DLA A-A-59698 B-2013 COIL RF CHIP FIXED LOW DCR SURFACE MOUNT.pdf

《DLA A-A-59698 B-2013 COIL RF CHIP FIXED LOW DCR SURFACE MOUNT.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59698 B-2013 COIL RF CHIP FIXED LOW DCR SURFACE MOUNT.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be addressed to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O. Box 3990, Columbus OH 43218-3990, or email (transformersdla.mil ). Since contact information can chan

2、ge you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 5950 A-A-59698B 5 December 2013 SUPERSEDING A-A-59698A 9 May 2008 COMMERCIAL ITEM DESCRIPTION COIL, RF, CHIP, FIXED, LOW DCR, SURFACE MOUNT The General Services A

3、dministration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for a radio frequency coil. Coils covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This CID uses a cl

4、assification system which is included in the Part Identification Number (PIN) as shown in the following example (see 7.1). AA59698 - 001 F T CID number Dash number (see table I) Inductance Tolerance (see table II) (Optional) Termination finish (see table III) 3. SALIENT CHARACTERISTICS. 3.1 Interfac

5、e and physical dimensions. Coils supplied to this CID shall be as specified herein. (see figure 1). 3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I. 3.3 Weight. The weight shall be no greater than 0.5 gram maximum. 3.4 Operating temperature range. The

6、 operating temperature range is 40C to +85C. 3.5 Temperature rise. DC current rating for a 15C rise. 3.6 Altitude. The maximum altitude is 70,000 feet. 3.7 Marking. Inductors supplied to this CID shall be marked with the manufacturers standard commercial PIN. 3.8 Pure tin. The use of pure tin, as an

7、 underplate or final finish is prohibited both internally and externally. Tin content of transformer components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled,

8、 recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. Inductors shall be processed in such

9、a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59698B 2 Dimension INCHES MM A B C D E F G H .076 - .084 .09

10、5 - .105 .080 Max. .115 Max. .110 Max. .010 - .025 .015 - .025 .020 Ref. 1.93 - 2.13 2.41 - 2.67 2.03 Max. 2.92 Max. 2.79 Max. 0.254 - 0.64 0.381 - 0.64 0.508 Ref NOTES: 1. Dimensions are in Inches. 2. Metric equivalents are listed for general information only. FIGURE 1. Configuration and dimensions

11、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59698B 3 TABLE I. Electrical characteristics. CID dash number AA59698- Inductance (H) ( 7.9 MHz) Tolerance(%) Q min SRF min (MHz)DCR Max (Ohms) 1/ IDCMax(mA) 001* 1.2 7.9 MHz 5 37 50 MHz 210 .68 6

12、50 002* 1.5 7.9 MHz 5 37 50 MHz 190 .76 630 003* 1.8 7.9 MHz 5 37 50 MHz 170 .84 600 004* 2.2 7.9 MHz 5 37 50 MHz 150 1.10 520 005* 2.7 7.9 MHz 5 37 50 MHz 135 1.28 490 006* 3.3 7.9 MHz 5 37 50 MHz 120 1.46 450 007* 3.9 7.9 MHz 5 37 7.9 MHz 105 1.56 420 008* 4.7 7.9 MHz 5 32 7.9 MHz 90 1.68 400 009*

13、 5.6 7.9 MHz 5 37 7.9 MHz 80 1.82 380 010* 6.8 7.9 MHz 5 37 7.9 MHz 70 2.00 360 011* 8.2 7.9 MHz 5 37 7.9 MHz 65 2.65 330 012* 10.0 7.9 MHz 5 37 7.9 MHz 60 2.95 300 013* 1.0 7.9 MHz 5 48 50 MHz 230 0.62 700 014* 4.3 7.9 MHz 5 30 7.9 MHz 85 1.70 400 015* 5.0 7.9 MHz 5 25 7.9 MHz 30 2.20 360 016* 6.2

