DLA DSCC-DWG-85105 REV D-2013 GASKET SHIELDING EMI RFI O-RING CIRCULAR CROSS SECTION.pdf

《DLA DSCC-DWG-85105 REV D-2013 GASKET SHIELDING EMI RFI O-RING CIRCULAR CROSS SECTION.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85105 REV D-2013 GASKET SHIELDING EMI RFI O-RING CIRCULAR CROSS SECTION.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Drawing revised to reference MIL-G-83528. 22 Aug 1987 Randy Larson B Inactivate for new design materials contained herein which are qualified to MIL-G-83528. Add supersession table to section six. 4 Aug 1988 Randy Larson C Incorporated boilerplate updates.

2、19 Feb 2008 Michael A. Radecki D Incorporated boilerplate updates. 16 December 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV D D D D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Frank A Crivello DESIGN ACTIVITY DEFENSE ELECTRON

3、ICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 26 Feb 1986 CHECKED BY Randy Larson TITLE GASKET, SHIELDING, EMI/RFI, O-RING, CIRCULAR CROSS SECTION APPROVED BY Ivan R. Jones SIZE A CODE IDENT. NO. 14933 DWG NO. 85105 REV D PAGE 1 OF 13 AMSC N/A 5999-2014-E03CURRENT DESIGN ACTIVITY

4、CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY LAND AND MARITIME COLUMBUS, OHIO 43218-3990 INACTIVE FOR NEW DESIGN Material types contained herein which have qualified MIL-DTL-83528 sources are inactive for new design. Gaskets made of materials not yet qualified to MIL-DTL-83528 may continue to be procure

5、d to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of EMI/

6、RFI gaskets, elastomer, solid circular strip. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85105 _A_ -01 _ Drawing number Material Dash number (see 3.2) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this

7、specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requ

8、irements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherw

9、ise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-83528 - Gasketing Material, Conductive, Shielding Gasket, Electronic Elastomer, EMI/RFI, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285

10、- Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event o

11、f a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensio

12、ns. See figure 1 and table I. 3.2 Characteristics. Characteristics shall be in accordance with MIL-DTL-83528. 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that th

13、e material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.4 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-DTL-83528 Qualified Product List for

14、at least one part, or perform the group A inspection specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SI

15、ZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalent are for information only. 3. Metric equivalents are in parentheses. 4. Molding flash of .035 inch width maximum is allowed. FIGURE I. Interface and physical dimensions. Provided by IHSNot f

16、or ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 4 Dash number Dimensions Dash number Dimensions Dash number Dimensions Dash number Dimensions B +.005 (0.13) C +.005 (0.1

17、3) B +.005 (0.13) C +.005 (0.13) B +.005 (0.13) C +.005 (0.13) B +.005 (0.13) C +.005 (0.13) 001 .030 (0.76) .442 (11.23) 022 .070 (1.78) .610 (15.49) 043 .070 (1.78) 1.485 (37.72) 064 .101 ( 2.57) 3.153 ( 80.07) 002 .030 (0.76) .557 (14.66) 023 .070 (1.78) .635 (16.13) 044 .070 (1.78) 1.609 (40.87)

18、 065 .101 ( 2.57) 3.613 ( 91.77) 003 .030 (0.76) .692 (17.58) 024 .070 (1.78) .677 (16.94) 045 .070 (1.78) 1.614 (41.00) 066 .103 ( 2.62) .612 ( 15.54) 004 .030 (0.76) .817 (20.75) 025 .070 (1.78) .676 (17.17) 046 .070 (1.78) 1.674 (42.52) 067 .103 ( 2.62) .799 ( 20.29) 005 .039 (0.99) .425 (10.80)

19、026 .070 (1.78) .738 (18.75) 047 .070 (1.78) 1.735 (44.07) 068 .103 ( 2.62) 1.040 ( 26.42) 006 .048 (1.22) .295 ( 7.49) 027 .070 (1.78) .735 (18.67) 048 .070 (1.78) 1.864 (47.35) 069 .103 ( 2.62) 1.240 ( 31.50) 007 .050 (1.27) .533 (13.54) 028 .070 (1.78) .739 (18.77) 049 .070 (1.78) 1.980 (50.29) 0

