DLA A-A-59590 17 B-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 260 X 260 INCH BODY SIZE.pdf

《DLA A-A-59590 17 B-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 260 X 260 INCH BODY SIZE.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59590 17 B-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 3 PIECE SCREW ACTUATED DRIVE 260 X 260 INCH BODY SIZE.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA59590/17B 17 June 2012 SUPERSEDING AA59590/17A 23 June 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .260 X .260 INCH BODY SIZE The General Services Administration has authorized the use of this commercial it

2、em description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sh

3、eet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /17 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) * Configuration Example: AA59590/17EV38D is the PIN for a n

4、ickel plated, 2.8 inches (97 mm) long card holder with a flat washer, lockwasher, and screw self-locking element. The card holder also features two tapped mounting holes for use with metric M2.5 x 0.45 fasteners. SALIENT CHARACTERISTICS. Performance. Card holders shall hold the circuit card assembly

5、 firmly in its installed position and prevent loosening or movement as a result shock and vibration. It shall also provide a thermal transfer path from the circuit card assembly to the cold plate or heat sink surfaces. Interface and physical dimensions. The card holders supplied to this CID specific

6、ation sheet shall be as specified herein (see figures 1, 2, 3, and table I) and meet the general requirements of CID AA59590. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Actuating screw hex drive socket. The dimension for hex drive socket

7、shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“ and “V“. The dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats for mounting option “G“. Cold plate dimensions. The recommend cold plate slot width to accommodate the circuit card assembly with

8、 attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 10 inch-pounds

9、 (1.1 N-m) for assemblies using no options or option “W“ and 12 inch-pounds (1.4 N-m) for assemblies using options “D“ or “E“. AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/17B 2 Inches mm Inches mm Inches mm Inches mm .07

10、.13 1.8 3.3 .20 .25 5.1 6.4 .260 .270 6.6 6.86 .325 .70 8.26 17.8 NOTES: 1. Dimensions are in inches. Millimeters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The t

11、olerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex drive socket shall be .094 inch (2.39 mm) for mounting options “J“, “N“, “T“ and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 2.5 mm (.098 inch) across flats

12、for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions, basic configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/17B 3 Finish. The finish designator shall be as specified in AA59590. The finishes available for this CID

13、 specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless nickel), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. Except when using mounting option “N“, two mounting holes are req

14、uired on the card holders. The mounting options available for this CID specification sheet are as follows: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UNC 2B holes), or “G“ (tapped M2.5 x.45 metric holes). See figure 1 and table I for mountin

15、g hole spacing requirements. Card holders using mounting option “J“ may be shipped unassembled. Counterbore holes (for rivet mounting). The holes used for rivet mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 degrees by .140 inch (3.56 mm) diameter through holes with an acc

16、ess/clearance counterbore of .156 inch (3.96 mm) diameter by .200 inch (5.08 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59590 and the lengths avai

17、lable for this CID specification sheet are listed in table I. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE I. Assembly dimensions (see figure 1). 1/ PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “B“ .03 (0.8 mm) Dimension “M“ .005 (0.13 mm)

18、28 2.8 (71 mm) 2.30 (58.4 mm) .90 (22.9 mm) 38 3.8 (97 mm) 3.30 (83.8 mm) 1.90 (48.3 mm) 48 4.8 (122 mm) 4.30 (109.2 mm) 2.90 (73.7 mm) 58 5.8 (147 mm) 5.30 (134.6 mm) 3.90 (99.1 mm) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for general information only. Configuration. The

19、configuration of a card holder shall be as specified in table II. The details of a particular configuration consist of those on figure 1 and may include those on figures 2 and 3. The correct PIN configuration identifier for each option is listed in table II. Card holders not requiring the options de

20、scribed by table II shall leave the configuration position in the PIN blank. TABLE II. Configuration. Configuration Applicable figures Hardware added to basic configuration 1 No changes from basic configuration W 1 and 2 Lockwasher and flat washer E 1 and 3 Screw self-locking element D 1, 2, and 3 L

