DIN V ENV 14062-1-2003 Identification card systems - Surface transport applications Electronic fee collection - Part 1 Physical characteristics electronic signals and transmission .pdf

《DIN V ENV 14062-1-2003 Identification card systems - Surface transport applications Electronic fee collection - Part 1 Physical characteristics electronic signals and transmission .pdf》由会员分享，可在线阅读，更多相关《DIN V ENV 14062-1-2003 Identification card systems - Surface transport applications Electronic fee collection - Part 1 Physical characteristics electronic signals and transmission .pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Februar 2003VornormIdentifikationskartensystemeLandgebundene VerkehrsanwendungenElektronischer GebhreneinzugTeil 1: Physikalische Eigenschaften, elektronische Signale undbertragungsprotokolle; Englische Fassung ENV 14062-1:2001VENV 14062-1ICS 35.240.15Identification card systems Surface transport ap

2、plications Electronicfee collection Part 1: Physical characteristics, electronic signals andtransmission protocols;English version ENV 14062-1:2001Systmes de cartes didentification Applications pour le transportterrestre Tlpage Partie 1: Caractristiques physiques, signauxlectroniques et protocoles d

3、e transmission;Version anglaise ENV 14062-1:2001Eine Vornorm ist das Ergebnis einer Normungsarbeit, das wegen bestimmter Vorbehalte zum Inhalt oderwegen des gegenber einer Norm abweichenden Aufstellungsverfahrens vom DIN noch nicht als Normherausgegeben wird.Zur vorliegenden Vornorm wurde kein Entwu

4、rf verffentlicht.Erfahrungen mit dieser Vornorm sind erbeten vorzugsweise als Datei per e-Mail an nidin.de in Form einer Tabelle. Die Vorlage dieser Tabelle kannim Internet unter http:/www.din.de/stellungnahme abgerufen werden; oder in Papierform an den Normenausschuss Informationstechnik (NI) im DI

5、N, Deutsches Institut frNormung e. V., Burggrafenstrae 6, 10787 BerlinNationales VorwortDie vorliegende Norm ist Teil einer mehrteiligen Norm mit dem Titel Identifikationskartensysteme Landgebundene Verkehrsanwendungen. Sie stammt aus dem Arbeitsprogramm von CEN/TC 224.Das Prsidium des DIN hat mit P

6、rsidialbeschluss 13/1983 festgelegt, dass Deutsche Normen, Vornormenund Norm-Entwrfe in Ausnahmefllen und unter bestimmten Bedingungen in Englisch verffentlichtwerden drfen. Diese Bedingungen sind fr diese Norm erfllt.Um den Gebrauch der Norm zu erleichtern, enthlt das nationale Vorwort Aussagen ber

7、 denAnwendungsbereich, ein Fachwrterverzeichnis sowie identische oder sachlich bereinstimmendeDeutsche Normen zu den in ENV 14062-1 zitierten Normen und andere Unterlagen.Fr die im Abschnitt 2 zitierten Internationalen Normen wird im Folgenden auf die entsprechendenDeutschen Normen hingewiesen:ISO/I

8、EC 7810:1995 siehe DIN EN ISO/IEC 7810ISO/IEC 7811-1:1995 siehe DIN EN ISO/IEC 7811-1ISO/IEC 7811-3:1995 siehe DIN EN ISO/IEC 7811-3ISO/IEC 7812-1:1993 siehe DIN EN ISO/IEC 7812-1Fortsetzung Seite 2 und10 Seiten ENVNormenausschuss Informationstechnik (NI) im DIN Deutsches Institut fr Normung e.V. DI

9、N Deutsches Institut fr Normung e.V. .Jede Art der Vervielfltigung, auch auszugsweise, Ref. Nr. DIN V ENV 14062-1:2003-02nur mit Genehmigung des DIN Deutsches Institut fr Normung e. V., Berlin, gestattet. Preisgr. 08 Vertr.-Nr. 0008Alleinverkauf der Normen durch Beuth Verlag GmbH, 10772 BerlinVornor

10、mB55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 DIN V ENV 14062-1:2003-022Nationaler Anhang NA(informativ)LiteraturhinweiseDIN EN ISO/IEC 7810, Identifikationskarten Physikalische Eigenschaften (ISO/IEC 7810:1995); DeutscheFassung EN ISO/IEC 7810:1996.DIN EN ISO/IEC 7811-1, Ide

11、ntifikationskarten Aufzeichnungstechnik Teil 1: Prgen von Schrift-zeichen (ISO/IEC 7811-1:1995); Deutsche Fassung EN ISO/IEC 7811-1:1996.DIN EN ISO/IEC 7811-3, Identifikationskarten Aufzeichnungstechnik Teil 3: Lage der geprgtenSchriftzeichen auf ID-1-Karten (ISO/IEC 7811-3:1995); Deutsche Fassung E

