DLA DSCC-DWG-02002 REV B-2007 CAPACITORS FIXED TANTALUM CHIP《芯片是钽材料的固定电容器》.pdf

《DLA DSCC-DWG-02002 REV B-2007 CAPACITORS FIXED TANTALUM CHIP《芯片是钽材料的固定电容器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-02002 REV B-2007 CAPACITORS FIXED TANTALUM CHIP《芯片是钽材料的固定电容器》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Correct dash number references in 4.2.4c and update for current revision of MIL-PRF-55365. 3 August 2004 Kendall A. Cottongim B Correct dash number references in table I. 2 March 2007 Michael A. Radecki Prepared in accordance with ASME-Y14.5M Selected item

2、drawing REV PAGE REV B B B B B B REV STATUS OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Michael A. Radecki DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Michael A. Radecki APPROVED BY Kendall A. Cottongim TITLE CAPACITORS, FIXED, TANTALUM, CHIP SIZE A CODE IDENT. NO. 037Z3 DWG NO. 0200

3、2 Original date of drawing May 6, 2002 REV B PAGE 1 OF 6 AMSC N/A 5910-E378Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02002 REV B PAGE 2 1. SCOPE 1.1 Scope. This

4、drawing and MIL-PRF-55365 describes the requirements for tantalum chip capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 02002 - XXX X | | _ Drawing Dash number Surge current option number (see table I) (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government docume

5、nts. 2.1.1 Specifications. standards. and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (See 6.2). DEPARTMENT OF

6、DEFENSE SPECIFICATIONS MIL-PRF-55365 - Capacitors, Fixed, Electrolytic (Tantalum), Chip, Established Reliability and Nonestablished Reliability, General Specification for. MIL-PRF-55365/4 - Capacitors, Chip, Fixed, Tantalum, Polarized, Established Reliability and Nonestablished Reliability, Styles C

7、WR06 and CWR09. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Buildi

8、ng 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exem

9、ption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Changes to product. The manufacturer shall notify the procuring activity of any changes to the product that may affect the form, fi

10、t or function of the device. Such notification shall be given prior to shipment of any device incorporating the identified change. 3.1.2 Termination finish. Termination finish shall be either letter H or letter K per MIL-PRF-55365. 3.1.3 Nickel barrier. When a nickel barrier is used on device termin

11、ations, the thickness shall be 100 -inch minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02002 REV B PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equi

12、valents are given in parenthesis for general information only. 3. These capacitors are designed for mounting by dip soldering, vapor phase, reflow soldering, or other conventional means. 4. These capacitors will have a minimum of two bonding pads (top and bottom), on the major (width) dimension. FIG

13、URE 1. Case dimensions and configuration. TA N TA LUM W I RE N I BIDENTIFIES A NO DE ( + )TERM I N A LWHALDJJL W H (max.) A D (REF) J (max.) .265 - .281 (6.73 - 7.14) .225 - .245 (5.72 - 6.22) .130 (3.30) .020 - .060 (0.51 - 1.52) .243 (6.17) .004 (0.10) Provided by IHSNot for ResaleNo reproduction

14、or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02002 REV B PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be as specified in table I. 3.2.2 Minimum capacitance. When measured

15、 in accordance with MIL-PRF-55365, except at a frequency of 100KHz 5 KHz, the minimum capacitance shall be as specified in table I. 3.2.3 Capacitance tolerance. Capacitance tolerance shall be 10 percent. 3.2.4 Surge current. In accordance with MIL-PRF-55365 test option A, B, or C. See table I for or

16、dering. Surge Option C may be substituted for A or B. Surge Option B may be substituted for A. 3.2.5 Equivalent series resistance (ESR). In accordance with MIL-PRF-55365, for each of the following conditions: a. 100KHz and +25C, and b. 100KHz and low test temperature in table I (either -23C or -40C)

17、, and c. 120Hz and low test temperature in table I (either -23C or -40C). 3.3 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2 with the manufacturers name or CAGE code and date code marked on the unit packaging. Marking is not required on the ind

18、ividual parts. 3.4 Manufacturer eligibility. To be eligible for listing as a suggested source of supply, a manufacturer shall be listed on the MIL-PRF-55365 Qualified Products List for at least one part, or perform the group A and group C inspections specified herein on a sample of parts agreed upon

