DLA AN126821 THRU AN126880 REV 3-1986 STUD-STRAIGHT 625-11 X 625-18.pdf

《DLA AN126821 THRU AN126880 REV 3-1986 STUD-STRAIGHT 625-11 X 625-18.pdf》由会员分享，可在线阅读，更多相关《DLA AN126821 THRU AN126880 REV 3-1986 STUD-STRAIGHT 625-11 X 625-18.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、ANL26823 THRU AN32b880 REV 3 53 m 7777735 00003LiL T m THREAD A 1.250 1.312 1.562 (a) MAX FULL OR IMPERFEY:! THD= MIN FULL THD CHAMFER .O78x45O CHAMFER .062x4s0 SECTION THRU APPROX THREAD PROFILE BOTH THD SIZES .625-18UNP-3A STAUP PER UNDERSIZE AND OVERSIZE IIL-S-7742 IDENTIFICATION STAMP PER AM3280

2、0 .O10 MAX DEPTH B 1.000 1.000 1.000 AUS2800 .o10 MAX DEPTH UNDERSIZE AND OVERSIZE IDENTIFICATION D BEI DAF L - .375 .438 - 750 IP - - .o03 .620 -.625 .5682-.5692 .5687-.5702 .5610-.563O PART NUMBER AN126833 AN126839 AN126845 ICTIVE FOR DESI( STANDAF(D .620 -.625 .5712 - .5722 .5717-.5732 .5640-.566

3、0 PAAT NUMBER AN126834 AN126840 AN126846 +. 003 -620 -.625 .574?-.5752 -5747- .5762 .5670-.5690 PAW NUMBER AN126835 AN126841 AN126847 +. 006 .620 -.625 .5772-.5782 .5777-.5792 .5700- .5720 PART NUMBER AN126836 AN126842 AN126848 + . O09 629 -.634 5802-.5812 5730-*5750 ?ART NUMBER 5807-.5822 AN126037

4、AN126843 AN126849 +.o12 629 -.634 5832- .564 5837- -585 3760 - -578 ART HUMBE AN126830 AA126844 mi26850 AFTER 26 OCTOBER 1972. NO SUPERSEDING STANDARD. NOTE: PITCH DIAMETERS OF BOTH THREADED ENDS SHALL BE CONCENTRIC WITHIN .O06 FIR. (a) CROSS THREADING PERMISSABLE AT THREAD RUNOUTS ON SHORT STUDS. H

5、ATERIAL: STEEL AUS 6322 (AHS 6320 MATERIAL MAY ALSO BE USED FOR THESE PARTS UNTIL 1 JAN 1960) BARONESS: ROCKWELL C26-32. FINISH: CADMIUM PLATE AMs 2400. DIMENSIONS ARE AFTER PLATING EXCEPT WHERE SHOWN. SURFACE ROUGHNESS: AS291 KANUFACTURING SPECIFICATION AM9 7456. INSPECTION: ALL PARTS SHALL UNDERGO

6、 HAGNETIC INSPECTION IN ACCORDANCE WITH AHS2640. BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. DO NOT USE UNASSIGNED PART NUHBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE CAE. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIMENSIONS t.010. AN 126821 PA 11 AIR FORCE-NAVY AERONAUTICAL STANDARD I THRU AN 126880 I STUD - STRAIGHT, .625-11 X .625-18 CUST: AV, AS 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-