DLA A-A-59935 1-2013 CONICAL SEALS CRUSH 37 DEGREE FLARED TUBE FITTTING ALUMINUM ALLOY.pdf

《DLA A-A-59935 1-2013 CONICAL SEALS CRUSH 37 DEGREE FLARED TUBE FITTTING ALUMINUM ALLOY.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59935 1-2013 CONICAL SEALS CRUSH 37 DEGREE FLARED TUBE FITTTING ALUMINUM ALLOY.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 INCHPOUND AA59935/1 2 October 2013 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET CONICAL SEALS, CRUSH, 37 DEGREE FLARED TUBE FITTTING, ALUMINUM ALLOY The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements

2、for procuring conical seal, crush, 37 degree flared tube fitting, aluminum alloy described herein shall consist of this document and the issue in effect of A-A-59935. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) uses a classification system which is incl

3、uded in the PIN as shown in the following example (see NOTES). AA59935/1 -04 A CID number Size code (see figure 1) Material and finish code (see table I) SALIENT CHARACTERISTICS. Interface and physical dimensions. Conical seals, crush, 37 degree flared tube fitting, aluminum alloy supplied to this C

4、ID specification sheet shall be as specified herein (see figure 1 and table I). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAI, P.O. Box 3990, Columbus OH 432180-3990, o

5、r fluidflowdla.mil. Since contact information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil/. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5

6、9935/1 2 Dash size code Tubing OD Ref. A +.005 -.000 B +.000 -.015 C +.005 -.000 D +.015 -.000 T inch -02 1/8 .240 .060 .245 .103 .005 -03 3/16 .302 .307 .166 -04 1/4 .354 .075 .359 .213 -05 5/16 .416 .421 .275 -06 3/8 .471 .476 .338 -08 1/2 .649 .095 .654 .446 .010 -10 5/8 .762 .105 .767 .562 -12 3

7、/4 .933 .938 .687 -16 1 1.183 .125 1.188 .936 -20 1-1/4 1.496 1.501 1.375 -24 1-1/2 1.745 1.750 1.410 -28 1-3/4 2.120 2.125 1.680 -32 2 2.370 2.375 1.913 -40 2 1/2 2.877 .055 2.882 2.500 .015 -44 2 3/4 3.127 3.125 2.742 -48 3 3.377 3.382 2.990 NOTES: 1. Dimensions are in inches. 2. Dimensioning and

8、tolerancing in accordance with ASME Y14.5. Unless otherwise specified, tolerances for decimals .005 inch (0.13 mm), angles .5. 3. Break sharp edges and remove burrs and slivers. 4. Surface texture shall be .005 inches in accordance with ASME B46.1. 5. These parts are soft and easily deformed dimensi

9、ons B, C, and D shall be verified by installing the seal on a standard fitting of the appropriate size. 6. An out-of-round-seal that does not interfere with installation shall not be cause for rejection. FIGURE 1. 37 flared crush seal. Provided by IHSNot for ResaleNo reproduction or networking permi

10、tted without license from IHS-,-,-A-A-59935/1 3 TABLE I. Material and finish code. Material and finish code Material and finish A Aluminum alloy, annealed, 1100 foil or sheet, condition “O” in accordance with QQ-A-1876, or ASTM B209, alloy 1100 AT Aluminum alloy, annealed, 1100 foil or sheet, condit

11、ion “O” in accordance with QQ-A-1876, or ASTM B209, alloy 1100. Tin plated in accordance with ASTM B545 or SAE-AMS2408 Tubing material and fluids or gases to be sealed, see table II. TABLE II. Tubing material and fluids or gases. Tubing and fitting material Assembly temperature range Fluids or gases

12、 Aluminum -420F to +275F (-251C to 135C) Helium Hydraulic oil Hydrogen Peroxide Hydrazine Liquid hydrogen Liquid Nitrogen Nitric acid Oxygen Pneumatics Udimethyldrazine Water Torque technique. These seals require a second torque technique; see A-A-59935 for torqueing procedure. NOTES. PIN. The PIN s

13、hould be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/1 4 Source of documents. FEDERAL SPECIF

14、ICATIONS QQ-A-1876 Aluminum Foil. COMMERCIAL ITEM DESCRIPTIONS A-A-59935 - Conical Seal, Crush, 37 Degree Flared Tube Fitting, General Requirements For (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the DLA Document Services Order Desk, 700 Robbins Avenue, Buil

15、ding 4D, Philadelphia, PA 191115094). Other Publications ASME INTERNATIONAL ASME Y14.5 - Dimensioning and Tolerancing ASME B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay) (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park A

16、venue, New York, NY 10016-5990.) ASTM INTERNATIONAL ASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate ASTM B545 - Standard Specification for Electrodeposited Coatings of Tin (Copies of these documents are available online at http:/www.astm.org or from the ASTM Intern

17、ational, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SAE INTERNATIONAL SAE- AMS2408 - Plating, Tin (Copies of these documents are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 inside USA

18、and Canada or 724-776-4970 outside USA, email at CustomerServicesae.org. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/1 5 Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinat

