DLA DESC-DWG-87026 REV N-2013 RESISTOR NETWORK FIXED FILM 3-PIN.pdf
《DLA DESC-DWG-87026 REV N-2013 RESISTOR NETWORK FIXED FILM 3-PIN.pdf》由会员分享,可在线阅读,更多相关《DLA DESC-DWG-87026 REV N-2013 RESISTOR NETWORK FIXED FILM 3-PIN.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LT DESCRIPTION DATE APPROVED A Add new dash numbers 0012 through 0015. 3 MAR 88 David E. Moore B Add a new vendor. Editorial changes throughout. 27 JUN 88 David E. Moore C Add new dash numbers. Editorial changes throughout. 26 JUL 88 David E. Moore D Add new dash numbers. Editorial change
2、s throughout. 14 FEB 91 David E. Moore E Revise section 4. Editorial changes throughout. 20 APR 92 David E. Moore F Add new dash numbers 0025 through 0028. Editorial and policy changes throughout. 3 JUL 97 David E. Moore G CAGE code in footer of document shall remain 14933. Paragraph 6.5, delete ven
3、dor type numbers 301254 and 301257 and substitute 301257 and 301258. 10 SEP 97 David E. Moore H Add new source of supply and associated vendor similar PINs (see 6.5). 22 MAR 00 Kendall Cottongim J Add derating curve. Editorial changes throughout. 1 MAY 02 Kendall Cottongim K Changes in accordance wi
4、th NOR 5905-E408 14 MAY 02 Kendall Cottongim L Remove vendor plant address. Add pure tin prohibition paragraph. Figure 1 to be shown with standoff. Corrections to matched ratios in table I. Editorial changes throughout. 9 NOV 07 Michael Radecki M Add vendors. Add manufacturer eligibility and high po
5、wer pulse paragraphs. Editorial changes throughout. 16 DEC 09 Michael Radecki N Vendor address change. Editorial changes throughout. 17 May 13 Michael Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV N N N N N N N N PAGES 1 2 3 4 5 6 7 8 PMIC N/A Original date of drawing 6 Au
6、gust 1987 PREPARED BY Allan Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 CHECKED BY David Withrow TITLE RESISTOR NETWORK, FIXED, FILM, 3-PIN APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 87026 REV N PAGE 1 OF 8 AMSC N/A 5905-2012-E11 CURRENT DESIGN
7、 ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87026 REV N PAGE 2 1. SC
8、OPE 1.1 Scope. This drawing describes the requirements for a fixed, film, 3-pin resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 87026 - 0001 I I Drawing number (See table I) Dash number 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, st
9、andards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55182 -
10、Resistors, Fixed, Film, Nonestablished Reliability, Established Reliability, and Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualifie
11、d Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the DLA Document Services, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. Unless otherwise no
12、ted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence unless otherwise noted. Nothing in this document, however, supersedes applicable laws and
13、regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55182 and as specified herein. 3.2 Interface and physical dimension requirements. Resistors shall meet the interface and physical dim
14、ensions as specified in MIL-PRF-55182 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87026 REV N PAGE 3 NOTES: 1. Dimensions are in inches.
15、2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). FIGURE 1. Resistor network. Inches mm Inches mm Inches mm Inches mm Inches mm .003 0.07 .015 0.38 .050 1.27 .105 2.67 .320 8.13 .005 0.13 .025 0.64 .100 2.54 .302 7.67 .075 19.
16、05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87026 REV N PAGE 4 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance values shall be in accordance wit
17、h table I. 3.3.2 Resistance tolerance. Resistors are available in resistance tolerances as specified in table I. TABLE I. Resistance values. Dash number Resistance and tolerance Matched ratio Dash number Resistance and tolerance Matched ratio 0001 R1 = 10.0 k 1% R2 = 10.0 k 1% R1= 1.000 0.01% R20015
18、 R1 = 9.00 k 0.01% R2 = 1.00 k 0.01% R1 = 9.0000 0.01% R20002 R1 = 4.8148 k 1% R2 = 9.99 k 1% R1 = 0.48196 0.01% R20016 R1 = 10.0 k 1% R2 = 10.0 k 1% R1 = 1.0000 0.01% R20003 R1 = 10.0 k 1% R2 = 10.0 k 1% R1= 1.000 0.005% R20017 R1 = 20 k 1% R2 = 16.129 k 1% R1= 1.2400 0.01% R20004 R1 = 10.0 k 1% R2
19、 = 9.0 k 1% R1= 1.1111 0.005% R20018 R1 = 10 k 0.1% R2 = 1.931 k 0.1% R1 = 5.1787 0.05% R20005 R1 = 9.166 k 1% R2 = 10.0 k 1% R1= 0.9166 0.005% R20019 R1 = 10 k 0.1% R2 = 18.37 k 0.1% R1 = 0.54437 0.05% R20006 R1 = 10.0 k 1% R2 = 10.0 k 1% R1 = 1.000 0.03% R20020 R1 = 6.84 k 0.01% R2 = 3.16 k 0.01%
20、R1 = 2.1646 0.01% R20007 R1 = 20.0 k 1% R2 = 20.0 k 1% R1 = 1.000 0.03% R20021 R1 = 10.0 k 0.1% R2 = 20.0 k 0.1% R1= 0.500 0.1% R20008 R1 = 1.3 k 1% R2 = 1.3 k 1% R1 = 1.000 0.01% R20022 R1 = 2.5 k 0.01% R2 = 3.0 k 0.01% R1 = 0.8333 0.01% R20009 R1 = 20.0 k 1% R2 = 15.0 k 1% R2 = 0.7500 0.01% R10023
21、 R1 = 3.15 k 0.01% R2 = 3.15 k 0.01% R1 = 1.0 0.01% R20010 R1 = 5.0 k 1% R2 = 5.0 k 1% R1 = 1.000 0.01% R20024 R1 = 1.0 k 0.01% R2 = 9.0 k 0.01% R1 = 0.1111 0.01% R20011 R1 = 6.0 k 1% R2 = 3.0 k 1% R1 = 2.000 0.01% R20025 R1 = 10k 0.1% R2 = 1.93k 0.1% R1 = 5.1814 0.05% R20012 R1 = 10.0 k 0.01% R2 =
22、12.1 k 0.01% R1 = 0.8265 0.01% R20026 R1 = 5.6k 1.0% R2 = 13.68k 1.0% R2 = 2.4429 0.1% R10013 R1 = 8.75 k 0.01% R2 = 1.25 k 0.01% R1 = 7.0000 0.01% R20027 R1 = 2.49k 0.1% R2 = 4.87k 0.1% R1 = 0.5113 0.01% R20014 R1 = 8.00 k 0.01% R2 = 20.0 k 0.01% R1 = 0.4000 0.01% R20028 R1 = 4.02k 1.0% R2 = 4.02k
23、1.0% R1 = 1.00 1.0% R23.3.3 Power rating. The network shall have a power rating of 0.2 watt at +105OC divided proportionally between the resistors as the resistance is divided, derated in accordance with figure 2. 3.3.4 Temperature range. The operating temperature range shall be -55OC to +105OC. 3.3
24、.5 Resistance temperature characteristic. The resistance temperature characteristic shall be 5 parts per million (ppm)/OC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG N
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLADESCDWG87026REVN2013RESISTORNETWORKFIXEDFILM3PINPDF

链接地址:http://www.mydoc123.com/p-688349.html