21、ockwasher, flat washer, and screw self-locking element Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/17B 4 Lockwasher and flat washer (see figure 2). The use of a lockwasher and flat washer located under the screw head will provide for addi

22、tional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwasher and flat washer shall include a suffix “W“ in the PIN (see classification and notes). FIGURE 2. Lockwasher and flat washer details. Screw self-locking element (see figure 3). The

23、use of a screw self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a screw self-locking element shall include a suffix “E“ in the PIN (see classification and notes). FIGU

24、RE 3. Screw self-locking element details. Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classification and notes). NOTES. PIN. The PIN should be used for Gove

25、rnment purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, General Requirements For. (Copies of t

26、hese documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Provided by IHSNot for ResaleNo reproduction or networking permitted without li

27、cense from IHS-,-,-AA59590/17B 5 Ordering data. Ordering data shall be as specified in AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specificat

28、ion sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the man

29、ufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 Card Lo

30、cks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in t

31、able III are only for length designator “28“. See table IV for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession da

32、ta. PIN designator AA59590/17 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28 A2452.80H 3245BA2.80H BN28 A2452.80 3245BA2.80 BT28 A2452.80T0 3245BA2.80T0 BV28 A2452.80T2 3245BA2.80T2 BG28 MA2452.80TM2.5 3245MBA2.80TM2.5 BJ28W WA2452.80H 3245WBA2.80H BN28W WA2452.80 324

33、5WBA2.80 BT28W WA2452.80T0 3245WBA2.80T0 BV28W WA2452.80T2 3245WBA2.80T2 BG28W MWA2452.80TM2.5 3245MWBA2.80TM2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/17B 6 TABLE III. Commercial part number supersessi

34、on data Continued. PIN designator AA59590/17 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28E A2452.80HL 3245BA2.80HL BN28E A2452.80L 3245BA2.80L BT28E A2452.80T0L 3245BA2.80T0L BV28E A2452.80T2L 3245BA2.80T2L BG28E MA2452.80TM2.5L 3245MBA2.80TM2.5L BJ28D WA2452.80HL 3

35、245WBA2.80HL BN28D WA2452.80L 3245WBA2.80L BT28D WA2452.80T0L 3245WBA2.80T0L BV28D WA2452.80T2L 3245WBA2.80T2L BG28D MWA2452.80TM2.5L 3245MWBA2.80TM2.5L CJ28 2452.80H 3245CG2.80H CN28 2452.80 3245CG2.80 CT28 2452.80T0 3245CG2.80T0 CV28 2452.80T2 3245CG2.80T2 CG28 M2452.80TM2.5 3245MCG2.80TM2.5 CJ28W

36、 W2452.80H 3245WCG2.80H CN28W W2452.80 3245WCG2.80 CT28W W2452.80T0 3245WCG2.80T0 CV28W W2452.80T2 3245WCG2.80T2 CG28W MW2452.80TM2.5 3245MWCG2.80TM2.5 CJ28E 2452.80HL 3245CG2.80HL CN28E 2452.80L 3245CG2.80L CT28E 2452.80T0L 3245CG2.80T0L CV28E 2452.80T2L 3245CG2.80T2L CG28E M2452.80TM2.5L 3245MCG2.

37、80TM2.5L CJ28D W2452.80HL 3245WCG2.80HL CN28D W2452.80L 3245WCG2.80L CT28D W2452.80T0L 3245WCG2.80T0L CV28D W2452.80T2L 3245WCG2.80T2L CG28D MW2452.80TM2.5L 3245MWCG2.80TM2.5L See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

38、,-,-AA59590/17B 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/17 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 EJ28 EN2452.80H 3245EN2.80H EN28 EN2452.80 3245EN2.80 ET28 EN2452.80T0 3245EN2.80T0 EV28 EN2452.80T2 3245EN2.80T2 EG28

