DLA A-A-50013 G-2009 UNDERSHIRT QUARTER-SLEEVE.pdf

《DLA A-A-50013 G-2009 UNDERSHIRT QUARTER-SLEEVE.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-50013 G-2009 UNDERSHIRT QUARTER-SLEEVE.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 A-A-50013G September 15, 2009 SUPERSEDING A-A-50013F June 22, 2009 COMMERCIAL ITEM DESCRIPTION UNDERSHIRT, QUARTER-SLEEVE The General Services Administration has authorized the use of this commercial item description for all Federal agencies. 1. SCOPE. This commercial item description covers the re

2、quirements for a cotton, quarter- sleeve undershirt worn by military personnel of the Department of Defense. 2. CLASSIFICATION. The undershirt shall be of the following types, classes, and sizes as specified (see 7.5): 2.1 Types. Type I: Crew neck, cotton Type II: “V” neck, cotton 2.2 Classes. Class

3、 1 - White Class 5 - Navy Blue 3388 Class 2 - Foliage Green 504 Class 6 - Brown 436 Class 3 - Blue 3362 Class 7 - Olive Green 109 Class 4 - Black 357 Class 8 - Air Force Sand 1643 AMSC N/A FSC 8420 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited Comments, suggestions

4、, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP Standardization Team, 700 Robbins Avenue, Philadelphia, PA 19111-5096. Since contact information can change, you may want to verify the currency of the address in

5、formation using Acquisition Streamlining and Standardization Information System (ASSIST) online database http:/assist.daps.dla.mil/. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50013G 2 2.3 Sizes. The undershirts shall be of one of

6、 the following sizes: XX-Small, X-Small, Small, Medium, Large, X-Large, XX-Large, XXX-Large 3. SALIENT CHARACTERISTICS. 3.1 Description. The undershirts shall have hemmed quarter-length sleeves, a crew neck (Type I) or “V” neck (Type II) collarette, and a hemmed bottom (see Figures 1 and 2). The col

7、larette shall be made of a double thickness of basic material to finish 7/8(+/- 1/8) inch wide. The inside of the shoulder and back of collarette seam (shoulder to shoulder) shall be reinforced with 3/8to inch wide tape of basic knit fabric. The length of the neck binding shall be cut along the grai

8、n. 3.2 Materials. 3.2.1 Basic material. The body cloth shall be made of single or 2-ply 100 percent combed cotton yarn, knitted on a circular machine with a jersey stitch. No materials having a tendency to cause latent tendering or yellowing of the cloth shall be used in any of the dyeing or finishi

9、ng operations. Resin finishes shall not be used. The cloth shall be preshrunk and shall conform to the requirements specified in Table I. 3.2.1.1 Collarette material. The collarette cloth shall be made of 100 percent combed cotton yarn and shall be a 1x1 rib knit cloth. No materials having a tendenc

10、y to cause latent tendering or yellowing of the cloth shall be used in any of the dyeing or finishing operations. Resin finishes shall not be used. The cloth shall be preshrunk and shall conform to the requirements specified in Table I. 3.2.2 Color. The Type I undershirt and collarette fabric shall

11、match the standard fabrics for Class 2, Class 3, Class 4, Class 5, Class 6, Class 7, and Class 8. The Class 1 undershirt and collarette fabric shall be bleached white. For the Type II undershirt and collarette fabric, the cloth shall be bleached white. 3.2.2.1 Visual shade matching. The color and ap

12、pearance of the undershirts shall match the standard sample when viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature 7500 +/- 200oK, with illumination of 100 +/- 20 foot candles, and shall be a good match to the sta

13、ndard sample under incandescent lamplight at 2856 +/- 200oK. TABLE I. Material requirements Basic Material Characteristic Requirement Test Method Fabric Weight (oz/sq yd.) 4.5 (+/- 0.2) ASTM-D-3776, Opt. C Fabric Count Wales per inch Courses per inch 30 (+/- 1.0) 36 (+/- 1.0) ASTM-D-3887 ASTM-D-3887

