DLA AN6248 REV 3-2011 PUMP-HYDRAULIC HAND TYPE 3000.pdf

《DLA AN6248 REV 3-2011 PUMP-HYDRAULIC HAND TYPE 3000.pdf》由会员分享，可在线阅读，更多相关《DLA AN6248 REV 3-2011 PUMP-HYDRAULIC HAND TYPE 3000.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 1650 AN6248 Rev 3 21 April 2011 SUPERSEDING AN6248 Rev 2 15 April 1981 DETAIL SPECIFICATION SHEET PUMP-HYDRAULIC HAND, TYPE 3000 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described her

2、ein shall consist of this specification sheet and MIL-DTL-5515. FIGURE 1. Hydraulic hand pump. C L SYMMETRICAL ABOUT C L 30 2 PIVOT MAY BE ANYWHERE IN SHADED AREA 1.125 C L 1.125 2.250 1.625 MAX DIA 1.031 1.125 2 +.000 - .010 2.250 WIDTH AT MOUNTING HOLES SUCTION PORT BOSS IN ACCORDANCE WITH “B“ (SE

3、E TABLE I) FOR SIZE “A“ (USE TABLE I) O.D. TUBE PROVIDE A BUILT IN CHECK VALVE AT THIS POINT. .510 .005 .020 MAX RAD 1.5 MAX DIA. DRILL .191 2.000 .010 .250 7 MAX .813 3.875 2.312 DISCHARGE PORT BOSS IN ACCORDANCE WITH “B“ BOSS FOR .250 OD TUBE (NO INTERNAL CHECK VALVE) EXTREME HIGH POSITION OF HAND

4、LE C L C L MID-POSITION OF HANDLE 35 1 30 2 4.312 MAX RAD 1.000 .001 DIA 1.531 MAX 3.125 MAX CLEARANCE ALLOWED FOR HANDLE MOVEMENT USING ANY PIVOT IN SHADED AREA .438 DRILL .257 2 HOLES FOR MOUNTING 2.75 .005 .5 .375 .625 EXTREME LOW POSITION OF HANDLE INCH-POUND Inactive for new design after 24 Jan

5、uary 1996. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN6248 Rev 3 2 Inches mm Inches mm .001 .005 .010 .020 .191 .203 .250 .257 .375 .438 .500 .510 .625 .813 0.03 0.13 0.25 0.51 4.85 5.16 6.35 6.53 9.53 11.13 12.70 12.95 15.88 20.65 1.000 1.031

6、 1.125 1.500 1.531 1.625 2.000 2.250 2.313 2.750 3.125 3.875 4.313 7.000 25.40 26.19 28.58 38.10 38.89 41.28 50.80 57.15 58.75 69.85 79.38 98.43 109.55 177.80 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances for three

7、place decimals .010 inch (0.25 mm), angles 0.5. FIGURE 1. Hydraulic hand pump - Continued. REQUIREMENTS Dimensions, see figure 1. Part or Identifying Number (PIN), see table I. TABLE I. PIN. AN PIN “A” “B” BOSS AN6248-1 3/8 .375 AND10050 AN6248-2 1/2 .5 AND10050 AN6248-3 1/2 .5 SAE-AS5202 AN6248-1 I

8、nactive for new design after 17 January 1949, use AN6248-2. AN6248-2 Inactive for new design after 18 April 1981, use AN6248-3. Interchangeability: AN6248-1 is not interchangeable with AN6248-2 or AN6248-3. AN6248-3 may be used in place of AN6248-2. AN6248-2 may not be used in place of AN6248-3. Cha

9、nges from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5515, this document references the following: AND10050 SAE-AS5202 Provided by IHSNot for Re

10、saleNo reproduction or networking permitted without license from IHS-,-,-AN6248 Rev 3 3 CONCLUDING MATERIAL Custodians: Preparing activity: Army AV DLA - CC Navy - AS Air Force - 99 (Project 1650-2010-007) DLA - CC Review activities: Army AT, CR4, GL Navy MC, SA, SH Air Force 11, 71 NOTE: The activi

11、ties listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-