39、MEN2452.80TM2.5L 3245MEN2.80TM2.5 EJ28W WEN2452.80H 3245WEN2.80H EN28W WEN2452.80 3245WEN2.80 ET28W WEN2452.80T0 3245WEN2.80T0 EV28W WEN2452.80T2 3245WEN2.80T2 EG28W MWEN2452.80TM2.5 3245MWEN2.80TM2.5 EJ28E EN2452.80HL 3245EN2.80HL EN28E EN2452.80L 3245EN2.80L ET28E EN2452.80T0L 3245EN2.80T0L EV28E

40、EN2452.80T2L 3245EN2.80T2L EG28E MEN2452.80TM2.5L 3245MEN2.80TM2.5L EJ28D WEN2452.80HL 3245WEN2.80HL EN28D WEN2452.80L 3245WEN2.80L ET28D WEN2452.80T0L 3245WEN2.80T0L EV28D WEN2452.80T2L 3245WEN2.80T2L EG28D MWEN2452.80TM2.5L 3245MWEN2.80TM2.5L HJ28 HA2452.80H 3245BH2.80H HN28 HA2452.80 3245BH2.80 H

41、T28 HA2452.80T0 3245BH2.80T0 HV28 HA2452.80T2 3245BH2.80T2 HG28 MHA2452.80TM2.5L 3245MBH2.80TM2.5 HJ28W WHA2452.80H 3245WBH2.80H HN28W WHA2452.80 3245WBH2.80 HT28W WHA2452.80T0 3245WBH2.80T0 HV28W WHA2452.80T2 3245WBH2.80T2 HG28W MWHA2452.80TM2.5L 3245MWBH2.80TM2.5 See footnotes at end of table. Pro

42、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/17B 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59590/17 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 HJ28E HA2452.80HL 3245BH2.80

43、HL HN28E HA2452.80L 3245BH2.80L HT28E HA2452.80T0L 3245BH2.80T0L HV28E HA2452.80T2L 3245BH2.80T2L HG28E MHA2452.80TM2.5L 3245MBH2.80TM2.5L HJ28D WHA2452.80HL 3245WBH2.80HL HN28D WHA2452.80L 3245WBH2.80L HT28D WHA2452.80T0L 3245WBH2.80T0L HV28D WHA2452.80T2L 3245WBH2.80T2L HG28D MWHA2452.80TM2.5L 324

44、5MWBH2.80TM2.5L RJ28 R2452.80HL 3245CC2.80HL RN28 R2452.80L 3245CC2.80L RT28 R2452.80T0L 3245CC2.80T0L RV28 R2452.80T2L 3245CC2.80T2L RG28 MR2452.80TM2.5L 3245MCC2.80TM2.5L RJ28W WR2452.80H 3245WCC2.80H RN28W WR2452.80 3245WCC2.80 RT28W WR2452.80T0 3245WCC2.80T0 RV28W WR2452.80T2 3245WCC2.80T2 RG28W

45、 MWR2452.80TM2.5 3245MWCC2.80TM2.5 RJ28E WR2452.80H 3245CC2.80HL RN28E WR2452.80 3245CC2.80L RT28E WR2452.80T0 3245CC2.80T0L RV28E WR2452.80T2 3245CC2.80T2L RG28E MWR2452.80TM2.5 3245MCC2.80TM2.5L RJ28D WR2452.80HL 3245WCC2.80HL RN28D WR2452.80L 3245WCC2.80L RT28D WR2452.80T0L 3245WCC2.80T0L RV28D W

46、R2452.80T2L 3245WCC2.80T2L RG28D MWR2452.80TM2.5L 3245MWCC2.80TM2.5L See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/17B 9 TABLE III. Commercial part number supersession data Continued. 1/ The CID PINs listed ar

47、e only for length designator “28“”. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59590. TABLE IV. Example of PIN with available length designators. PIN designator AA59590/17 Vendor similar designator or type part number 1/ 2/ CAGE 61081