DLA A-A-59700 A-2008 COIL RF CHIP FIXED HIGH FREQUENCY MINIATURE SURFACE MOUNT.pdf

《DLA A-A-59700 A-2008 COIL RF CHIP FIXED HIGH FREQUENCY MINIATURE SURFACE MOUNT.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59700 A-2008 COIL RF CHIP FIXED HIGH FREQUENCY MINIATURE SURFACE MOUNT.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990, or email (transformersdla.mil). Since contact Informat

2、ion can change you may want to verify the currency of the address information using the ASSIST Online database at http:/assist.daps.dla.mil . AMSC N/A FSC 5950 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-59700A 9 May 2008 SUPERSEDING A-A-59700 1 O

3、ctober 2001 COMMERCIAL ITEM DESCRIPTION COIL, RF, CHIP, FIXED, HIGH FREQUENCY, MINIATURE, SURFACE MOUNT The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for a radio freque

4、ncy coil. Coils covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see 7.1). AA59700 - 001 F S CID number Dash number (see table

5、 I) Inductance Tolerance (see table II) Termination finish (see table III) 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Coils supplied to this CID shall be as specified herein. (see figure 1). 3.2. Electrical characteristics. The electrical characteristics shall be as specified

6、 in table I. 3.3 Weight. The weight shall be no greater than 0.5 gram maximum. 3.4 Operating temperature range. The operating temperature range is 40C to +125C. 3.5 Temperature rise. DC current rating for a 15C rise. 3.6 Altitude. The maximum altitude is 70,000 feet. 3.7 Marking. Inductors supplied

7、to this CID shall be marked with the manufacturers standard commercial PIN. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the ope

8、rational and maintenance requirements, and promotes economically advantageous life cycle costs. * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59700A 2 3.9 Workmanship. Coils shall be processed in such a manner as to be uniform in quality an

9、d shall be free from other defects that will affect life, serviceability, or appearance. Dimension INCHES MM A B C D E F G H .047 - .053 .075 - .085 .060 Max. .095 Max. .070 Max. .010 - .025 .017 - .023 .020 Ref. 1.19 1.35 2.41 2.67 1.52 Max. 2.41 Max. 1.78 Max. 0.25 0.64 0.43 0.58 0.508 Ref. NOTES:

10、 1. Dimensions are in Inches. 2. Metric equivalents are listed for general information only. FIGURE 1. Configuration and dimensions. * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59700A 3 TABLE I. Electrical characteristics. CID dash number A

11、A59700- Inductance(nH) Tolerance (%)Q Min SRF Min (MHz) DCR Max (OHMS) 1/ IDCMAX (mA) 001* 2.8 250 MHz 20, 10, 5 80 1500 MHz 7900 .06 800 002* 3.0 250 MHz 20, 10, 5 65 1500 MHz 7900 .06 800 003* 3.3 250 MHz 20, 10, 5 50 1500 MHz 7900 .08 600 004* 5.6 250 MHz 20, 10, 5 65 1000 MHz 5500 .08 600 005* 6

12、.8 250 MHz 20, 10, 5 50 1000 MHz 5500 .11 600 006* 7.5 250 MHz 20, 10, 5 50 1000 MHz 4500 .14 600 007* 8.2 250 MHz 20, 10, 5, 2 50 1000 MHz 4700 .12 600 008* 10 250 MHz 20, 10, 5, 2 60 500 MHz 4200 .10 600 009* 12 250 MHz 20, 10, 5, 2 50 500 MHz 4000 .15 600 010* 15 250 MHz 20, 10, 5, 2 50 500 MHz 3

13、400 .17 600 011* 18 250 MHz 20, 10, 5, 2 50 500 MHz 3300 .20 600 012* 22 250 MHz 20, 10, 5, 2 55 500 MHz 2600 .22 500 013* 24 250 MHz 20, 10, 5, 2 50 500 MHz 2000 .22 500 014* 27 250 MHz 20, 10, 5, 2 55 500 MHz 2500 .25 500 015* 33 250 MHz 20, 10, 5, 2, 1 60 500 MHz 2050 .27 500 016* 36 250 MHz 20,

14、10, 5, 2, 1 55 500 MHz 1700 .27 500 017* 39 250 MHz 20, 10, 5, 2, 1 60 500 MHz 2000 .29 500 018* 43 200 MHz 20, 10, 5, 2, 1 60 500 MHz 1650 .34 500 019* 47 200 MHz 20, 10, 5, 2, 1 60 500 MHz 1650 .31 500 020* 56 200 MHz 10, 5, 2, 1 60 500 MHz 1550 .34 500 021* 68 200 MHz 10, 5, 2, 1 60 500 MHz 1450

