DLA DSCC-DWG-05011-2005 CONNECTOR PLUG ELECTRICAL RADIO FREQUENCY 2 4MM FOR SEMIRIGID CABLE (WITHOUT CONTACT)《半刚性电缆(无接触)用 无线电频率2 4毫米 电工插头连接器》.pdf

《DLA DSCC-DWG-05011-2005 CONNECTOR PLUG ELECTRICAL RADIO FREQUENCY 2 4MM FOR SEMIRIGID CABLE (WITHOUT CONTACT)《半刚性电缆(无接触)用 无线电频率2 4毫米 电工插头连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-05011-2005 CONNECTOR PLUG ELECTRICAL RADIO FREQUENCY 2 4MM FOR SEMIRIGID CABLE (WITHOUT CONTACT)《半刚性电缆(无接触)用 无线电频率2 4毫米 电工插头连接器》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 CHECKED BY T

2、ITLE Mary McWilliams APPROVED BY Richard Taylor CONNECTOR, PLUG, ELECTRICAL, RADIO FREQUENCY 2.4mm, FOR SEMIRIGID CABLE (Without Contact) SIZE CAGE CODE 037Z3 DWG. NO. 05011 Original date of drawing 30 November 2005 A REV PAGE 1 OF 9 AMSC N/A 5935-E788 Provided by IHSNot for ResaleNo reproduction or

3、 networking permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Metric equivalents are in parentheses. 4. Dimension .400 (10.16) is the largest overall envelope of the connector. 5. Wrench flats to accommodate standard w

4、rench per FED-STD-H28, appendix 10. 6. Dimension “A” defines the maximum length of connector when assembled to cable. 7. When applicable, three holes .016 (0.41 mm) minimum diameter, equally spaced, are required for safety wiring after mating. Location on the coupling nuts optional. 8. All threads s

5、hall conform to FED-STD-H28. 9. Series 2.4mm, interface in accordance with figure 2. Coupling nut thread size shall be M7 X .75-6H. 10. All undimensioned pictorial representations are for reference purposes only. FIGURE 1. General configuration. SIZE CAGE CODE DWG NO. 037Z3 05011 DEFENSE SUPPLY CENT

6、ER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTES. 1. Insulator to be flush to -.003 below reference plane. 2. With coupling nut biased in the forward direction. 3. See the manufactu

7、rers assembly instructions for cable preparation. FIGURE 2. DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.4 mm Connector Interface. SIZE CAGE CODE DWG NO. 037Z3 05011 A REVPA

8、GE3 Inches mm .010 0.25 .053 1.35 .057 1.45 TABLE I. Dash number and applicable cable. PIN Applicable cable 1/ Dimension A 2/ CATEGORY E FIELD REPLACEABLE (STANDARD ASSEMBLY TOOL KIT) 3/ 4/ 5/ 6/ 05011ZSPA 05011ZCGA 05011ZSPA-1 7/ 05011ZCGA-17/ M17/133-RG405 M17/133-00001 Through M17/133-00018 .460

9、(11.68 mm) maximum * Cable to be used when performing test requiring cable. 1/ MIL-DTL-17 cables are specified by the basic number. The latest version of each cable shall be applicable. 2/ Dimension A determines the closeness of a bend in the cable to the rear of the connector. 3/ For logistics purp

10、oses, only connectors with safety wire holes will be stocked. 4/ Coupling nuts shall be corrosion-resistant steel with a passivated finish in accordance with MIL-F-14072 for connectors with corrosion-resistant steel bodied connectors. 5/ Kit number Amphenol 901-2500, or equivalent. 6/ All corrosion-

11、resistant steel-bodied connectors shall be Gold plated in accordance with ASTM B488, type II code C, class 1.27, over 50 micro inches (1.27 micro meters) minimum of nickel in accordance with SAE-AMS-QQ-N-290 at least in the area of solder attachment. 7/ No safety wire holes. SIZE CAGE CODE DWG NO. 0

12、37Z3 05011 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Cable Dimension “A“(dielectric) M17/133-RG405 M17/133-00001 Through M17/133-00018 .078 +.002 See manufacture

13、rs assembly instructions for cable preparation. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parenthesis and are given for information only. FIGURE 3. Cable stripping dimensions for category E connectors. SIZE CAGE CODE DWG NO. 037Z3 05011 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BO

14、X 3990, COLUMBUS, OH 43218-3990 A REVPAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 to 50 GHz. Voltage rating: The voltage rating shall be in accordance with table II. TABLE II.

