DLA A-A-55203-1993 SUSPENDERS TROUSERS (FLYING SUIT)《长裤(飞行员西装)吊裤带》.pdf

《DLA A-A-55203-1993 SUSPENDERS TROUSERS (FLYING SUIT)《长裤(飞行员西装)吊裤带》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55203-1993 SUSPENDERS TROUSERS (FLYING SUIT)《长裤(飞行员西装)吊裤带》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55203 9999974 0144310 820 = b INCH-POUND I i ? A-A-552 03 03 MAY 1993 COMMERCIAL ITEM DESCRIPTION SUSPENDERS, TROUSERS (FLYING SUIT) The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-S-6790. Abstract. This commercial item descript

2、ion covers suspenders for use with flying clothing. Classification. The Suspenders, Trousers shall be in the following 0 types: Type I - Elastic Type II - Nonelastic Salient Characteristics. The suspenders shall consist of two strips of webbing, 1-1/2 inch wide for Type I - Elastic and Type II - Non

3、elastic and shall be colored sage green shade No. 1514, DPSC HANDBOOK 4120.1. The suspenders will have a crisscross pattern with wire buttonholes on two of the ends and leather buttonholes on the other two ends as shown in figure 1. Beneficial comments (recommendations, additions, deletions) and any

4、 pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426)

5、appearing at the end of this document or by letter. AMSC N/A FSC 8440 a DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Material. The Type I elastic webbing shall be a

6、cotton, and rubber, woven construction measuring 1-1/2 inch wide 5 1/16 and cut to 34-inch long strips. The Type II nonelastic webbing shall be a one hundred percent cotton woven fabric measuring 1-1/2 inch wide a ferrule and a suspender hook made from 0.015-inch 1010 hot rolled steel, and a complet

7、e snap fastener set. Label/markinq. Each suspenders shall be permanently and legibly indented or marked with the manufacturers name or trademark of such characters as to be identifiable with the manufacturer. WorkmanshiD. After completion, the finished suspenders shall be thoroughly cleaned, and all

8、 loose thread, lint, sharp edges, and foreign matter removed. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evalu

9、ated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresp

10、onding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Reaulatorv Reauirements. The offeror/contracto

11、r is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality Assurance Certification. The contractor shall certify that the product offered . meets the salient characteristics and the requirements of this commercial item description, and

12、where certificates of compliance are conformance prior or to check such items to determine the validity of submitted, the government reserves the right eo require proof of such t the certificate. Examination. Lots of suspenders shall be inspected in accordance with Itsampling Procedures and Tables f

13、or Inspection by Attributesvt, ANSI/ASQC 21.4, published by the American Society for Quality Control. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-v Visual Examination. The suspenders shall be examined for the defects listed below. The lot size

14、shall be expressed in units of suspenders. The sample unit is one suspender. the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 2.5. The inspection level shall be II and Packaqinq Examination. The fully packaged shipping containers shall be examined in acco

15、rdance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 2.5. Dimensional Examination. The finished suspenders shall conform to the dimensions

16、specified. tolerance shall be classified as a defect. The sample unit shall be one; the inspection level shall be 5-3 and the AQL shall be 4.5. Packaqina Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of

17、 shipping containers in the inspection lot. The inspection level shall be S-2 and AQL shall be 2.5. Any dimension that is not within the established Examination Defect Mater ia1 Missing, damaged, not as required. Marking (exterior Omitted, incorrect, illegible, of and interior) improper size, locati

18、on, sequence or method of application. Content Workmanship Palletization Number of suspenders per shipping container is more or less than required. flaps, loose or inadequate strapping. Incomplete closure of container Length, width, or height exceeds specified maximum requirements Pallet type not as

19、 specified Load not bonded as specified 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55203 m 9999974 0144313 53T m A-A-5 52 03 Defects. any hole, cut, tear, color not as specified; any spot or stain (outside); thread ends not removed; label

20、missing, incorrect, or illegible; brand marks and excessive softness of leather; broken or malformed, corroded areas, burr or sharp edges; measurement of item not as specified. Preservation, Packins, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order.

21、The suspenders shall be examined for the following defects: Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonsovernment Documents. ANSI/ASQC 21.4 - S

22、ampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018-3308.) Custodian: Army - AV Navy - AS Air Force - 99 Review Activity: Air Force - 82 Civil Agency Coordinating Activity

23、: GSA - FSS Preparing Activity: DLA - CT User Activity: Project No.8440-0204 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L A-A-55203 9999974 Ol44314 47b A-A-52203 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-