12、N ISO/IEC 7811-3:1996.DIN EN ISO/IEC 7812-1, Identifikationskarten Kennzeichnung eines Kartenausgebers Teil 1:Numerierungssystem (ISO/IEC 7812-1:1993); Deutsche Fassung EN ISO/IEC 7812-1:1995.AnwendungsbereichDiese Europische Vornorm legt physikalische Eigenschaften, elektronische Signale undbertrag

13、ungsprotokolle fr Chipkarten und in Bezug auf Anforderungen an die Bordeinheit (OBU) Anwendungen fr den elektronischen Gebhreneinzug in Verkehrsanwendungen, basierend auf DSRCoder GSM Technologie fest.Ziel ist die Interoperabilitt von Chipkarte und Bordeinheit, basierend auf DSRC oder GSM Technologi

14、e,unabhngig von Herstellern und bertragungstechnologien. Es werden sowohl Umwelt- als auchsystembezogene Aspekte mit Mindestanforderungen an die Konformitt bercksichtigt.Die festgelegten Anforderungen beziehen sich auf die Chipkarte (ICC) selbst, auf das im Fahrzeugbefindliche Kartenzugangsgert (OBU

15、) oder auf eine Kombination von beiden.Es werden keine Anforderungen an andere Kartenzugangsgerte auerhalb der Bordeinheit z. B. anstationren Gerten festgelegt.Englisch Deutsche Fachwrterliste fr ENV 14062-1Englisch DeutschEmbossing HochprgungInsertion-removal endurance Belastungsprfung fr Einschub

16、und HerausnahmeOn-Board-Unit (OBU) BordeinheitDedicated Short Range Communication (DSRC) Dedizierte Kurzbereich-Kommunikation (DSRC)Global System for Mobile Communication (GSM) Globales System fr Mobilkommunikation (GSM)IC card (ICC) ChipkarteInterface device ZugangsgertToxicity ToxizittTransmission

17、 protocol bertragungsprotokollApplication protocol data unit (APDU) Dateneinheit des AnwendungsprotokollsVornorm B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 EUROPEAN PRESTANDARDPRNORME EUROPENNEEUROPISCHE VORNORMENV 14062-1June 2001ICS 35.240.15English versionIdentification

18、card systemsSurface transport applicationsElectronic fee collectionPart 1: Physical characteristics, electronic signals and transmission protocolsThis European Prestandard (ENV) was approved by CEN on 10 May 2001 as a prospective standard for provisional application.The period of validity of this EN

19、V is limited initially to three years. After two years the members of CEN will be requested to submit theircomments, particularly on the question whether the ENV can be converted into a European Standard.CEN members are required to announce the existence of this ENV in the same way as for an EN and

20、to make the ENV available promptlyat national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the ENV) until the finaldecision about the possible conversion of the ENV into an EN is reached.CEN members are the national standards bodies

21、of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagemen

22、t Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. ENV 14062-1:2001 EB55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 ENV 14062-1:20012ContentsPageForeword .2Introducti

23、on 21 Scope .32 Normative references .33 Terms and definitions .44 Abbreviations 45 EFC using DSRC .55.1 Physical characteristics .55.1.1 General .55.1.2 Temperature .55.1.3 Embossing 55.1.4 Provision of contacts .55.1.5 Insertion-removal endurance 55.1.6 Toxicity 55.2 Electronic signals and electri

24、cal characteristics under normal operating conditions 65.2.1 VCC .65.2.2 CLK .65.2.3 VPP .65.3 Transmission protocols .65.3.1 General .65.3.2 Answer-To-Reset 65.3.3 Transmission bit rate .65.3.4 Protocol switching .75.3.5 Protocol Type T = 1 .75.3.6 Protocol Type T = 0 .85.3.7 Error handling protoco

25、ls 96 EFC using GSM .9Bibliography .10ForewordThis European Prestandard has been prepared by Technical Committee CEN/TC 224, Machine readable cards,related device interfaces and operations the secretariat of which is held by AFNOR.This European Prestandard comprises the following parts, under the ge

26、neral title Identification card systems Surface transport applications Electronic fee collection: Part 1: Physical characteristics, electronic signals and transmission protocols Part 2: Message requirements Part 3: Application and security aspects Part 4: Test proceduresAccording to the CEN/CENELEC

27、Internal Regulations, the national standards organizations of the followingcountries are bound to announce this European Prestandard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,Switzerl

28、and and the United Kingdom.IntroductionThis European Prestandard is one of a series of Standards describing the characteristics of IC cards used inElectronic Fee Collection (EFC) systems based on: the Dedicated Short Range Communication (DSRC); and the Global System for Mobile Communication (GSM);an

29、d the characteristics of the interface between those IC cards and the related card interface devices installed invehicles, so-called On-Board-Units.Vornorm B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 ENV 14062-1:200131 ScopeThis European Prestandard specifies directly or by

30、reference the physical characteristics, electronic signals andtransmission protocols for integrated circuit(s) cards (ICCs) carrying the EFC application and related requirementsfor On-Board-Units (OBUs) used in Electronic Fee Collection systems based on Dedicated Short RangeCommunication and Global

