DLA A-A-55563 12 C-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITHOUT FLARED ENTRY WITH 3 OFFSET (SIDE) MOUNTING HOLES.pdf

《DLA A-A-55563 12 C-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITHOUT FLARED ENTRY WITH 3 OFFSET (SIDE) MOUNTING HOLES.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55563 12 C-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITHOUT FLARED ENTRY WITH 3 OFFSET (SIDE) MOUNTING HOLES.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA55563/12C 22 March 2012 Superseding AA55563/12B 14 May 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 3 OFFSET (SIDE) MOUNTING HOLES The General Services Administration has authorized the

2、 use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item descr

3、iption (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA55563 CID number /12 Applicable CID specification sheet Material # Card holder width/ board thickness (see table I) XX Overa

4、ll length (see table II) AA55563/12#XX AA55563/12#XX& 1/ Manufacturers 2/ Material type Card holder width/board thickness Overall length designator (XX) Finish 3/ CAGE 18915 4/ # 10 & 35C7BHT2F B # 15 & 35C7BHT8F B # 20 & 35C7BHT8F B # 25 & 35C7BHT8F B # 30 & 35C7BHT8F B # 35 & 35C7BHT8F B # 40 & 35

5、C7BHT8F B # 45 & 35C7BHT9F B # 50 & 35C7BHT10F B # 55 & 35C7BHT11F B # 60 & 35C7BHT12F B # 65 & 35C7BHT13F B # 70 & 35C7BHT14F B # 75 & 35C7BHT15F D # 10 G 35C7CRT2 D # 15 G 35C7CRT3 D # 20 G 35C7CRT4 D # 25 G 35C7CRT5 D # 30 G 35C7CRT6 D # 35 G 35C7CRT7 D # 40 G 35C7CRT8 D # 45 G 35C7CRT9 D # 50 G

6、35C7CRT10 D # 55 G 35C7CRT11 D # 60 G 35C7CRT12 D # 65 G 35C7CRT13 D # 70 G 35C7CRT14 D # 75 G 35C7CRT15 See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/12C 6 TABLE III. Commercial part number supersession data Cont

7、inued. 1/ See Classification/Part or Identification Number paragraph for symbol representations. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial products were

8、 reviewed and could be replaced by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “H“, “K“, “C“, “D“, “E“, “F“, “R“, or “J“ are available for this material type. 4/ MFG CAGE 18915 the series type is “35C7“, (with center

9、mounting hole and without flare) the letters “B“, “BH“, or “CR“ denotes material type, the letter “T“ denotes card holder width/board thickness (see table I), the numbers “2“ through “15“ denotes card holder lengths, and the letter “F“ denotes finish material. Guidance on use of alternative parts wi

10、th less hazardous or nonhazardous materials. This CID specification sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function requirements of their application. MILITARY INTERESTS: CI

11、VIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Preparing Activity Air Force 85 DLA CC DLA CC Review activities: Project: 59982011031 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-