DLA DSCC-DWG-02006 REV B-2007 CAPACITORS FIXED TANTALUM CHIP《钽芯片固定电容器》.pdf

《DLA DSCC-DWG-02006 REV B-2007 CAPACITORS FIXED TANTALUM CHIP《钽芯片固定电容器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-02006 REV B-2007 CAPACITORS FIXED TANTALUM CHIP《钽芯片固定电容器》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Editorial changes, vendor part number changes. 4 February 2005 Kendall Cottingim B Optional surge current added 22 February 2007 Michael A Radecki Prepared in accordance with ASME-Y14.100 Selected item drawingREV PAGE REV PAGE REV B B B B B B B B REV STATUS

2、 OF PAGES PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Kenneth A. Bernier DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Kenneth A. Bernier APPROVED BY Kendall A. Cottongim TITLE CAPACITORS, FIXED, TANTALUM, CHIP SIZE A CODE IDENT. NO. 037Z3 DWG NO. 02006 Original date of drawing April 1, 200

3、3 REV B PAGE 1 OF 8 AMSC N/A 5910-E379 .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02006 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55365 describes

4、 the requirements for tantalum chip capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 02006 - XXX X | | _ Drawing Dash number Surge current option number (see table I) (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications. standard

5、s. and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (See 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-5536

6、5 - Capacitors, Fixed, Electrolytic (Tantalum), Chip, Nonestablished Reliability, Established Reliability, General Specification for. MIL-PRF-55365/4 - Capacitors, Chip, Fixed, Tantalum, Established Reliability, Styles CWR06 and CWR09. MIL-PRF-55365/11 - Capacitors, Chip, Fixed, Tantalum, Establishe

7、d Reliability, Styles CWR19 and CWR29. MIL-PRF-55365/8 - Capacitors, Chip, Fixed, Tantalum, Established Reliability, Styles CWR11. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/q

8、uicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document ta

9、kes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Changes to prod

10、uct. The manufacturer shall notify the procuring activity of any changes to the product that may affect the form, fit, or function of the device. Such notification shall be given prior to shipment of any device incorporating the identified change. 3.1.2 Termination finish. Termination finish shall b

11、e either letter H or letter K in accordance with MIL-PRF-55365. 3.1.3 Nickel barrier. When a nickel barrier is used on device terminations, the thickness shall be 100 -inch minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTE

12、R, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02006 REV B PAGE 3 Style Case L W H H1 (min) A W1 CWR29 X .258 -.285 (6.55 - 7.24) .198 - .228 (5.03 - 5.79) .093 - .123 (2.36 - 3.12) .048 (1.22) .042 - .057 (1.07 - 1.45) .115 - .125 (2.92 - 3.18) CWR29 F .205 - .235 (5.21 - 5.97) .120

13、 - .150 (3.05 - 3.81) .055 - .085 (1.40 - 2.16) .040 (1.02) .025 - .040 (0.64 -1.02) .125 - .135 (3.18 - 3.43) CWR29 D .135 - .165 (3.43 - 4.19) .085 - .115 (2.16 - 2.92) .035 - .065 (0.89 - 1.65) .030 (0.76) .025 - .040 (0.64 -1.02) .085 - .100 (2.16 - 2.54) CWR29 E .185 - .215 (4.70 - 5.46) .085 -

14、 .115 (2.16 - 2.92) .035 - .065 (0.89 - 1.65) .030 (0.76) .025 - .040 (0.64 -1.02) .085 - .100 (2.16 - 2.54) CWR09 or CWR 29 H .270 - .300 (6.86 - 7.62) .135 - .165 (3.43 - 4.19) .095 - .125 (2.41 - 3.18) .060 (1.52) .045 - .060 (1.14 - 1.52) .125 - .150 (3.18 - 3.81) CWR11 D .275 - .299 (6.99 - 7.5

15、9) .157 - .181 (3.99 - 4.60) .098 - .122 (2.49 - 3.10) .039 (0.99) .039 - .063 (0.99 - 1.60) .090 - .125 (2.29 - 3.18) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given in parenthesis for general information only. 3. These capacitors are designed for mounting by dip soldering, vapo