31、System for Mobile Communication, with the target to provide basic interoperabilitybetween an ICC and an OBU independently of the respective manufacturers and operators. It takes intoconsideration both environmental and system related aspects and states minimum requirements of conformity.The requirem

32、ents imposed by this Prestandard apply to: the IC card itself, denoted by the abbreviation ICC; the in-vehicle card interface device, denoted by the abbreviation OBU; or the combination of both.This Prestandard does not directly set requirements on any other card interface device (IFD) besides the O

33、BU e.g.stationary devices. However, the requirements imposed on the IC card may induce technical consequences for anIFD designed to accept an IC card used in EFC applications.It specifies the respective characteristics of the ICC and OBU only as far as these may concern the interface, butdoes not gi

34、ve any internal technical implementation.2 Normative referencesThis European Prestandard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated refer

35、ences, subsequent amendments to or revisions of any of these publications apply to this EuropeanPrestandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 726-3:1994, Identification card

36、 systems Telecommunications integrated circuit(s) cards and terminals Part 3: Application independent card requirements.ENV 1375-1:1994, Identification card systems Intersector integrated circuit(s) card additional formats Part 1:ID-000 card size and physical characteristics.ENV 1855:1996, Identific

37、ation card systems Intersector integrated circuit(s) card systems Tolerance ranges forIC cards.ETS 300 641, European digital cellular telecommunications system (Phase 2); Specification of the 3 VoltSubscriber Identity Module Mobile Equipment (SIM ME) interface (GSM 11.12 V 4.2.0).ETS 300 699, Europe

38、an digital cellular telecommunications system (Phase 2+) Specification of the SubscriberIdentity Module Mobile Equipment (SIM ME) interface (GSM 11.11 V 5.5.0).ISO/IEC 7810:1995, Identification cards Physical characteristics.ISO/IEC 7811-1:1995, Identification cards Recording technique Part 1: Embos

39、sing.ISO/IEC 7811-3:1995, Identification cards Recording technique Part 3: Location of embossed characters onID-1 cards.ISO/IEC 7812-1:1993, Identification cards Identification of Issuers Numbering system.ISO/IEC 7816-1:1998, Identification cards Integrated circuit(s) cards with contacts Part 1: Phy

40、sicalcharacteristics.ISO/IEC 7816-2:1999, Identification cards Integrated circuit(s) cards with contacts Part 2: Dimensions andlocation of the contacts.ISO/IEC 7816-3:1997, Identification cards Integrated circuit(s) cards with contacts Part 3: Electronic signals andtransmission protocols.ISO/IEC 781

41、6-4:1995, Identification cards Integrated circuit(s) cards with contacts Part 4: Inter-industrycommands for interchange.Vornorm B55EB1B3E14C22109E918E8EA43EDB30F09CC9B7EF8DD9NormCD - Stand 2007-03 ENV 14062-1:200143 Terms and definitionsFor the purposes of this European Prestandard, the following te

42、rms and definitions apply.3.1IC card, ICCan integrated circuit(s) card used in EFC applications3.2interface device, IFDany interface device foreseen to accept an IC card used in EFC applications3.3on-board-unit, OBUin-vehicle, card interface device, containing DRSC or GSM communication equipment, en

43、abling direct or in-directcommunication between an IC card and a roadside beacon or between an IC card and the GSM network4 AbbreviationsFor the purpose of this European Prestandard, the following abbreviations apply throughout the document unlessotherwise specified:EFC Electronic Fee CollectionAPDU

44、 Application Protocol Data Unit, according to ISO/IEC 7816-4:1995ATR Answer To ResetCLK The contact delivering the clock-signal to the ICCD Bit rate adjustment factor, as defined in ISO/IEC 7816-3:1997DSRC Dedicated Short Range CommunicationEDC Error Detection CodeEtu elementary time unit, according

45、 to ISO/IEC 7816-3:1997F Clock rate conversion factor, as defined in ISO/IEC 7816-3:1997IC Integrated circuitICC IC cardIccCurrent at the contact VCCIFD Interface DeviceINF Information Field, as defined in ISO/IEC 7816-3:1997I/O Contact used for bi-directional data exchange with the ICCLEN Length fi

46、eldNAD Node Address, as defined in ISO/IEC 7816-3:1997OBU On-Board-UnitPCB Protocol Control Byte, as defined in ISO/IEC 7816-3:1997PPS Protocol and Parameters Selection, as defined in ISO/IEC 7816-3:1997RST Contact delivering the reset-signal to the ICCTPDU Transport Protocol Data Unit, according to ISO/IEC 7816-3:1997VccSupply voltage at VCCVCC Contact delivering the supply voltage to the ICCVppProgramming voltage at VPPVPP Contact for delivering programming voltage to the ICCVornorm B55EB1B3E14C22109E918E8EA43EDB30F09C