15、.38 500 022* 82 150 MHz 10, 5, 2, 1 65 500 MHz 1300 .42 400 023* 91 150 MHz 20, 10, 5, 2, 1 65 500 MHz 1200 .48 400 024* 100 150 MHz 10, 5, 2, 1 65 500 MHz 1200 .46 400 025* 110 150 MHz 20, 10, 5, 2 50 250 MHz 1000 .48 400 Provided by IHSNot for ResaleNo reproduction or networking permitted without

16、license from IHS-,-,-A-A-59700A 4 TABLE I. Electrical characteristics. - continued CID dash number AA59700- Inductance(nH) Tolerance (%) Q Min SRF Min (MHz) DCR Max (OHMS) 1/ IDCMAX (mA) 026* 120 150 MHz 10, 5, 2, 1 50 250 MHz 1100 .51 400 027* 150 100 MHz 10, 5, 2, 1 50 250 MHz 920 .56 400 028* 180

17、 100 MHz 10, 5, 2, 1 50 250 MHz 870 .64 400 029* 220 100 MHz 10, 5, 2 50 250 MHz 850 .70 400 030* 240 100 MHz 20, 10, 5, 2 44 250 MHz 690 1.0 350 031* 270 100 MHz 10, 5, 2 48 250 MHz 650 1.0 350 032* 330 100 MHz 10, 5, 2 48 250 MHz 600 1.4 310 033* 390 100 MHz 10, 5, 2 48 250 MHz 560 1.5 290 034* 47

18、0 50 MHz 10, 5 33 100 MHz 375 1.76 250 035* 560 25 MHz 10, 5 23 50 MHz 340 1.90 230 036* 680 25 MHz 10, 5 23 50 MHz 188 2.20 190 037* 820 25 MHz 10, 5 23 50 MHz 215 2.35 180 TABLE II. Inductance tolerances Code Tolerance (percentage) F G J K M 1 2 5 10 20 TABLE III. Termination finish. Code Terminat

19、ion finish L T S RoHS compliant, silver-palladium-glass-frit RoHS, tin-silver-copper (95.5/4/0.5) Tin-lead * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59700A 5 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovere

20、d materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings,

21、specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality

22、 of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over the past 2 years. 6. PACKAGING.

23、 Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally preferable mate

24、rials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals is available on their website at http:/

25、www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the following EPA site: http:/www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized or el

26、iminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE cod

27、e 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401

28、.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59700A 6 7.

29、6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of

30、 this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and address 02113 Coilcraft Inc 1102 Silver Lake Road Cary, Illinois 60013-1658 Phone number (847) 639-2361 Uniform

31、 Resource Locator (URL): 7.7 Part number (P/N) supersession data. This CID supersedes the following manufacturers P/Ns as shown. This information is being provided to assist in reducing proliferation in the government inventory system. TABLE II. P/N supersession data. 1/ CID dash number (see table

32、I) AA59700- Vendor commercial PIN CAGE 02113 2/ CID dash number (see table I) AA59700- Vendor commercial PIN CAGE 02113 2/ 001* 0805CS-020X* 020* 0805CS-560X* 002* 0805CS-3N0X* 021* 0805CS-680X* 003* 0805CS-030X* 022* 0805CS-820X* 004* 0805CS-050X* 023* 0805CS-910X* 005* 0805CS-060X* 024* 0805CS-101

33、X* 006* 0805CS-070X* 025* 0805CS-111X* 007* 0805CS-080X* 026* 0805CS-121X* 008* 0805CS-100X* 027* 0805CS-151X* 009* 0805CS-120X* 028* 0805CS-181X* 010* 0805CS-150X* 029* 0805CS-221X* 011* 0805CS-180X* 030* 0805CS-241X* 012* 0805CS-220X* 031* 0805CS-271X* 013* 0805CS-240X* 032* 0805CS-331X* 014* 0805

34、CS-270X* 033* 0805CS-391X* 015* 0805CS-330X* 034* 0805CS-471X* 016* 0805CS-360X* 035* 0805CS-561X* 017* 0805CS-390X* 036* 0805CS-681X* 018* 0805CS-430X* 037* 0805CS-821X* 019* 0805CS-470X* 1/ When “*“ is used for coded values, its the contractors responsibility to select those options allowed by the

35、 CID. 2/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. Provided by IHSNot for ResaleNo reproduction or networking permit

36、ted without license from IHS-,-,-A-A-59700A 7 7.8 Government users. To acquire information on obtaining these coils from the Government inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-FMTE, Post Office Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7727. 7.9 Changes

37、from previous issue. The margins of this CID are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to

38、 evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Custodians: Navy - EC Preparing Activity: DLA - CC DLA - CC Project 5950-2008

39、-063 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-