DLA A-A-59494 7 A-2013 HUB ASSEMBLY CANTILEVER MOUNTING FOR 6 00-9 7 50-10 AND 9 00-10.pdf

《DLA A-A-59494 7 A-2013 HUB ASSEMBLY CANTILEVER MOUNTING FOR 6 00-9 7 50-10 AND 9 00-10.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59494 7 A-2013 HUB ASSEMBLY CANTILEVER MOUNTING FOR 6 00-9 7 50-10 AND 9 00-10.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND A-A-59494/7A 27 February 2013 SUPERSEDING A-A-59494/7 28 April 2010 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HUB ASSEMBLY, CANTILEVER MOUNTING, FOR 6.00-9, 7.50-10, AND 9.00-10 The General Services Administration has authorized the use of this commercial item description for all fe

2、deral agencies. The complete requirements for procuring hubs described herein shall consist of this document and the issue in effect of A-A-59494. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is incl

3、uded in the PIN as shown in the following example (see NOTES). AA59494 /07 - 001 CID number Applicable CID specification sheet (two digits) Dash number (see figure 1) SALIENT CHARACTERISTICS. Interface and physical dimensions. Hubs supplied to this CID specification sheet shall be as specified herei

4、n (see figure 1). AMSC N/A FSC 2530 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59494/7A 2 FIGURE 1. Hub assembly, cantilever mounting, for 6.00-9, 7.50-10, and 9.00-10 wheels. Provided by IHSNot for ResaleNo reproduction or networking permit

5、ted without license from IHS-,-,-A-A-59494/7A 3 Dash number Material 001 Steel 002 Aluminum alloy 003 Cast iron Inches mm Inches mm Inches mm 0.031 0.8 0.75 19.1 2.094 53.2 0.1196 3.0 0.844 21.4 2.125 54.0 0.125 3.2 0.875 22.2 2.4405 62.0 0.141 3.6 1.0 25.4 2.656 67.5 0.156 4.0 1.005 25.5 2.995 76.1

6、 0.165 4.2 1.188 30.2 3.062 77.8 0.188 4.8 1.156 29.4 3.063 77.8 0.25 6.4 1.2495 31.7 3.99 101.3 0.281 7.1 1.362 34.6 4.375 111.1 0.375 9.5 1.6245 41.3 4.5 114.3 0.625 15.9 1.688 42.9 5.5 139.7 6.75 171.5 FIGURE 1. Hub assembly, cantilever mounting, for 6.00-9, 7.50-10, and 9.00-10 wheels Continued.

7、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59494/7A 4 NOTES: 1. Timken Company roller PIN denoted, or equal. 2. Dimension shown is for steel or cast iron hub. For aluminum, use 2.9985, +0.0000, -0.0010. 3. Dimension shown is for steel or ca

8、st iron hub. For aluminum, use 2.4395, +0.0000, -0.0010. 4. Nut, castellated, steel, thread 1.0000-14UNF-3B, zinc plated. 5. Cotterpin, 0.1250 (nominal).diameter. 6. Hub shall fit wheels specified in A-A-59494/4 and A-A-59494/5. 7. Dimensions are in inches. 8. Metric equivalents are given for inform

9、ation only. 9. Material: steel, cast iron, or aluminum alloy. FIGURE 1. Hub assembly, cantilever mounting, for 6.00-9, 7.50-10, and 9.00-10 wheels Continued. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification

10、section for PIN format example. Source of documents. Commercial Item Descriptions A-A-59494 - Wheels and Hubs for Industrial Pneumatic Tires A-A-59494/4 - Wheel, Pneumatic Tire, 6.00-9 A-A-59494/5 - Wheel, Pneumatic Tire, 7.50-10 or 9.00-10 (Copies of these documents are available online at https:/a

11、ssist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commerc

12、ial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be u

13、sed to restrict procurement to only the manufacturers shown.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59494/7A 5 MFRs CAGE MFRs name and address 52793 Saginaw Products Corporation 68 Williamson St. Saginaw, MI 48601-3246 Phone: 989-753-14

14、11 Fax: 989-753-4386 http:/ 56190 Metadure Parts & Sales Inc. 165 Gazza Blvd. Farmingdale, NY 11735 Phone: 631-249-2141 Fax: 631-249-4546 0W357 PDI Ground Support Systems Inc. 5905 Grant Ave. Cleveland, OH 44515-5609 Phone: 216-271-7344 Fax: 216-271-7550 davidrpdi- http:/www.pdi- Part number (P/N)

15、 supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown (see table I). This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE I. P/N supersession data. Dash number (see figure 1) A-A-59494/7 MFRs CAGE

16、 MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ MFRs CAGE MFRs P/N 1/ 001 52793 N/A 56190 N/A 0W357 N/A 002 52793 6403-AL 56190 N/A 0W357 N/A 003 52793 6403-M 56190 N/A 0W357 N/A 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of prepara

17、tion of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph of A-A-59494. National stock number (NSN). The following is a list of NSNs assigned which correspond

18、to this CID specification sheet. The list is for information only and may not be indicative of all possible NSNs associated with the CID specification sheet. For up to date information on assigned NSNs, please contact the aforementioned DSCC office listed in A-A-59494 (see table II). Provided by IHS

19、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59494/7A 6 TABLE II. NSNs. Dash number (see figure1) A-A-59494/7 NSN 001 2530-00-893-0568 002 2530-00-646-7705 003 N/A Changes from previous issue. Marginal notations are not used in this revision to identify chan

20、ges with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY AND COORDINATING ACTIVITY: Custodians: GSA - FAS Army - AT Air Force - 99 Preparing activity: DLA CC DLA - CC Review activity: Project 2530-2013-001 Air Force - 84 NOTE: The activities li

21、sted above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-