19、 by the manufacturer and DSCC-VA. 3.5 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materi

20、als should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect l

21、ife, serviceability, or appearance. TABLE I. Electrical characteristics. ESR max (Ohm) DC leakage (max) uA Dissipation factor (max) 120 Hz % PIN 02002- Surge Current Option 1/ Cap. (nom.) 120Hz (F) Cap. (min.) 100KHz (F) Voltage (Vdc) 100KHz25C 120Hz-23C 100KHz-23C 120Hz-40C100KHz-40C 25C85C 125C 25

22、C 85C125C-55C001 * 150 50 10 0.065 0.6 0.1 - - 15 225 375 10 12 15 002 * 15 9.5 35 0.190 - - 2.0 0.25 20 120 350 6 8 8 003 * 22 8.5 35 0.300 2.5 0.9 - - 10 100 120 6 8 8 004 * 10 3.5 40 0.600 5 1.8 - - 7.5 113 188 6 8 8 005 * 47 16 20 0.140 1.0 0.18 - - 9.5 141 235 6 8 8 1/ Blank for Surge Current O

23、ption A, B for Surge Current Option B, or C for Surge Current Option C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02002 REV B PAGE 5 4. VERIFICATION 4.1 Qualific

24、ation inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the inspections, inspection conditions, sample sizes, and acceptance criteria for group A (Weibull distribution) and g

25、roup C inspections (for ER capacitors) of MIL-PRF-55365, as modified herein. 4.2.2 Part Per Million (PPM) system. PPM of MIL-PRF-55365 group A shall be optional. 4.2.3 Group A inspection. Group A inspection of MIL-PRF-55365 with the additions of table II shall be performed. 4.2.4 Group C inspection.

26、 Group C inspection of MIL-PRF-55365 shall be performed with the following exceptions: a. Testing on a quarterly basis is not applicable. When a purchase order is accepted, group C test samples shall be taken from the first available product that passes group A inspection and is planned for delivery

27、. Suggested sources of supply may ship prior to completion of group C inspection. b. The successful completion of group C inspection shall certify acceptable quality for one calendar year. c. All dash numbers, with the exception of -002, shall receive separate group C inspections. Successful complet

28、ion of group C inspection for -003 shall be used to certify -002. d. The sample sizes for group C inspection shall be half the number listed in MIL-PRF-55365. The accept numbers shall remain the same. e. Exponential life testing is not applicable. TABLE II. Group A inspection additions. Inspection R

29、equirement paragraph Sampling size Subgroup 7 1/ Capacitance 3.2.2 10 samples ESR 3.2.5 0 failures 1/ Tests only required when a value is specified in table I herein. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see

30、6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Mil

31、itary Service or Defense Agency, or within the Military services System Commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for Re

32、saleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02002 REV B PAGE 6 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6

33、.1 Intended use. Tantalum chip capacitors are intended to be used in thin or thick film hybrid circuits or surface mount applications where microcircuitry is indicated. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for deli

34、very of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions is coordi

35、nated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus (DSCC), ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilt

36、erdscc.dla.mil, or by telephone (614) 692-0563 or DSN 850-0563. 6.4 Suggested sources of supply. A suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-

37、VAT, P. O. Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdscc.dla.mil, or by telephone (614) 692-0563 or DSN 850-0563. Surge current optionn 1/ PIN Vendors similar designation or type Vendor CAGE Vendors name and address Option A 02002-001 02002-002 02002-003 02002-004 02002-005 195

38、D157X9010N8T550 195D156X9035N8T550 195D226X9035N8T550 195D106X9040N8T550 195D476X9020N8T550 Option B 02002-001B 02002-002B 02002-003B 02002-004B 02002-005B 195D157X9010N8T55B 195D156X9035N8T55B 195D226X9035N8T55B 195D106X9040N8T55B 195D476X9020N8T55B Option C 02002-001C 02002-002C 02002-003C 02002-0

39、04C 02002-005C 195D157X9010N8T55C 195D156X9035N8T55C 195D226X9035N8T55C 195D106X9040N8T55C 195D476X9020N8T55C SH905 Vishay Israel LTD Industrial Park PO Box 87 Dimona 86000, Israel 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-