DLA DSCC-DWG-05004 REV B-2010 CONNECTOR ELECTRICAL PLUG RADIO FREQUENCY SERIES ZMA PIN CONTACT FOR 141 AND 086 SEMIRIGID CABLE.pdf

《DLA DSCC-DWG-05004 REV B-2010 CONNECTOR ELECTRICAL PLUG RADIO FREQUENCY SERIES ZMA PIN CONTACT FOR 141 AND 086 SEMIRIGID CABLE.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-05004 REV B-2010 CONNECTOR ELECTRICAL PLUG RADIO FREQUENCY SERIES ZMA PIN CONTACT FOR 141 AND 086 SEMIRIGID CABLE.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Modify corona voltages for both cables. 12 July 2007 Lee Surowiec B Interface clarifications. Specify gold plating in accordance with MIL-DTL-45204. Add optional keying configurations. Editorial changes throughout. 1 April 2010 1 April 2010 Prepared in accor

2、dance with ASME Y14.100 Source Control Drawing REV PAGE REV STATUS OF PAGES REV B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 PMIC G PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 5 June 2007 CHECKED BY TITLE CONNECTOR, ELECTRICAL, PLUG, RADIO FREQ

3、UENCY, SERIES ZMA, PIN CONTACT, FOR .141 AND .086 SEMIRIGID CABLE Mary McWilliams APPROVED BY Lee Surowiec SIZE CAGE CODE DWG. NO. 05004 A 037Z3 REV B PAGE 1 OF 9 AMSC N/A 5935-E833-001 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY C

4、ENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 REV B PAGE 2 Dimension letter Dimensions Cable accommodation Minimum (mm) Maximum (mm) A .089 (2.26) .091 (2.31) M17/133-RG405 1/ .145 (3.68) .147 (3.73) M17/130-RG402 1/ B .762 (19.35) Reference C .485 (13.32) Maximum over

5、all diameter of connector 1/ All dash numbers for this specification sheet shall also apply. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All undimensioned pictorial configurations are for reference purposes only. FIGURE 1. General configuration. Provi

6、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 REV B PAGE 3 Dimension letter Dimensions Dimension letter Dimensions Minimum (mm) Maximum (mm) Minimum (mm) Maximu

7、m (mm) A .304 (7.72) .306 (7.77) H (see note 3) .130 (3.30) - B - .203 (5.16) J .000 (0.00) .010 (0.25) C (see note 3) - .163 (4.14) K (see note 3) .130 (3.30) - D .122 (3.10) .126 (3.20) M .0355 (0.908) .0370 (0.940) E .090 (2.29) .095 (2.41) N - .015 (0.38) F .020 (0.51) - P .060 (1.52) - G (see n

8、ote 3) .129 (3.28) R .015 (0.58) - NOTES: 1. Flared to meet the mechanical and electrical performance characteristics of the connector interface. 2. Dimension used for high voltage version in conjunction with a sealing gasket (not shown). 3. These are performance based dimensions. 4. Dimensions are

9、in inches. 5. Metric equivalents are given for information only. FIGURE 2. Interface dimensions, series ZMA pin. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05

10、004 REV B PAGE 4 NOTE: Angular tolerance is 0+1 FIGURE 3. Interface, series ZMA pin, coupling mechanism. B Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 RE

11、V B PAGE 5 Dimension letter Minimum (mm) Maximum (mm) A .060 (1.52) .066 (1.68) B .394 (10.01) .398 (10.11) C .057 (1.45) .070 (1.78) D .098 (2.49) .108 (2.74) E .049 (1.24) .056 (1.42) F .018 (0.46) .022 (0.56) G (Rad.) .026 (0.66) .036 0.91) NOTES: 1. Dimensions are in inches. 2. Metric equivalent

12、s are given for information only. FIGURE 3. Interface, series ZMA pin, coupling mechanism - Continued. MATERIALS: Connector body: Stainless steel in accordance with SAE-AMS5640. UNS S30300 (type I) condition A. Connector bodies shall be plated to a minimum gold thickness of 50 micro inches (1.27 m)

13、in accordance with MIL-DTL-45204, type II, grade C, class 1 (or equivalent as permitted by the qualification and preparing activities), over 50 micro inches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, appendix A, type 2.at least in the area of solder attachment. Contacts and lock ri

14、ng: Beryllium copper in accordance with ASTM B194, ASTM B196/B196M or ASTM B197/B197M. Gold plated (except locking ring) shall be plated to a minimum gold thickness of 50 micro inches (1.27 m) in accordance with MIL-DTL-45204, type II, grade C, class 1 (or equivalent as permitted by the qualificatio

15、n and preparing activities), over 50 micro inches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, appendix A, type 2. Insulator: PTFE in accordance with ASTM D4894 or ASTM D4895, or FEP in accordance with ASTM D2116. Gaskets: Silicone rubber in accordance with A-A-59588. ENGINEERING DAT

16、A: (Metric equivalents are in parentheses and given for general information only) Nominal impedance: 50 ohms. Frequency range: DC to 12.4 GHz. Voltage rating: 1/ Applies to all dash numbers in the referenced specification sheet. Temperature rating: -65C to +165C. Cable 1/ V rms, maximum (at sea leve

