DLA A-A-59590 22 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 500 X 450 INCH BODY SIZE WITH VISUAL LOCK INDICATION.pdf

《DLA A-A-59590 22 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 500 X 450 INCH BODY SIZE WITH VISUAL LOCK INDICATION.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59590 22 B-2013 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 500 X 450 INCH BODY SIZE WITH VISUAL LOCK INDICATION.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA59590/22B 22 March 2013 SUPERSEDING AA59590/22A 11 September 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE .500 X .450 INCH BODY SIZE, WITH VISUAL LOCK INDICATION The General Services Administration has author

2、ized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item

3、description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59590 CID number /22 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) * Configuration (s

4、ee table II) Example: AA59590/22ET48E is the PIN for a nickel plated, 4.8 inches (122 mm) long card holder with a visual lock indication and a screw self-locking element. The card holder also features two tapped 0-80 UNF mounting holes for use with fasteners. SALIENT CHARACTERISTICS. Performance. Ca

5、rd holders shall hold the circuit card assembly firmly in its installed position and prevent loosening or movement as a result of shock and vibration. The card holder shall also provide a thermal transfer path from the circuit card assembly to the cold plate or heat sink surfaces. Card holders shall

6、 have a visual indicator to show when the assembly is in its relaxed (unlocked) state. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4 and table I) and meet the general requirements of CID AA59590. Mate

7、rial. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Actuating screw hex drive socket. The dimension for hex drive socket shall be .156 inch (3.96 mm) for mounting options “J“, “N“, “T“ and “V“. The dimension for hex drive socket shall be a metric dime

8、nsion of 2.5 mm (.098 inch) across flats for mounting option “G“. Cold plate dimensions. Recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .525 inch (13.3 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). AMSC

9、N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/22B 2 Inches mm Inches mm Inches mm Inches mm Inches mm .20 .25 5.1 6.4 .260 .270 6.60 6.86 .27 .325 6.9 8.26 .39 .56 9.9 14.2 .70 17.8 NOTES: 1. Dimensions are in inches. Millimeter

10、s are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex drive soc

11、ket shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions, basic configuration. Nominal installation t

12、orque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 31 inch-pounds (3.5 N-m) for assemblies using no options or option “W“ and 34 to 36 inch-pounds (3.8 to 4.1 N-m) for assemblies using options “D“ or “E“. Provided by

13、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/22B 3 Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card holder assembly is in its relaxed (unlocked) state. When the card holder assembly is in the rela

14、xed state, the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened so that the assembly is in the expanded (locked) position, this red band shall be concealed. FIGURE 2. Visual lock indicator details. Finish. Th

15、e finish designator shall be as specified in AA59590. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be a

16、s specified in AA59590. Except when using mounting option “N“, two mounting holes are required on the card holders. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UN

17、C 2B holes), or “G“ (tapped M2.5 x.45 metric holes). See figure 1 and table I for mounting hole spacing requirements. Card holders using mounting option “J“ may be shipped unassembled. Counterbore holes (for rivet mounting). The holes used for rivet mounting shall be .136 inch (3.45 mm) diameter, co

18、untersunk 100 degrees by .190/.200 inch (4.83/5.08 mm) diameter through holes with an access/clearance counterbore of .190/.200 inch (4.83/5.08 mm) diameter by .390 inch (9.91 mm) deep. Rivets. This card holder uses rivet type B as specified in AA59590 when rivet mounting is used. Length, expanded,

19、and relaxed dimensions. The length designator shall be as specified in AA59590 and the lengths available for this CID specification sheet are listed in table I. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE I. Assembly dimensions (see figure 1). 1/ PIN length

20、designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “B“ .03 (0.8 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) 2.30 (58.4 mm) .90 (22.9 mm) 33 3.3 (84 mm) 2.80 (71.1 mm) 1.40 (35.6 mm) 38 3.8 (97 mm) 3.30 (83.8 mm) 1.90 (48.3 mm) 43 4.3 (109 mm) 3.80 (96.5 mm) 2.40 (61.0 mm) 48 4.8 (122 mm) 4.30

21、(109.2 mm) 2.90 (73.7 mm) 53 5.3 (135 mm) 4.80 (121.9 mm) 3.40 (86.4 mm) 58 5.8 (147 mm) 5.30 (134.6 mm) 3.90 (99.1 mm) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

22、se from IHS-,-,-AA59590/22B 4 Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. The correct PIN configuration identifier for each option is list

23、ed in table II. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Configuration. Configuration Applicable figures Hardware options 1 and 2 No changes from basic configuration W 1, 2 and 3 Lockwasher and flat washer E 1, 2

24、and 4 Screw self-locking element D 1, 2, 3 and 4 Lockwasher, flat washer, and screw self-locking element Lockwasher and flat washer (see figure 3). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly fro

25、m shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The use of a screw self-locking element on the screw will provide

26、a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classification and notes). F

27、IGURE 4. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classification and notes).Provided by IHSNot for ResaleNo reproduct

28、ion or networking permitted without license from IHS-,-,-AA59590/22B 5 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA595

29、90 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philad

30、elphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet prepar

31、ation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown

32、.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 American Circuit Card R

33、etainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in

34、table III are only for length designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or

35、networking permitted without license from IHS-,-,-AA59590/22B 6 TABLE III. Commercial part number supersession data. PIN designator AA59590/22 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28 VA2552.80H 3500VBA2.80H BN28 VA2552.80 3500VBA2.80 BT28 VA2552.80T0 3500VBA2.8