15、Voltage rating. Cable Voltage maximum (at sea level) Voltage maximum (70,000 feet) M17/133-RG405 M17/133-00001 through M17/133-00018 V rms335 V rms85 Temperature rating: -65C to +165C. REQUIREMENTS: Dimensions and configuration: See figures 1 and 2. Force to engage and disengage: Longitudinal force:

16、 Not applicable. Torque: 2 inch-ounces maximum. Coupling proof torque: 15 inch-pounds, minimum. Safety wire hole tear out: 15 pounds, minimum. Inspection conditions: For each test of threaded coupling connector where the test is performed on mated pairs, the pairs shall be torqued to 7 to 10 inch-po

17、unds. Mating characteristics: See Figure 2. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Insulation resistance: Method 302, test condition B of MIL-STD-202, 5,000 megohms, minimum. Center contact retention: Not applicable. Radial torque: Not applicable. Corrosion

18、(salt spray): Method 101, test condition B of MIL-STD-202. SIZE CAGE CODE DWG NO. 037Z3 05011 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Voltage standing wave rat

19、io (VSWR): 1.20:1, maximum, from 0.5 to 50 GHz, or approximately 80 percent of upper cutoff frequency of the cable, whichever is lower. Swept frequency VSWR test setup: Item 6: VSWR shall be less than 1.025 + .002 F (F in GHz). Item 16: VSWR shall be less than 1.025 + .002 F (F in GHz). Second step

20、of VSWR checkout procedure: VSWR shall be less than 1.080 + .005 F (F in GHz). Connector durability: 100 cycles, minimum at 12 cycles per minute maximum. The connector shall meet the mating characteristics and force to engage and disengage requirements. Contact resistance: In milliohms, maximum. Ini

21、tial After environmentCenter contact: Not applicable Not applicable Outer contact: 2.0 Not applicable Outer cable conductor to body: 0.5 1/ Not applicable Dielectric withstanding voltage at sea level: Method 301 of MIL-STD-202 Cables V rmsM17/133-RG405 1,000 M17/133-00001 through M17/133-00018 Vibra

22、tion, high frequency: Method 204, test condition D of MIL-STD-202, except the method of mounting shall be approved by the preparing activity. No discontinuity permitted. Shock (specified pulse): Method 213, test condition I of MIL-STD-202. Thermal shock: Method 107, test condition B of MIL-STD-202,

23、except test high temperature shall be +115C. Moisture resistance: Method 106 of MIL-STD-202. No measurements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Corona level: Altitude: 70,000 feet. Cables Volts (minimum)M17/133-RG405 25

24、0 M17/133-00001 through M17/133-00018 1/ Five milliohms is permissible for passivated steel bodied connectors only. SIZE CAGE CODE DWG NO. 037Z3 05011 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE7 Provided by IHSNot for ResaleNo reproduction or networking permitt

25、ed without license from IHS-,-,-RF high potential withstanding voltage: Frequency: 5 MHz to 7.5 MHz. Leakage current: Not applicable. Cables V rmsM17/133-RG405 670 M17/133-00001 through M17/133-00018 Cable retention force: The cable retention force shall be as specified in table III. TABLE III. Cabl

26、e retention force. Cable Pounds(minimum) Torque 1/ inch-ounce M17/133-RG405 M17/133-00001 through M17/133-00018 30 16 1/ Torque to be applied 4 inches maximum from the end of the connector. Reverse bend not applicable. Coupling mechanism retention force: 60 pounds minimum. RF leakage: -90 dB minimum

27、, tested at a frequency between 2 and 3 GHz. RF insertion loss: dB maximum = .03 x freq GHz. Test frequency at a frequency between .5 to 50 GHz. Part or Identifying Number (PIN): See table I. SIZE CAGE CODE DWG NO. 037Z3 05011 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A

28、 REVPAGE8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certif

29、icate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 05011ZSPA SF1603-6007 05011ZCGA 1603-400605011ZSPA-1 SF1603-600805011ZCGA-1 95077 1603-4007 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and test

30、s are met. Vendor CAGE Vendor Name and Number address95077 S/V Microwave, Inc. 2400 Centrepark West Dr. West Palm Beach, FL 33409 SIZE CAGE CODE DWG NO. 037Z3 05011 DEFENSE SUPPLY CENTER, COLUMBUS P. O. BOX 3990, COLUMBUS, OH 43218-3990 A REVPAGE9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-