DLA A-A-55563 13 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf

《DLA A-A-55563 13 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55563 13 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA55563/13B 22 June 2012 Superseding AA55563/13A 31 January 2002 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES, WITH CONTROLLED INSIDE BEND RADIUS The General Servic

2、es Administration has authorized the use of this commercial item description (CID) for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. CLASSIFICATION /IDENTIFICATION NUMBE

3、R (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see NOTES). AA55563 CID number /13 Applicable CID sheet * Material (See table I) * Card holder width/board thi

4、ckness * * Length (See table II) * Finish (See table III) Example: AA55563/13AC20D is the PIN for a beryllium copper 1/4 hard, 2.0 inches (51 mm) long, ebonal finished, low profile, open ended, flared entry, card holder having 2 two offset (side) mounting holes. The card guide is designed to accommo

5、date circuit card assemblies with printed board thicknesses of .0937 inch (2.29 mm). SALIENT CHARACTERISTICS. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figure 1, table I, and table II) and meet the general requireme

6、nts specified in CID AA55563. Material type. Material types shall be defined in of AA55563. The applicable material type designators for this CID specification sheet are “A“ (beryllium copper H, temper TD01), “B“ (beryllium copper HT, temper TH01), or “D“ (stainless steel H). Material thickness. The

7、 material thickness shall be .005 .002 inch (0.13 0.05 mm). Card holder width/board thickness. The card holder width/board thickness shall be defined in table I herein and as shown in figure 1 as dimensions “D“ and “T“. The applicable card holder width/board thickness designators for this CID specif

8、ication sheet are A, B, or C, and shall be included in the PIN. Overall length. Overall length is shown on figure 1 as dimension “L“, and is displayed in table II herein. Applicable overall length designator 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, or 75 shall be included in the PIN. AMSC N/A FSC

9、 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/13B 2 Finish. Finish materials types shall be defined in AA55563. Applicable finish materials designators “C“ (copper plate), “D“ (black ebonal), “E“ (gold plate), “F“ (nickel plate), “H“

10、(silver plate), “J“ (zinc, yellow chromate), “K“ (no finish), or “R“ (zinc, clear chromate) are available for material type designators “A“ and “B“. Finish designator “G“ (passivate) is the only finish available for material type designator “D“ (stainless steel). The finish designator shall be inclu

11、ded in the PIN. Mounting hole spacing. Mounting hole spacing is shown on figure 1 as dimension “M“. Dimension “M“ is listed in table II herein. Inches mm Inches mm Inches mm Inches mm Inches mm .001 .003 .005 0.03 0.08 0.13 .010 .015 .020 0.25 0.38 0.51 .067 .070 .078 1.72 1.78 1.92 .100 .120 .125 2

12、.54 3.05 3.18 .148 .250 .37 3.76 6.35 9.39 NOTES: 1. Dimensions are in inches. 2. Millimeter equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .02 inch (0.51 mm), for 2 places and .010 inch (0.25 mm), for 3 places. FIGURE 1. Card holder design and dime

13、nsions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/13B 3 TABLE I. Card holder width/board thickness. PIN designator for card holder width / board thickness Fractional equivalent Card holder width 1/ 2/ Dimension “D“ max Board thickness 1

14、/ 2/ 3/ Dimension “T“ ref Inches mm Inches mm A 1/32 .27 6.85 .0312 0.76 B 1/16 .27 6.85 .0625 1.52 C 3/32 .27 6.85 .0937 2.29 1/ See dimensions “D“ and “T“ in view A A on in figure 1. 2/ Do not use card holder width/board thickness, dimensions “D“ or “T“ for PIN construction. 3/ Dimension “T“ is gi

15、ven as reference. TABLE II. Length and hole spacing. 1/ PIN designator for overall length Dimension “L“ .020 (0.51) Dimension “M“ .005 (0.13) Inches mm Inches mm 20 2.0 51 1.75 44.5 25 2.5 54 2.25 57.2 30 3.0 76 2.75 69.9 35 3.5 89 3.25 82.6 40 4.0 102 3.75 95.3 45 4.5 114 4.25 108.0 50 5.0 127 4.75

16、 120.7 55 5.5 140 5.25 133.4 60 6.0 152 5.75 146.1 65 6.5 165 6.25 158.8 70 7.0 178 6.75 171.5 75 7.5 191 7.25 184.2 1/ Millimeters are given for general information only. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the c

17、lassification section for PIN format example. Source of documents. Commercial Item Description AA55563 Holder, Electrical Card, Metal Card Guide, General Requirements (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardiza

18、tion Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in AA55563. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/13B 4 Commercial products. As part of the m

19、arket analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements o

20、f this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pent

21、air Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 URL: Part number (P/N) supersession data. These CID specification sheet PINs supersede the following manufacturers P/Ns in table III as shown. The CID PINs lis

22、ted in table III cover the different lengths available. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. CID PIN; AA55563/13#$ AA55563/13#$& 1/ Manufacturers 2/ Material type () Card holder

23、 width/board thickness Overall length ($) Finish (&) CAGE 18915 4/ B # 60 3/ 35F7BHT12P B # 65 3/ 35F7BHT13P B # 70 3/ 35F7BHT14P B # 75 3/ 35F7BHT15P D # 20 G 35F7CRT4 D # 25 G 35F7CRT5 D # 30 G 35F7CRT6 D # 35 G 35F7CRT7 D # 40 G 35F7CRT8 D # 45 G 35F7CRT9 D # 50 G 35F7CRT10 D # 55 G 35F7CRT11 D #

24、 60 G 35F7CRT12 D # 65 G 35F7CRT13 D # 70 G 35F7CRT14 D # 75 G 35F7CRT15 1/ See CLASSIFICATION OR /IDENTIFICATION NUMBER (PIN) herein for symbol representations. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of pre

25、paration of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “H“, “K“, “C“, “D“, “E“, “F“, “R“, or “J“ are available for this material

26、 type. 4/ Manufacturer CAGE 18915 superseded part number the series type is “35F7“, the letters “B“, “BH“, or “CR“ denotes material type, the letter “T“ denotes card holder width/board thickness (see table I), the numbers “2“ through “15“ denotes card holder lengths, and the letter “P“ denotes finis

27、h material. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Navy EC Air Force 99 Preparing activity: DLA CC DLA CC Project 59982012030 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-