36、0T0 BV28 VA2552.80T2 3500VBA2.80T2 BG28 MVA2552.80TM2.5 3500MVBA2.80TM2.5 BJ28W WVA2552.80H 3500VWBA2.80H BN28W WVA2552.80 3500VWBA2.80 BT28W WVA2552.80T0 3500VWBA2.80T0 BV28W WVA2552.80T2 3500VWBA2.80T2 BG28W MWVA2552.80TM2.5 3500MVWBA2.80TM2.5 BJ28E VA2552.80HL 3500VBA2.80HL BN28E VA2552.80L 3500V

37、BA2.80L BT28E VA2552.80T0L 3500VBA2.80T0L BV28E VA2552.80T2L 3500VBA2.80T2L BG28E MVA2552.80TM2.5L 3500MVBA2.80TM2.5L BJ28D WVA2552.80HL 3500VWBA2.80HL BN28D WVA2552.80L 3500VWBA2.80L BT28D WVA2552.80T0L 3500VWBA2.80T0L BV28D WVA2552.80T2L 3500VWBA2.80T2L BG28D MWVA2552.80TM2.5L 3500MVWBA2.80TM2.5L

38、CJ28 V2552.80H 3500VCG2.80H CN28 V2552.80 3500VCG2.80 CT28 V2552.80T0 3500VCG2.80T0 CV28 V2552.80T2 3500VCG2.80T2 CG28 MV2552.80TM2.5 3500MVCG2.80TM2.5 CJ28W WV2552.80H 3500VWCG2.80H CN28W WV2552.80 3500VWCG2.80 CT28W WV2552.80T0 3500VWCG2.80T0 CV28W WV2552.80T2 3500VWCG2.80T2 CG28W MWV2552.80TM2.5

39、3500MVWCG2.80TM2.5 See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/22B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/22 Vendor similar designator or type part number 1/ 2

40、/ CAGE 61081 CAGE 5BG68 CJ28E V2552.80HL 3500VCG2.80HL CN28E V2552.80L 3500VCG2.80L CT28E V2552.80T0L 3500VCG2.80T0L CV28E V2552.80T2L 3500VCG2.80T2L CG28E MV2552.80TM2.5L 3500MVCG2.80TM2.5L CJ28D WV2552.80HL 3500VWCG2.80HL CN28D WV2552.80L 3500VWCG2.80L CT28D WV2552.80T0L 3500VWCG2.80T0L CV28D WV25

41、52.80T2L 3500VWCG2.80T2L CG28D MWV2552.80TM2.5L 3500MVWCG2.80TM2.5L EJ28 VEN2552.80H 3500VEN2.80H EN28 VEN2552.80 3500VEN2.80 ET28 VEN2552.80T0 3500VEN2.80T0 EV28 VEN2552.80T2 3500VEN2.80T2 EG28 MVEN2552.80TM2.5L 3500MVEN2.80TM2.5 EJ28W WVEN2552.80H 3500VWEN2.80H EN28W WVEN2552.80 3500VWEN2.80 ET28W

42、 WVEN2552.80T0 3500VWEN2.80T0 EV28W WVEN2552.80T2 3500VWEN2.80T2 EG28W MWVEN2552.80TM2.5 3500MVWEN2.80TM2.5 EJ28E VEN2552.80HL 3500VEN2.80HL EN28E VEN2552.80L 3500VEN2.80L ET28E VEN2552.80T0L 3500VEN2.80T0L EV28E VEN2552.80T2L 3500VEN2.80T2L EG28E MVEN2552.80TM2.5L 3500MVEN2.80TM2.5L EJ28D WVEN2552.

43、80HL 3500VWEN2.80HL EN28D WVEN2552.80L 3500VWEN2.80L ET28D WVEN2552.80T0L 3500VWEN2.80T0L EV28D WVEN2552.80T2L 3500VWEN2.80T2L EG28D MWVEN2552.80TM2.5L 3500MVWEN2.80TM2.5L See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

44、-AA59590/22B 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/22 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 HJ28 VHA2552.80H 3500VBH2.80H HN28 VHA2552.80 3500VBH2.80 HT28 VHA2552.80T0 3500VBH2.80T0 HV28 VHA2552.80T2 3500VBH2.80T2

45、HG28 MVHA2552.80TM2.5L 3500MVBH2.80TM2.5 HJ28W WVHA2552.80H 3500VWBH2.80H HN28W WVHA2552.80 3500VWBH2.80 HT28W WVHA2552.80T0 3500VWBH2.80T0 HV28W WVHA2552.80T2 3500VWBH2.80T2 HG28W MWVHA2552.80TM2.5L 3500MVWBH2.80TM2.5 HJ28E VHA2552.80HL 3500VBH2.80HL HN28E VHA2552.80L 3500VBH2.80L HT28E VHA2552.80T

46、0L 3500VBH2.80T0L HV28E VHA2552.80T2L 3500VBH2.80T2L HG28E VMHA2552.80TM2.5L 3500MVBH2.80TM2.5 HJ28D WVHA2552.80HL 3500VWBH2.80HL HN28D WVHA2552.80L 3500VWBH2.80L HT28D WVHA2552.80T0L 3500VWBH2.80T0L HV28D WVHA2552.80T2LR 3500VWBH2.80T2L HG28D MWVHA2552.80TM2.5L 3500MVWBH2.80TM2.5L RJ28 VR2552.80H 3

47、500VCC2.80H RN28 VR2552.80 3500VCC2.80 RT28 VR2552.80T0 3500VCC2.80T0 RV28 VR2552.80T2 3500VCC2.80T2 RG28 MVR2552.80TM2.5L 3500MVCC2.80TM2.5 RJ28W WVR2552.80H 3500VWCC2.80H RN28W WVR2552.80 3500VWCC2.80 RT28W WVR2552.80T0 3500VWCC2.80T0 RV28W WVR2552.80T2 3500VWCC2.80T2 RG28W MWVR2552.80TM2.5L 3500MVWCC2.80TM2.5 See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/22B 9 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/22 Vendor simi