DLA DSCC-DWG-86106 REV D-2001 CONNECTOR RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES N FOR SEMIRIGID CABLE《N型半刚性射频同轴电缆电容连接器》.pdf

《DLA DSCC-DWG-86106 REV D-2001 CONNECTOR RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES N FOR SEMIRIGID CABLE《N型半刚性射频同轴电缆电容连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86106 REV D-2001 CONNECTOR RECEPTACLE ELECTRICAL COAXIAL RADIO FREQUENCY SERIES N FOR SEMIRIGID CABLE《N型半刚性射频同轴电缆电容连接器》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add source 26805. 29 Nov 1988 Randy Larson B Change vendor part numbers. Editorial changes throughout. 8 Oct 1991 Randy Larson C Add new vendor PINs and address change for CAGE 95077. 10 Nov 1994 Randy Larson D PIN and source update. 16 Nov 2001 Robert M. He

2、ber Prepared in accordance with MIL-STD-100 REV PAGE REV D D D D D D D REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 PREPARED BY PMIC N/A Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE C. W. Koeller APPROVED BY R. Larson CONNECTOR, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO

3、 FREQUENCY, SERIES N FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 86106 Original date of drawing 16 May 1986 A REV D PAGE 1 OF 7 AMSC N/A 5935-E628 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitt

4、ed without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86106 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Dimensions 1.750 (44.45 mm) and .940 (23.88 mm) are the largest overa

5、ll dimensions of the connector. 4. Wrench flats, when applicable, are to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10. 5. All undimensioned pictorial representations are for reference purposes only. 6. Dimension 1.750 (44.45 mm) defines the masximum length of the c

6、onnector when assembled to the appropriate cable. 7. Interface shall be in accordance with MIL-STD-348, series N, socket contact. 8. Gold plating (when required) shall be applied at least in the area of solder attachment. FIGURE 1. Dimensions and configuration. Inches mm .022 0.56 .120 3.05 .130 3.3

7、0 .250 6.35 .526 13.36 .531 13.49 .532 13.51 .543 13.79 .625 15.88 .630 16.00 .645 16.38 .745 18.92 .753 19.13 .880 22.35 .940 23.88 1.750 44.45 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86106 DEFENSE SUPPLY CENTER,

8、 COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 3 Inches mm .100 2.54 .125 3.18 FIGURE 2. Cable strip dimensions. ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 18 GHz. Voltage rating: 500 volts rms maximum working voltage at sea level. 125 volts rms maximum at 70,000 feet. Tempe

9、rature rating: -65C to +105C for M17/129-RG401. -65C to +105C for M17/130-RG402, M17/130-00001, 00002, 00003. REQUIREMENTS: Requirements of drawing 84148 are applicable. Dimensions and configuration: See figure 1. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 6 inch-poun

10、ds maximum. Inspection conditions: For each test of threaded coupling connector where the test is performed on mated pairs, the pairs shall be torque to 6 to 10 inch-pounds. .125 (3.18).100 (2.54)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE C

11、AGE CODE DWG NO. 037Z3 86106 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 4 Mating characteristics: See MIL-STD-348 for dimensions. Center contact (socket): Oversize test pin: 0.074 diameter minimum (nonclosed entry contact only). Insertion depth: .125 minimum. Number of inse

12、rtions: 1. Insertion force test: Steel test pin diameter .066 minimum. Test pin finish: 16 microinches. Insertion force: 2 pounds maximum. Insertion depth: .125/.140. Withdrawal force test: Steel test pin diameter .063 maximum. Withdrawal force: 2 ounces minimum. Test pin finish: 16 microinches. Ins

13、ulation resistance: Method 3003 of MIL-STD-1344; 5,000 megohms minimum. Center contact retention (applicable to captivated center contact connectors only): 6 pounds minimum axial force. Corrosion (salt spray): Method 1001 of MIL-STD-1344, test condition B. Voltage standing wave ratio (VSWR): From 2.

14、0 to 18.0 GHz, 1.15 +.012 times frequency (GHz). Swept frequency VSWR test setup: Item 6: VSWR shall be less than 1.008 +.002 F (F in GHz). Item 16: VSWR shall be less than 1.008 +.002 F (F in GHz). Second step of VSWR checkout procedure: VSWR shall be less than 1.012 +.004 F (F in GHz). Group B ins

15、pection: VSWR shall be less than 1.024 +.007 F (F in GHz). Qualification and group C inspection: VSWR shall not exceed 1.08. Connector durability: Method 2016 of MIL-STD-1344. 500 cycles at 12 cycles per minute maximum: The connector shall meet the mating characteristics and force to engage and dise

16、ngage requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86106 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 5 Contact resistance (in milliohms maximum): Initial After environmental Cente

17、r contact 1.5 2.0 Outer contact .2 Not applicable Outer contact (stainless steel) 2.0 Not applicable Cable outer conductor to body .05 Not applicable Cable outer conductor to 2.0 Not applicable stainless steel body Dielectric withstanding voltage: Method 3001 of MIL-STD-1344. 1,500 volts rms minimum

18、 at sea level. Vibration, high frequency: Method 2005 of MIL-STD-1344, test condition IV, except the method of mounting shall be approved by the qualifying activity, and 30 gs peak will be applicable. Shock: Method 2004 of MIL-STD-1344, test condition G. Thermal shock: Method 1003 of MIL-STD-1344, t

19、est condition A, except test high temperature shall be +115C. Humidity: Method 1002 of MIL-STD-1344. No measurements at high humidity. Insulation resistance shall be at 200 megohms within 5 minutes after removal from humidity. Corona level: Altitude: 70,000 feet. Cable (semirigid) V rms M17/129-RG40

20、1 500 M17/130-RG402, M17/130-00001, 00002, 00003 375 RF high potential withstanding voltage: Frequency: 5 to 7.5 MHz inclusive. Leakage current: Not applicable. Cable (semirigid) V rms M17/129-RG401 1,200 M17/130-RG402, M17/130-00001, 00002, 00003 1,000 Provided by IHSNot for ResaleNo reproduction o

21、r networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86106 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 6 Cable retention: Cable Force Torque M17/129-RG401 90 pounds minimum 70 inch-ounces minimum M17/130-RG402, M17/130-00001, 60 pounds minimum 55

22、inch-ounces minimum 00002, 00003 RF leakage: -90 dB minimum, tested at a frequency between 2 and 3 GHz. Insertion loss: dB maximum = .10 f(GHz). Test frequency 6.0 GHz. Part or Identifying Number (PIN): See table I. TABLE I. PIN to cable accommodation. Connector PIN 1/ 2/ 3/ Cable 86106NBSA 86106NSG

23、A M17/130-RG402 M17/130-00001 M17/130-00002 M17/130-00003 86106NBSB 86106NSGB M17/129-RG401 1/ These connectors have captivated center contacts. 2/ Connectors for RG401 (.250 inch) cable shall not be assembled by solder or by special tools. 3/ These parts are for use in general radio frequency appli

24、cations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 86106 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV D PAGE 7 Approved sources of supply are listed herein. Additional sources will be added as they

25、become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to the DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 1/ Replacement military specification PIN 86106NBSA 95077 6545-0021 M39012/132-0003 86106NBSB 95077

26、6545-0022 M39012/132-0002 86106NSGA 95077 6545-6021 M39012/132-3003 86106NSGB 95077 6545-6022 M39012/132-3002 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 95077 Solitron/Vector Microwave Products 3301 Electronics Way West Palm Beach, FL 33407 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-