14、 Bursting strength (pounds) 60 ASTM-D-3787 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50013G 3 TABLE I. Material requirements (continued) Basic Material Characteristic Requirement Test Method Colorfastness to: (min.) Laundering (3 cycles) Cr

15、ocking Perspiration (acid any spot or stain on outside, discoloration or color not as specified, any shaded part, any objectionable odor Seams and stitching Loose or tight stitching tension, broken or missing thread or stitch, needle chew; any part caught in an unrelated operation or stitching; raw

16、edge, thread breaks, thread ends not removed; any seam puckered, pulled, distorted, pleated, irregular or open; pulled or snagged stitches, twisted seams Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50013G 7 TABLE III. Visual examination defec

17、ts (continued) Workmanship Any component part omitted, twisted, not specified size, missing, misplaced, or poorly shaped; any dimension of item not as specified; neck stretched or loose; design not as specified. Labels Label(s) missing, incorrect, or illegible; bar code or UPC code label omitted or

18、not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code label causes damage to the item. Packaging Not packaged in accordance with the contract or purchase order. 5.4 Acceptance Criteria. Acceptance criteria shall be

19、as specified in the contract or purchase order. 6. PACKAGING. 6.1 Preservation, packing and marking. Preservation, packing and marking shall be specified in the contract or order (see 7.5). 7. NOTES. 7.1 Sources of Government documents. 7.1.1 Copies of government documents are available online at ht

20、tp:/assist.daps.dla.mil/quicksearch/ or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. 7.1.2 Federal Acquisition Regulations are available online at http:/acquisition.gov/far/index.html or by contacting the Superintendent of Documents at

21、202-512-1800. 7.2 Sources of Non Government Documents. 7.2.1 AATCC Standards are available online at www.aatcc.org or from the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-2215. 7.2.2 ASTM Standards are available online at www.astm.org or f

22、rom ASTM International, 100 Barr Harbor Drive, P.O. Box C700 West Conshohocken, PA 19428-2959. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50013G 8 7.2.3 Principles and Methods of Toxicology (fourth edition), A. Wallace Hayes (editor), pp 105

23、7-1060, 2001 are available from Taylor and Francis, Philadelphia, PA or http:/www.taylorandfrancis.co.uk/. 7.3 Referenced Documents. A-A-52094 - Thread, Cotton A-A-50199 - Thread, Polyester Core, Cotton, or Polyester-Covered MIL-DTL-32075 - Label, for Clothing, Equipage, and Tentage (General Use) 7.

24、4 Miscellaneous. For access to information such as patterns, drawings, standard shade samples of cloth etc., go to Defense Supply Center Philadelphias website for their Specification/Pattern, Drawing request form at: http:/www.dscp.dla.mil/portal/sreqform.aspx. Complete request form and submit. 7.5

25、Ordering Data. The contract order shall specify the following: a. Commercial Item Description document number. b. Type, classes, and sizes required. c. Product conformance provisions. d. Packaging requirements. e. When toxicity testing is required. 7.6 Key Words. T-Shirt Provided by IHSNot for Resal

26、eNo reproduction or networking permitted without license from IHS-,-,-A-A-50013G 9 FIGURE 1. Type I Note: Dimension “A” is measured 2 inches below the armhole openings from folded edge to folded edge. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A

27、-A-50013G 10 FIGURE 2. Type II Note: Dimension “A” is measured 2 inches below the armhole openings from folded edge to folded edge. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50013G 11 MILITARY INTERESTS: Custodians: CIVIL AGENCY COORDINATIN

28、G ACTIVITY: Army GL GSA FSS Navy NU Air Force 11 PREPARING ACTIVITY: DLA CT Review Activities: Navy MC Project Number: 8420-2009-001 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, currency of the information above should be verified using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-