16、r phase, reflow soldering, or other conventional means. 4. Lead thickness: .0048 - .0052. Strip on top of part (not shown) indicates anode terminal. Termination finish in accordance with MIL-PRF-55365. FIGURE 1. Case dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or netwo

17、rking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02006 REV B PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be as specified in table I. 3.2.2 Minimum capacitance. When measured in acco

18、rdance with MIL-PRF-55365, except at a frequency of 100 kHz 5 kHz, the minimum capacitance shall be as specified in table I. 3.2.3 Capacitance tolerance. Capacitance tolerance shall be 10 percent. 3.2.4 Surge current. In accordance with MIL-PRF-55365 option A, B, or C. See table I for ordering. Surg

19、e Option C may be substituted for A or B. Surge Option B may be substituted for A. 3.2.5 Equivalent series resistance (ESR). In accordance with MIL-PRF-55365, for each of the following conditions: a. 100 kHz and +25C, b. 100 kHz and low test temperature when specified in table I (either -23C or -40C

20、), c. 120 Hz and low test temperature when specified in table I (either -23C or -40C). 3.3 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2 with the manufacturers name or CAGE code and date code marked on the unit packaging. It is not a requireme

21、nt to mark the individual parts. 3.4 Manufacturer eligibility. To be eligible for listing as a suggested source of supply, a manufacturer shall be listed on the MIL-PRF-55365 Qualified Products List for at least one part, or perform the group A and B inspections specified herein on a sample of parts

22、 agreed upon by the manufacturer and DSCC-VA. 3.5 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally prefe

23、rable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. The capacitor shall be uniform in quality and free from any defects that w

24、ill affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1/ Blank for Surge Current Option A, B for Surge Current Option B, or C for Surge Current Option C as specified in the part of identification number. ESR

25、max (Ohm) DC leakage (max) uA Dissipation factor (max) 120 Hz % Similar Style PIN 02006- Surge Current Option 1/ Case Code Cap. (nom.) 120Hz (F) Cap. (min.) 100KHz (F) Voltage (Vdc) 100 kHz25C 120 Hz -23C 100 kHz -23C 120 Hz-40C 100 kHz-40C 25C 85C 125C 25C 85C 125C -55C CWR29 001 * X 150 50 10 0.06

26、5 0.35 0.1 - - 15 225 375 10 12 15 CWR29 002 * X 15 9.5 35 0.190 - - 2.0 0.27 20 120 350 6 8 8 CWR29 003 * X 22 12 25 0.160 - - 1.4 0.22 11.6 174 289 6 8 8 CWR29 004 * X 10 3.5 40 0.600 3.5 0.78 - - 7.5 113 188 6 6 8 CWR29 005 * X 47 20 20 0.110 - 0.18 - - 9.5 141 235 6 8 8 CWR29 006 * X 33 15 25 0.

27、130 - 0.2 - - 12.4 186 310 6 8 8 CWR29 007 * X 220 70 6 0.080 - 0.2 - - 13.5 198 330 10 12 15 CWR29 008 * F 47 - 10 0.400 - - - - 5.0 50 60 6 8 10 CWR29 009 * D 4.7 2.5 15 1.0 5.5 2.0 - - 1.0 10 12 6 8 8 CWR29 010 * E 4.7 2.5 15 0.600 5.5 1.8 - - 1.0 10 12 6 8 8 CWR29 011 * F 22 12.1 15 0.400 2 0.7

28、- - 3.0 30 36 6 8 8 CWR09 012 * H 33 - 15 2.0 - - - - 5.0 50 60 6 8 8 CWR29 013 * H 47 - 20 0.110 - - - - 9.5 95 114 6 8 8 CWR29 014 * F 2.2 1.2 50 2.0 12 3.5 - - 2.0 20 24 6 8 8 CWR11 015 * F 3.3 1.5 35 1.5 - 2.3 - - 2.0 20 24 4 6 8 CWR29 016 * H 6.8 4.76 35 0.800 4.4 1.1 - - 2.5 25 30 6 8 8 TABLE

