DLA AN107301 THRU AN107400 REV 3-1986 BOLT - CRES DRILLED HEX HEAD 6 HOLES 190-32.pdf

《DLA AN107301 THRU AN107400 REV 3-1986 BOLT - CRES DRILLED HEX HEAD 6 HOLES 190-32.pdf》由会员分享，可在线阅读，更多相关《DLA AN107301 THRU AN107400 REV 3-1986 BOLT - CRES DRILLED HEX HEAD 6 HOLES 190-32.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、- - ANL0730L THRU AN10Lt00 REV 3 53 II 9999935 0000283 O .O10 UAX K TO FULL THD .O58 TO POINT .o16 OR CHAHFE - SECTION TURU THREAD PROFILE .I90 (NO. 1Oj -32 NF - 3A SPEC UIL-6-7742 CSINK .90 TO .O60 DIA 6 HOLES SPACED AS SHOWN WITHIN .O20 OF TRUE POSITION THIS SURFACE HUST BE SQUARE WITH SHANK WITHI

2、N .O03 FULL INDICATOR READING LRILL .O469 CHAHFER 30 TO .375 DIA (OPPOSITE SIDE OPTIONAL) .500 .562 .62S .688 .750 .a12 :E 1 :E 1.000 .375 1.062 .438 1.125 500 I AN 101306 AN I O 7307 AN107308 AN101309 ANI07310 AN107311 AN1073 I2 AN107313 AN10731 4 AN IO7 3 15 AN107316 AN 1073 17 ANI07318 L - I. 18E

3、 1.25C 1.312 1.375 1.438 1.500 1.625 1.750 1 .875 2.000 2.125 2.250 2.375 2.500 - +. O00 ,562 AN107319 .625 AN101320 -688 AN107321 .750 AN107322 ,812 AN107323 .a75 AN101324 1.000 AN101325 1.125 AN101326 1.250 AN107327 I 1.315 AN107328 1.500 AN101329 1.625 AN101330 I 1.150 AN107331 1.875 AN107332 I (

4、a) THREAD TO HEAD. HAXIHUU TWO IHEERFECT THREADS, L K PART NO, +. O00 3.000 1 I AN107337 3.125 2.500 AN107331 3.250 AN107338 3 375 2.150 AN107339 3:500 1 2.875 1 AN107340 2.625 3.000 AN107541 L K t.000 - -060 .- PART NO NOTE: (I) SHANK SHALL BE STRAIGHT WITHIh .O04 FIR. PER INCH OP BOLT LENGTH, (2)

5、(3) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN .O11 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. UATERIAL: CORROSION RESISTANT STEEL - SEE

6、HANUFACTURING SPECIFICATION SURFACE ROUCBNESS: AS107 UANUFACTURING SPECIFICATION: AUS 1412 INSPECTION: BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIED. OIUEtSIONS IN INCHES. UNLESS OT?ERWISE SPECIFIED: TOLERENCES; LINEAR DIHENSIONS t.O1O. ANGULAR 1 ALL PARTS SHALL UNDERGO FLUORESCENT PENETR

7、ANT INSPECTION IN ACCORDANCE WITH AHS2645. DIHENSIONS t2*. DO NOT USE UNASSIGNED PART NUHBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENCINE ANU PROPELLER UTILITY PARTS COHHITTEE OF THE SAE. P.A. USAF - I1 Ither CUBL Navy-AS Army-AV AIR FORCE-NAVY AERONAUTICAL STANDARD AN I 07301 THRU BOLT - CREC DRILLED HEX HEAD, 6 HOLES, ,190-32 AN I07400 I I UYmnmEiT PmOYiOrnCP IMl-211.llylDy Projeet No.5306-1057 - THIS DOCUMENT CONTAINS - -( - PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-