DLA DSCC-DWG-85036 REV B-2003 SUPPORT ELECTRICAL CARD HOLDER SPACER《有间隔基的电卡座支架》.pdf

《DLA DSCC-DWG-85036 REV B-2003 SUPPORT ELECTRICAL CARD HOLDER SPACER《有间隔基的电卡座支架》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85036 REV B-2003 SUPPORT ELECTRICAL CARD HOLDER SPACER《有间隔基的电卡座支架》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changed dimensions on figure 1. Added dash number 18. Editorial changes throughout. 5 AUG 1988 Randy Larson B Replaced canceled documents and changed FSC. Editorial changes throughout. 31 JAN 2003 Thomas Hess Prepared in accordance with ASME Y14-100 Selecte

2、d item drawing REV PAGE REV STATUS REV B B B B B B OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Dan McGrath DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 8 November 1985 CHECKED BY Randy Larson TITLE SUPPORT, ELECTRICAL CARD HOLDER, SPACER APPROV

3、ED BY Ivan R. Jones SIZE A CODE IDENT. NO. 14933 DWG NO. 85036 REV B PAGE 1 OF 6 AMSC N/A 5998-E042 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-50

4、00 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85036 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of spacers for use with

5、card holder support bars specified in DSCC drawing 85075. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85036 Drawing number 01 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following spec

6、ifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the s

7、olicitation (see 6.2). STANDARDS DEPARTMENT OF DEFENSE MILSTD1285 Marking of Electrical and Electronic Parts. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Document Automation and Production Service, Building 4D (DAPS-DODS

8、SP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited

9、 in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM D4066 Nylon Injection and Extrusion Materials (PA) (Application for copies should be addressed to the

10、 ASTM International, 100 Barr Harbor Drive, West Coshohocken, PA 19428-2959.) (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informa

11、tional services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obta

12、ined. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensions shall be as specified in table I and figure 1. 3.2 Materials. The material shall nylon in accordance with ASTM D4066. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

13、thout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85036 REV B PAGE 3 TABLE I. Length dimensions. 1/ PIN 85036 Dimension “X” +.005/.000 (+0.13/0.0) PIN 85036 Dimension “X” +.005/.000 (+0.13/0.0) Inches mm Inches mm 01 .031 ( 0.79 ) 10 .300 (

14、 7.62 ) 02 .062 ( 1.57 ) 11 .312 ( 7.92 ) 03 .100 ( 2.54 ) 12 .375 ( 9.53 ) 04 .125 ( 3.18 ) 13 .437 ( 11.1 ) 05 .152 ( 3.86 ) 14 .500 ( 12.7 ) 06 .173 ( 4.39 ) 15 .700 ( 17.8 ) 07 .187 ( 4.75 ) 16 .750 ( 19.1 ) 08 .200 ( 5.08 ) 17 1.000 ( 25.4 ) 09 .250 ( 6.35 ) 18 .562 ( 14.28 ) 1/ See figure 1 fo

15、r dimension “X”. Inches mm Inches mm Inches mm Inches mm Inches mm .007 .010 .040 0.17 0.25 1.01 .060 .075 .080 1.52 1.90 2.03 .095 .107 .109 2.41 2.71 2.76 .265 .427 .445 6.73 10.84 11.30 .64 .85 16.3 21.2 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only

16、. 2. Unless otherwise specified, tolerances are for .010 inch (0.25 mm) for two place decimals and .005 (0.13 mm) for three place decimals. 3. All trapezoidal wedge bodies (ends and middle) may or may not have a chamfer as shown. The overall length of the wedge bodies with chamfers will be reduced.

17、4. See table I for dimension X. 5. Groove in 85036-17 only. FIGURE 1. Dimensions and configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85036 REV B PAGE 4

18、 3.3 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.3.1 Optional statement of compliance in lieu of testing. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compli

19、ance in lieu of the manufacturer performing the inspection of product for delivery tests (see 4.2.2 and 6.2.b). 3.4 Marking. Marking of the spacer is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufa

20、cturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds t

21、he operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Workmanship. Spacers shall be free of flash, pits, voids, cracks, and excessive mold marks. A visible parting line is acceptable. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise sp

22、ecified in the contract or order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use their own or any other facilities suitable for the performance of the inspection requirements

23、specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Conformance inspections. 4.2.1 Ins

24、pection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.6). Criteria for defects are listed in 4.2.5. 4.2.2 Optional statement of compliance. The

25、 acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.2.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defec

26、ts are found, the lot shall be rejected. Criteria for defects are listed in 4.2.5. TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 to 35,001

27、29 35 35,001 and over 29 40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85036 REV B PAGE 5 4.2.4 Rejected lots. If an inspection lot is rejected after normal sampl

28、ing inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sa

29、mple, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.2.5 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical

30、 and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. 5. PACKAG

31、ING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging

32、 requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys

33、 automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Spacers conforming to this drawing are intended for use when

34、 performance specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract or order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the con

35、formance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions are coordinated only with the sugges

36、ted sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail at “5998.Documentdscc.dla.mil” or by f

37、acsimile (614) 692-6939 or DSN 850-6939. 6.4 Replaceability. Spacers covered herein replace similar commercial devices covered by contractor-prepared specification or drawing. 6.5 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they bec

38、ome available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail at “5998.Documentdscc.dla.mil” or by facsimile (614) 692-6939 or DSN 850-6939. Provided by IHSNot for ResaleNo reprod

39、uction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85036 REV B PAGE 6 DSCC drawing PIN 85036 Vendor similar designation or type number 1/ DSCC drawing PIN 85036 Vendor similar designation or type number 1/ Ve

40、ndor CAGE Vendor name and address 01 02 03 04 05 06 07 08 09 T101031 T101062 T101100 T101125 T101152 T101173 T101187 T101200 T101250 10 11 12 13 14 15 16 17 18 T101300 T101312 T101375 T101437 T101500 T101700 T101750 T1011000 T101562 18915 APW / Electronic Solutions 14100 Danielson Street Poway, CA 9

41、2064-6898 Tel: (858) 679-4550 Toll Free: (800) 854-7086 Fax: (858) 679-4555 Electronic-mail: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-