20、70 .103 ( 2.62) 1.362 ( 34.59) 008 .051 (1.30) .446 (11.33) 029 .070 (1.78) .801 (20.35) 050 .070 (1.78) 3.009 (76.43) 071 .103 ( 2.62) 1.487 ( 37.77) 009 .057 (1.45) .415 (10.54) 030 .070 (1.78) .860 (21.85) 051 .070 (1.78) 3.170 (80.52) 072 .103 ( 2.62) 1.612 ( 40.94) 010 .063 (1.60) .541 (13.74)

21、031 .070 (1.78) .864 (21.95) 052 .070 (1.78) 3.489 (88.62) 073 .103 ( 2.62) 1.737 ( 44.12) 011 .063 (1.60) .648 (16.46) 032 .070 (1.78) .926 (23.52) 053 .076 (1.93) .656 (16.66) 074 .103 ( 2.62) 1.790 ( 45.47) 012 .068 (1.73) .847 (21.51) 033 .070 (1.78) .989 (25.12) 054 .076 (1.93) .779 (19.79) 075

22、 .103 ( 2.62) 2.362 ( 59.99) 013 .068 (1.73) 1.182 (30.02) 034 .070 (1.78) 1.046 (26.57) 055 .084 (2.13) .852 (21.64) 076 .103 ( 2.62) 3.987 (101.27) 014 .068 (1.73) 3.1;65 (80.39) 035 .070 (1.78) 1.110 (28.19) 056 .084 (2.13) 2.678 (68.02) 077 .115 ( 2.92) 2.876 ( 73.05) 015 .070 (1.78) .145 ( 3.68

23、) 036 .070 (1.78) 1.114 (28.30) 057 .084 (2.13) 1.250 (31.75) 078 .147 ( 3.73) 2.265 ( 57.53) 016 .070 (1.78) .301 ( 7.65) 037 .070 (1.78) 1.176 (29.87) 058 .087 (2.21) 2.360 (59.94) 079 .147 ( 3.73) 3.690 ( 93.73) 017 .070 (1.78) .364 ( 9.25) 038 .070 (1.78) 1.230 (31.24) 059 .094 (2.39) .750 (19.0

24、5) 080 .188 ( 4.78) .673 ( 17.09) 018 .070 (1.78) .426 (10.82) 039 .070 (1.78) 1.239 (31.47) 060 .095 (2.41) .897 (22.78) 081 .210 ( 5.33) 3.475 ( 12.07) 019 .070 (1.78) .489 (12.42) 040 .070 (1.78) 1.296 (32.92) 061 .095 (2.41) 1.074 (27.28) 082 .243 ( 6.17) 3.409 ( 86.59) 020 .070 (1.78) .495 (12.

25、57) 041 .070 (1.78) 1.362 (34.59) 062 .100 (2.54) 1.005 (25.53) 083 .394 (10.01) 3.464 ( 87.99) 021 .070 (1.78) .551 (14.00) 042 .070 (1.78) 1.364 (34.65) 063 .101 (2.57) 2.805 (71.25) 084 .138 ( 3.51) 2.011 ( 51.08) 085 .115 ( 2.92) 2.683 ( 68.15) FIGURE 1. Interface and physical dimensions - Conti

26、nued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 5 TABLE I. Cross section area. Dash number PIN Cross section area (cm2) * Dash number PIN Cross

27、 section area (cm2) * Dash number PIN Cross section area (cm2) * Dash number PIN Cross section area (cm2) * 001 0.0046 023 0.0248 045 0.0248 067 0.0538 002 “ 024 “ 046 “ 068 “ 003 “ 025 “ 047 “ 069 “ 004 “ 026 “ 048 “ 070 “ 005 0.0077 027 “ 049 “ 071 “ 006 0.0117 028 “ 050 “ 072 “ 007 0.0127 029 “ 0