14、7.9 MHz 5 32 7.9 MHz 75 2.50 330 017* 9.1 7.9 MHz 5 37 7.9 MHz 57 2.90 310 018* 12 2.5 MHz 5 28 2.5 MHz 38 3.30 290 019* 15 2.5 MHz 5 34 2.5 MHz 30 3.70 280 020* 22 2.5 MHz 5 20 2.5 MHz 22 6.14 270 021* 27 2.5 MHz 5 24 2.5 MHz 12 6.45 210 022* 33 2.5 MHz 5 22 2.5 MHz 19 7.00 200 023* 39 2.5 MHz 5 33

15、 2.5 MHz 26 10.0 170 024* 47 2.5 MHz 5 20 2.5 MHz 12 10.7 160 025* 56 2.5 MHz 5 20 2.5 MHz 8.0 10.0 170 026* 68 2.5 MHz 5 14 .79 MHz 5.7 13.5 145 027* 100 2.5 MHz 5 13 .79 MHz 4.5 20.5 120 1/ DC current rating for a 15C rise. TABLE II. Inductance tolerances Code Tolerance (percentage) J 5 Provided b

16、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59698B 4 TABLE III. Termination finish. Code Termination finishLeave blank L T Tin-lead RoHS compliant, silver-palladium-platinum-glass-frit RoHS, tin-silver-copper (95.5/4/0.5) 4. REGULATORY REQUIREMENTS. Th

17、e offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of

18、 this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market accepta

19、nce criteria are necessary to document the quality of the product to be provided under this CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company must have sold 1,000 units meeting this CID in the commercia

20、l marketplace over the past 2 years. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally pr

21、eferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of

22、 chemicals is available on their website at http:/www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the following EPA site: http:/www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of t

23、he materials on the list should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these inductors to DSCC under the Military Parts Control A

24、dvisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (Copies of these documents are available online at www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 7

25、32 North Capital Street, NW, Washington D.C. 20401.) 7.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typi

26、cal operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter

27、, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59698B 5 7.6 Ordering data. The contract or order should specify the following: a. CID document number, revision,

28、and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.7 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacture

29、rs were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and address 02113 Coilcraft Inc 1102 S

30、ilver Lake Road Cary, Illinois 60013-1658 Phone number (847) 639-2361 Uniform Resource Locator (URL): 7.8 Part number (P/N) supersession data. This CID supersedes the following manufacturers P/Ns as shown. This information is being provided to assist in reducing proliferation in the government inve

31、ntory system. TABLE III. P/N supersession data. 1/ CID dash number (see table I) AA59698- Vendor commercial PIN 2/ CAGE 02113 CID dash number (see table I) AA59698- Vendor commercial PIN 2/ CAGE 02113 001* 1008LS-122XJL* 015* 1008LS-502XJL*002* 1008LS-152XJL* 016* 1008LS-622XJL* 003* 1008LS-182XJL*

32、017* 1008LS-912XJL*004* 1008LS-222XJL* 018* 1008LS-123XJL* 005* 1008LS-272XJL* 019* 1008LS-153XJL*006* 1008LS-332XJL* 020* 1008LS-223XJL* 007* 1008LS-392XJL* 021* 1008LS-273XJL*008* 1008LS-472XJL* 022* 1008LS-333XJL* 009* 1008LS-562XJL* 023* 1008LS-393XJL*010* 1008LS-682XJL* 024* 1008LS-473XJL* 011*

33、 1008LS-822XJL* 025* 1008LS-563XJL*012* 1008LS-103XJL* 026* 1008LS-683XJL* 013* 1008LS-102XJL* 027* 1008LS-104XJL*014* 1008LS-432XJL* 1/ When “*“ is used for coded values, its the contractors responsibility to select those options allowed by the CID. 2/ The manufacturers P/N shall not be used for pr

34、ocurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59698B 6 7.9 Gover

35、nment users. To acquire information on obtaining these coils from the Government inventory system, contact DLA Land and Maritime, ATTN: DSCC-FMTC, Post Office Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-7727. 7.10 Changes from previous issue. The margins of this CID are marked with ast

36、erisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire

37、content irrespective of the marginal notations and relationship to the last previous issue. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Custodians: Navy - EC Preparing Activity: DLA - CC DLA - CC Project 5950-2013-013 NOTE: The activities listed above were interested in this d

38、ocument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-