17、l) V rms, maximum (at 70,000 feet) M17/133-RG405 335 85 M17/130-RG402 500 125 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 REV B PAGE 6 REQUIREMENTS: Requ

18、irements of drawing 84148 are applicable. Dimensions and configuration: See figures 1, 2 and 3. Force to engage and disengage: Longitudinal force: 48 ounces, maximum. Torque: Not applicable. Mating characteristics: See figure 2 for dimensions. Test pin finish 16 micro inches (0.406 m). Outer contact

19、: Test ring ID: .182 inch (4.651 mm), maximum. Insertion force: 68 ounces, maximum. Contacts with slotted members: Shall contact a .182 inch (4.62 mm), minimum diameter ring within .031 inch (0.79 mm), of their tip ends. Coupling proof torque - Not applicable. Permeability: Applicable. Hermetic seal

20、: Not applicable. Leakage (pressurized connectors): Not applicable. Insulation resistance: In accordance with MIL-PRF-39012, 5,000 mega ohms, minimum. Center contact retention: Axial force: 6 pounds, minimum. Moisture resistance: In accordance with MIL-STD-202, method 106. No measurements at high hu

21、midity. Insulation resistance shall be 200 mega ohms minimum within 5 minutes of removal from humidity. Contact resistance (in milliohms, maximum): Initial After environment Center contact: 3 4 Outer contact: 2 N/A Dielectric withstanding voltage at sea level: 1/ Applies to all dash numbers in the r

22、eferenced specification sheet. Cable 1/ V rms, minimum M17/133-RG405 1,000 M17/130-RG402 1,500 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 REV B PAGE 7 T

23、hermal shock: In accordance with MIL-STD-202, method 107, test condition B. Salt spray: In accordance with MIL-PRF-39012. Vibration: In accordance with MIL-STD-202, method 204, test condition D. Shock: In accordance with MIL-STD-202, method 213, test condition I. Corona (70,000 feet): 1/ Applies to

24、all dash numbers in the referenced specification sheet. RF high potential withstanding voltage: Test frequency: 5 to 7.5 MHz. Leakage: Not applicable. 1/ Applies to all dash numbers in the referenced specification sheet. VSWR: 1.20:1, DC to 12.4 GHz (M17/133-RG405 and all dash numbers on the specifi

25、cation sheet). 1.18:1, DC to 12.4 GHz (M17/130-RG402 and all dash numbers on the specification sheet). RF leakage: -90 dB, minimum, at 2 GHz. Insertion loss: .03 F (F in GHz). Cable 1/ V rms, minimum M17/133-RG405 250 M17/130-RG402 375 Cable 1/ V rms, minimum (at sea level) M17/133-RG405 670 M17/130

26、-RG402 1,000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 REV B PAGE 8 Additive phase noise: Frequency of interest Allowed phase noise (dBc/Hz) max. 10 Hz

27、 -84 20 Hz -96 50 Hz -112 100 Hz -113 1 KHz -115 10 KHz -115 The phase noise through the Cabled Connector Under Test (CCUT) will be compared to the phase noise of the signal generator. The phase noise of the test system is measured and must be at least 10 dB below the test limits. The CCUT is connec

28、ted to the test system and the phase is adjusted for quadrature at the detector. The vibration table is energized and the detector is monitored during vibration over the frequency range of interest. Following completion of the vibration sequence the data is collected and plotted vs. frequency. Cable

29、 retention force: 1/ Applies to all dash numbers in the referenced specification sheet. 2/ Torque to be applied 4 inches maximum from the end of the connector. Reverse bend not applicable. Connector durability: 500 cycles minimum, at 12 cycles per minute maximum. Connectors must meet force to engage

30、 and disengage after cycling. Coupling mechanism retention force: Not applicable. Part or Identifying Number (PIN): PIN Keying configuration Cable accommodation 05004ZSG-1 A MIL-DTL-17/133 05004ZSG-2 A MIL-DTL-17/130 05004ASG-3 B MIL-DTL-17/133 05004ZSG-4 B MIL-DTL-17/130 05004ZSG-5 C MIL-DTL-17/133

31、 05004ZSG-6 C MIL-DTL-17/130 05004ZSG-7 D MIL-DTL-17/133 05004ZSG-8 D MIL-DTL-17/130 Cable 1/ Pounds (minimum) Torque 2/ Inch-ounce M17/133-RG405 30 16 M17/130-RG402 60 55 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBU

32、S COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05004 REV B PAGE 9 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been sub

33、mitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 05004ZSG-1 95077 SF8711-6012 05004ZSG-2 SF8711-6013 05004ZSG-3 SF8711-60085 05004ZSG-4 SF8711-60086 05004ZSG-5 SF8711-60087 05004ZSG-6 TSF8711-60088 05004ZSG-7 SF8711-60089 05004ZSG-8 SF8711-60090 1/ Parts must be purcha

34、sed to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor Name and number address 95077 S/V Microwave 2400 Centrepark West Dr. STE. 100 West Palm Beach, Fl 33409 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-