19、ed with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be consider

20、ed as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE number MFRs name and address 33447 SECO Seals Inc. 1370 Logan Ave. Unit K Costa Mesa, CA 92626 714-546-3778 E-mail: SECO 64162. Del Aerospace, Inc. 921 Mountain View Ave A Oxnard, CA

21、 93030-7227 E-mail: 66776 Alcoa Global Fasteners Inc. Div Rosan / Eagle Products DBA Alcoa Fastening Systems 800 S State College Blvd Fullerton, CA 92831-5334 01673 SPS Technologies LLC DBA Airdrome Precision Components Div SPS Technologies LLC 3251 E Airport WY Long Beach, CA 90806-2407 Part numbe

22、r (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system (see table III). Provided by IHSNot for ResaleNo reproduction or networking permitted wi

23、thout license from IHS-,-,-A-A-59935/1 6 TABLE III. P/N supersession data. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02A 33447 SECO7A-02 64162 DY90-A-2 -03A 33447 SECO7A-03 64162 DY90-A-3 -04A 33447 SECO7A-04 64162 DY90-A-4 -05A 33447 SECO7A-05 64162 DY90-A-5 -06

24、A 33447 SECO7A-06 64162 DY90-A-6 -08A 33447 SECO7A-08 64162 DY90-A-8 -10A 33447 SECO7A-10 64162 DY90-A-10 -12A 33447 SECO7A-12 64162 DY90-A-12 -16A 33447 SECO7A-16 64162 DY90-A-16 -20A 33447 SECO7A-20 64162 DY90-A-20 -24A 33447 SECO7A-24 64162 DY90-A-24 -28A 33447 SECO7A-28 64162 DY90-A-28 -32A 3344

25、7 SECO7A-32 64162 DY90-A-32 -40A 33447 SECO7A-40 64162 DY90-A-40 -44A 33447 SECO7A-44 64162 DY90-A-44 -48A 33447 SECO7A-48 64162 DY90-A-48 Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02A 66776 VSF1015A2 01673 AP50A2 -03A 66776 VSF1015A3 01673 AP50A3 -04A 66776 VSF1

26、015A4 01673 AP50A4 -05A 66776 VSF1015A5 01673 AP50A5 -06A 66776 VSF1015A6 01673 AP50A6 -08A 66776 VSF1015A8 01673 AP50A8 -10A 66776 VSF1015A10 01673 AP50A10 -12A 66776 VSF1015A12 01673 AP50A12 -16A 66776 VSF1015A16 01673 AP50A16 -20A 66776 VSF1015A20 01673 AP50A20 -24A 66776 VSF1015A24 01673 AP50A24

27、 -28A 66776 VSF1015A28 01673 AP50A28 -32A 66776 VSF1015A32 01673 AP50A32 -40A 66776 VSF1015A40 01673 AP50A40 -44A 66776 VSF1015A44 01673 AP50A44 -48A 66776 VSF1015A48 01673 AP50A48 See note at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

28、-,-,-A-A-59935/1 7 TABLE III. P/N supersession data - Continued. Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ -02AT 33447 SECO7AT-02 66776 VSF1015AT2 -03AT 33447 SECO7AT-03 66776 VSF1015AT3 -04AT 33447 SECO7AT-04 66776 VSF1015AT4 -05AT 33447 SECO7AT-05 66776 VSF1015A

29、T5 -06AT 33447 SECO7AT-06 66776 VSF1015AT6 -08AT 33447 SECO7AT-08 66776 VSF1015AT8 -10AT 33447 SECO7AT-10 66776 VSF1015AT10 -12AT 33447 SECO7AT-12 66776 VSF1015AT12 -16AT 33447 SECO7AT-16 66776 VSF1015AT16 -20AT 33447 SECO7AT-20 66776 VSF1015A20 -24AT 33447 SECO7AT-24 66776 VSF1015AT24 -28AT 33447 S

30、ECO7AT-28 66776 VSF1015AT28 -32AT 33447 SECO7AT-32 66776 VSF1015AT32 -40AT 33447 SECO7AT-40 66776 VSF1015AT40 -44AT 33447 SECO7AT-44 66776 VSF1015AT44 -48AT 33447 SECO7AT-48 66776 VSF1015AT48 Dash number (see table I) AA59935 MFRs CAGE MFRs P/N 1/ -02A 64162 DY90-AT-2 -03A 64162 DY90-AT-3 -04A 64162

31、 DY90-AT-4 -05A 64162 DY90-AT-5 -06A 64162 DY90-AT-6 -08A 64162 DY90-AT-8 -10A 64162 DY90-AT-10 -12A 64162 DY90-AT-12 -16A 64162 DY90-AT-16 -20A 64162 DY90-AT-20 -24A 64162 DY90-AT-24 -28A 64162 DY90-AT-28 -32A 64162 DY90-AT-32 -40A 64162 DY90-AT-40 -44A 64162 DY90-AT-44 -48A 64162 DY90-AT-48 1/ The

32、 manufacturers P/N shall not be used for procurement to the requirements of this specification sheet. At the time of preparation of this specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the

33、 marking paragraph of A-A-59935. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59935/1 8 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AV Navy - AS Air Force - 99 Preparing activity: DLA - CC DLA - CC Revi

34、ew activities: Army - AT, MI Project 4730-2013-076 Navy - MC, SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-