28、51 “ 073 “ 008 0.0132 030 “ 052 “ 074 “ 009 0.0165 031 “ 053 0.0293 075 “ 010 0.0201 032 “ 054 0.0293 076 “ 011 0.0201 033 “ 055 0.0358 077 0.0670 012 0.0234 034 “ 056 0.0358 078 0.1095 013 “ 035 “ 057 0.0384 079 0.1095 014 “ 036 “ 058 0.0384 080 0.1791 015 0.0248 037 “ 059 0.0448 081 0.2235 016 “ 0

29、38 “ 060 0.0457 082 0.2992 017 “ 039 “ 061 0.0457 083 0.7866 018 “ 040 “ 062 0.0507 084 0.0965 019 “ 041 “ 063 0.0517 085 0.0670 020 “ 042 “ 064 0.0517 021 “ 043 “ 065 0.0538 022 “ 044 “ 066 0.0538 * For volume resistivity (surface probe) calculation. Provided by IHSNot for ResaleNo reproduction or

30、networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 6 3.5 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.6

31、Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of gasket components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.5). 3.7 Material. The material shall b

32、e as specified in the PIN according to designations A, B, C, D, E, F, H, J, or K. These designations shall be in accordance with MIL-DTL-83528. 3.8 Marking. Marking shall be in accordance with MIL-STD-1285, except the delay line shall be marked with the PIN as specified herein (see 1.2), the manufac

33、turers name or Commercial and Government Entity (CAGE) code and date lot codes. 3.9 Workmanship. The gasket shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, sampling an

34、d inspection procedures shall be performed in accordance with MIL-DTL-83528. 4.2 In-process inspection. In-process inspection shall be in accordance with MIL-DTL-83528. 4.3 Conformance inspection. Conformance inspection shall consist of the group A inspection. 4.4 Inspection of product for delivery.

35、 Inspection of product for delivery shall consist of the group A inspection. 4.5 Group A inspection. Group A inspection shall be in accordance with MIL-DTL-83528. 4.6 Methods of inspection. Methods of inspection shall be in accordance with MIL-DTL-83528. 5. PACKAGING 5.1 Packaging. For acquisition p

36、urposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requi

37、rements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-RO

38、M products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Gaskets conforming to this drawing are intended for use when military specifications do not e

39、xist and qualified military devices that will perform the required function are not available for the OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and one copy of the conformance inspection d

40、ata or the certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY

41、CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 7 6.3 Replaceability. Devices covered by this drawing will replace the commercial device covered by a contractor prepared specification or drawing. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 per

42、cent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will

43、not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Users of record. Coordination of this docum

44、ent for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto:relaydla.mil or if in writing to: DLA Land and Maritime, ATTN: DLA Land and Maritime/V

45、AT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.6 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online

46、at mailto:relaydla.mil, or by contacting DLA Land and Maritime, ATTN: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELE

47、CTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85105 REV D SHEET 8 DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/ 2/ 3/ Vendor CAGE Vendor name and address 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022

48、 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 10-00-2231-XXXX 10-00-2232-XXXX 10-00-2259-XXXX 10-00-2233-XXXX 10-00-1413-XXXX 10-00-2777-XXXX 10-00-1406-XXXX 10-00-1405-XXXX 10-00-1407-XXXX 10-00-1376-XXXX 10-00-1342-XXXX 10-00-1631-XXXX 10-

49、00-1770-XXXX 10-00-1478-XXXX 10-00-3811-XXXX 10-00-2226-XXXX 10-00-5983-XXXX 10-00-2227-XXXX 10-00-1980-XXXX 10-00-0008-XXXX 10-00-2065-XXXX 10-00-0010-XXXX 10-00-2085-XXXX 10-00-1689-XXXX 10-00-2066-XXXX 10-00-1690-XXXX 10-00-0012-XXXX 10-00-2075-XXXX 10-00-1981-XXXX 10-00-0014-XXXX 10-00-2076-XXXX 10-00-1843-XXXX 10-00-2068-