29、I. Electrical characteristics.DEFENSE SUPPLY CENTER COLUMBUS SIZE CODE IDENT NO DWG NO.COLUMBUS, OHIO A 037Z3 02006REV B PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3

30、 DWG NO. 02006 REV B PAGE 6 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the inspections, inspection conditions, sample sizes, and acce

31、ptance criteria for group A (Weibull distribution) and group C inspections (for ER capacitors) of MIL-PRF-55365, as modified herein. 4.2.2 Process monitors. The process monitors of MIL-PRF-55365 group A subgroup 2 shall be optional. 4.2.3 Group A inspection. Group A inspection of MIL-PRF-55365 with

32、the additions of table II shall be performed. 4.2.4 Group C testing. Group C inspection shall be performed per MIL-PRF-55365 with the following exceptions: a. Testing on a quarterly basis is not applicable. When a purchase order is accepted, Group C test samples shall be taken from the first availab

33、le products that pass Group A testing and is planned for delivery. b. The successful completion of Group C shall certify acceptable product quality for a one year period from the oldest lot date code test. c. All dash numbers shall receive separate Group C testing. Exceptions shall be listed below i

34、n paragraph 4.2.4.1 herein. d. The sample size for Group C testing shall be one-half the number listed in MIL-PRF-55365. The accept number shall remain the same. e. Exponential life testing is not applicable. 4.2.4.1 Generic Group C test data requirements. Generic Group C data is allowed provided th

35、at the voltage is the same or higher and the capacitance to volume ratio (power density) is similar or higher in the generic test data. No generic data on date codes older than one year from the date code on order will be allowed. The one year period does not apply when the design, material, constru

36、ction or processing of the part is significantly changed or if there are any quality problems. The manufacturer shall submit a cover letter with the group C data which explains the similarities and differences in the generic product and the customer part number. Customer acceptance of generic Group

37、C data does not relieve the manufacturer from meeting the requirements of Group C in case of dispute. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02006 REV B PAGE

38、7 The following generic part number substitutions have been reviewed and found acceptable. Other generic substitutions may be allowed without specific documentation herein, provided that the above rational is followed. Drawing Part Number Acceptable Generic Part Number Rational 02006-003 02006-006 s

39、ame voltage, same density 02006-009 02006-011 same voltage, same density 02006-010 02006-011 same voltage, same density 02006-015 CWR11MB335*B same voltage, higher density 02006-016 CWR29MB685*B same voltage, same density TABLE II. Group A inspection additions. Inspection Requirement paragraph Sampl

40、ing size Subgroup 1 Surge current 3.2.4 100% Subgroup 6 1/ Capacitance 3.2.2 10 samples ESR 3.2.5 0 failures 1/ Tests only required when a value is specified in table I herein. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or o

41、rder (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity with

42、in the Military Service or Defense Agency, or within the Military services System Commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This

43、section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Tantalum chip capacitors are intended to be used in thin or thick film hybrid circuits or surface mount applications where microcircuitry is indicated. 6.2 Ordering data. Th

44、e contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirement

45、s for packaging and packing. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Cent

46、er, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdla.mil also by telephone (614) 692-0563 or DSN 850-0563. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMB

47、US, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02006 REV B PAGE 8 6.6 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VA

48、T, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdla.mil also by telephone (614) 692-0563 or DSN 850-0563. 1/ PIN 2/ Vendors similar designation or type Vendor CAGE Vendors name and address 02006-001 02006-002 02006-003 02006-004 02006-005 02006-006 02006-007 02006-008 02006-009 02006-010 02006-011 02006-012 02006-013 02006-014 02006-015 02006-016 TAZX157K010LRLB0* TAZX156K035LRLB0* TAZX226K025LRLB0* TAZX106K040CRLB0* TAZX476K020LRLB0* TAZX