DLA A-A-55182-1993 COVER PERSONNEL IDENTIFICATION TAG《个人身份标签床罩（封面）》.pdf

《DLA A-A-55182-1993 COVER PERSONNEL IDENTIFICATION TAG《个人身份标签床罩（封面）》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55182-1993 COVER PERSONNEL IDENTIFICATION TAG《个人身份标签床罩（封面）》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55182 = 74 O1447b2 852 A-A-55182 26 April 1993 c COMMERCIAL ITEM DESCRIPTION COVER, PERSONNEL IDENTIFICATION TAG The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-C-14635. Abstract. This commercial item description covers one type

2、 and size of plasticized polyvinyl chloride cover sized to fit over the standard personnel identification tag. The finished cover shall be capable of being irreversibly marked with a standard government ball point pen using heavy pressure. Sal i ent Characteri sti cs. Tne Tag covers dimensions shall

3、 be 2-5/16 x 1-11/32 x 1/32 inches thick (see Figures 1 ;:ET:; EL :!-.E e:. G: LL ri,. s I Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, b b 0 i document or by letter. iMSC NA FSC 8465 DISTRIBUTION STATEMENT A. Approved for pub1 i c re1 ease; Di stri bution is un1 imi ted. Licensed

4、by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55 182 Material. The plasticized polyvinyl chloride composition shall be non-toxi c and non-al 1 ergeni c. The materi al (after curi ng) shai 1 be soft flexible elast

5、omerjc pi asti c. Workmanship. After completion, the finished tag cover, shall be thoroughly cleaned and all excess material removed in the final processing. The finished tag should have no objectionable odor; edges should be smooth; n3 lettering missing or not completely molded; no holes missing; s

6、urface should not contain voids or pockets. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed ar,d evaluated by the gover

7、nment. Evaluation criteria an basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstrtion Model approved by DPSC under the resultant contract will serve as a manufocturing standard for the corresponding production i

8、tems delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Quality Assurance Certification. The contractor shall certify tha

9、t the product offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specifications, standarcts and quality assurance practices. The government reserves the right to reqire proof of sucn conformance prior to the first delivery and t

10、hereafter as may be otherwise provided for, under the provisions of the contract. Reljance on contractor PA systems shall not relieve the contractor of the responsibility of ensuring that ali products or supplies subBitte0 to the government for acceptance comply with all requirements of the contract

11、. Component Testing. The plasticized polyvinyl chloride shall be tested for the characteristics listed in table ii. The inspection level shail be I and the acceptable quality leve? (AQL), expressed in terms of defects per hundred units, shall be 1.2. The lot size for the plsticized polyvinyl chlorid

12、e shall be expressed in units of 1 pound. The sample unit shall be fcijr pieces and each piece shall be i8 inches by 6 inches by 0.025 inch. I . 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55182 = 9999974 0344764 625 A-A-55182 TABLE I: Comp

13、onent Testing Extefit of burning tzst ASTM D 568 See 1) Tensile strength at break 2300 p.s.i. ASTM D 412 Ultimate elongation, percent 335 ASTM D 412 Tensile stress t 100 percent elongation 725 p.s.i. ASTM D 412 Tear resistance iposnds per inch of thickness) 225 ASTM D 624 See 2) i) The results shall

14、 be reported as pass (self-extinguishing) or fail. 2) Die C specimens shall be used. End Item Performance Testina. The end items shall conform to the indicated marking requirements when tested. The lot size shall be expressed in units of covers. The sample unit shall be one cover. The inspection lev

15、el shal? be S-1. Any test failure shall be cause for ejection of the lot. Regulatory Requirements. The offerorlcontractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Preservation, Packaging, Labeling, Packing and Marking. The prese

16、rvati on, packagi ng, t abel i ng packi ng, and rnarki ng shall be as specified in the contract or order. Source of Government Document. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bidg. 4D 700 Robbins Avenue Philadelphia, Pa. 19111-5094 3 Provid

17、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55182 Sources of Nonaovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables for inspection By Attri butes I l (Appl i cati ons for Copi es should be addressed to Ameri can Nati onal Standard

18、s Institutes, 1430 Broadway, New York, NY iUC18-3308) ASTM-D 3951 - Standard Practice for Commercial Packaging (Applications for copies shouid be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, Pa. i9103) Custodian: Army - GL Navy - NU Air Force - 99 Review A

19、ctivity: Army - MD Navy - MC Air Force - 82 Air Force - 45 User Activity: Army - SM Navy - MS Air Force - 45 Ci vi 1 Agency Coordi nati ng Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0112 I 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

20、rom IHS-,-,-A-A-55282 m 9999974 OL447bb 4TB 1 - -* - 28TSS-V-V Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55182 = 9999974 0344767 33q A-A-55182 A I J I 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-