 4. Terminal 1 indicator shall be a notch, dot, or the numeral 1. This should be located at a point that clearly indicates terminal 1. FIGURE 1. Resistor network. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPP

14、LY CENTER COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88036 REV B PAGE 4 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance shall be as specified in table I. TABLE I. Resistance values. Dash number Resistance R1 R2 R3 R4 R5 R6 R7 R8 001 2.921k 2.068k 1.464k 3.548k 7.488k 1.881k

15、0.1843k 0.4467k 002 0.71k 2.0k 2.0k 0.71k NC NC NC NC 003 2.0k 2.0k 2.0k 2.0k NC NC NC NC 004 1.881k 0.631k 7.488k NC NC NC NC NC 005 4.988k 5.012k NC NC NC NC NC NC 3.3.2 Resistance tolerance. Resistors are available in (F) 1 percent tolerance. 3.3.3 Power rating. The power rating shall be 0.10 wat

16、ts at 70OC derated to zero power at 125OC in accordance with figure 2. FIGURE 2. Derating curve. 3.3.4 Package power rating. The package power rating shall be 0.10 watts times the number of individual elements. 3.3.5 Schematic. The schematic of the resistor network shall be identified as shown on fi

17、gure 3 below. The resistor element RREFshall be the reference resistor element used in determining the ration accuracy (when applicable). 3.3.6 Operating voltage. The maximum operating voltage shall be 30 Vdc. 3.3.7 Operating temperature. The operating temperature shall be -55OC to +125OC. 3.3.8 Res

18、istance temperature characteristic. The resistance temperature characteristic shall conform to characteristic “V” of MIL-PRF-914. 3.3.9 TC tracking. The TC tracking shall be 5 ppm/OC. 3.3.10 Ratio accuracy. The ratio accuracy shall be 0.05 percent. -60 -40 -20 0 20 60 80 100 120 140 160 180 Temperat

19、ure (OC) 125OC 100 80 60 40 20 0 70OC -55OC Percentofrated powerProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88036 REV B PAGE 5 3.3.11 Pure tin. The use of pure t

20、in, as an underplate or final finish, is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). FIGURE 3. Schematics. 3.4 Marking. Marking shall be in acc

21、ordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.5 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-914 Qualified Products List f

22、or at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime - VA. 3.5.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as a su

23、ggested source of supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88036 REV B PAGE 6 3.6 Recycled, recovered, or environmentally preferable materials. Recycl

24、ed, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. Resistors shall be uniform in quali

25、ty and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-914 is not applicable to this document. 4.2 Qualification inspection. Qualification inspection is not applicable to thi

26、s document. 4.2.1 Failure rate qualification. The failure rate qualification specified in MIL-PRF-914 is not applicable to this document. 4.3 Conformance inspections. 4.3.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-

27、PRF-914. 4.3.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.4 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-914. 4.5 Visual and mecha

28、nical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-914. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall b

29、e as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inv

30、entory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments Services System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by con

31、tacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended to be used in thick or thin film circuits where microcircuity is intended, also, for us

32、e in surface mounting application. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88036 REV B PAGE 7 6.2 Ordering data. The contract or purchase order should specif

33、y the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Packaging requirements (see 5.1). (i.e. Electrostatic

34、 discharge sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certificate of compliance with group B (see 4.3.2). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufactu

35、re. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, b

36、y mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by e

37、lectrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to Government is controlled by MIL-DTL-39032 that specifies a preventative packaging procedure. 6.5 Pulse applications. Designers are CAUTIONED on using the

38、se resistors in pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. These resistors only see a onetime pulse (Short-time overload) as part of the group B inspection. 6.6 Users of record. Coordination of this document for

39、 future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved on-line at resistordla.mil or in writing to: DLA Land and Maritime, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218

40、-3990 or by telephone (614) 692-8754 or DSN 850-8754. 6.7 Sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained on on-line at resistordla.mil or contact DLA Land and Maritime,

41、ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990, or by telephone (614) 692-8754 or DSN 850-8754. DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendors name and address 88036- 001 002 003 004 005 L019 L013 L014 L010 L011 57027 IRC, Inc. 4222 S. Staples Street Corpus Christi, TX 78411-2702 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and test are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-