DIN ISO 8693-2012 Tools for moulding - Flat ejector pins (ISO 8693 2011)《注塑工具 矩形顶杆 (ISO 8693-2011)》.pdf

《DIN ISO 8693-2012 Tools for moulding - Flat ejector pins (ISO 8693 2011)《注塑工具 矩形顶杆 (ISO 8693-2011)》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 8693-2012 Tools for moulding - Flat ejector pins (ISO 8693 2011)《注塑工具 矩形顶杆 (ISO 8693-2011)》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、July 2012 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25

2、.120.30!$(“1900525www.din.deDDIN ISO 8693Tools for moulding Flat ejector pins (ISO 8693:2011)English translation of DIN ISO 8693:2012-07Press-, Spritzgie- und Druckgiewerkzeuge Flachauswerfer (ISO 8693:2011)Englische bersetzung von DIN ISO 8693:2012-07Outillage de moulage jecteurs lames (ISO 8693:20

3、11)Traduction anglaise de DIN ISO 8693:2012-07SupersedesDIN ISO 8693:2000-08www.beuth.deDocument comprises 9 pagesIn case of doubt, the German-language original shall be considered authoritative.06.12 DIN ISO 8693:2012-07 2 A comma is used as the decimal marker. Contents Page National foreword .3 Na

4、tional Annex NA (informative) Bibliography 3 1 Scope 4 2 Dimensions .4 3 Material and hardness .7 4 Designation 8 Bibliography 9 DIN ISO 8693:2012-07 3 National foreword This standard has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 8 “Tools for pressing and moulding

5、”. The responsible German body involved in its preparation was the Normenausschuss Werkzeuge und Spann-zeuge (Tools and Clamping Devices Standards Committee), Working Committee NA 121-03-03 AA Press-, Spritzgie- und Druckgiewerkzeuge. Attention is drawn to the possibility that some of the elements o

6、f this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. The DIN Standard corresponding to the International Standards referred to in this document is as follows: ISO 1302:2002 DIN EN ISO 1302:2002-06 Amendments This standa

7、rd differs from DIN ISO 8693:2000-08 as follows: a) the indication of surface texture has been brought in line with ISO 1302:2002-06; b) the Bibliography has been updated; c) Figure 1 and the key have been revised; d) the standard has been editorially revised. Previous editions DIN 1530-4: 1988-10 D

8、IN ISO 8693: 2000-08 National Annex NA (informative) Bibliography DIN 1530-1, Tools for moulding Part 1: Ejector pins with cylindrical head DIN 1530-2, Tools for moulding Part 2: Shouldered ejector pins DIN EN ISO 1302:2002-06, Geometrical Product Specifications (GPS) Indication of surface texture i

9、n technical product documentation Tools for moulding Flat ejector pins 1 Scope This International Standard specifies the dimensions and tolerances, in millimetres, of flat ejector pins which are used in compression and injection moulds and in die casting dies. It also gives material guidelines and h

10、ardness requirements, and specifies the designation of flat ejector pins. Ejector pins with cylindrical head are specified in ISO 6751; shouldered ejector pins are specified in ISO 8694. 2 Dimensions The dimensions of flat ejector pins shall be in accordance with the indications of Figure 1 and Tabl

11、es 1 and 2. DIN ISO 8693:2012-07 4Surface roughness values in micrometres Key 1 edges without burrs 2 gauge plane 2 3 gauge plane 1 aRa 0,8 for hot worked steel. Ra 0,4 for alloyed cold worked steel. bIt is permitted to provide the ejector pin with an alternative surface roughness or a small variati

12、on on the diameter, D1, for a certain length. cSee note a to Tables 1 and 2. Figure 1 Flat ejector pins DIN ISO 8693:2012-07 5Table 1 Flat ejector pins of hot worked steel Dimensions in millimetres D1h11 D200,2aa00,015ba00,015L1 20H 00,05R 0,2063 80 100 125 160 200 250 315 400 L2 12 32 40 50 63 80 1

13、00 125 160 200 4 8 0,8 3,5 X X X X 3 0,3 1 X X X X 4,2 3,8 X X X X 4 1,2 3,5 X X X X 4,2 3,8 X X X X 5 10 1 4,5 X X X X 1,2 X X X 6 12 1,5 5,5 X X X X 5 0,5 2 X X X 8 14 1,5 7,5 X X X X 2 X X X 10 16 1,5 9,5 X X X 2 X X X X 12 18 2 11,5 X X X X 7 0,8 2,5 X X X X 16 22 2 15,5 X X X X 2,5 X X X X aThe

14、se limit dimensions apply to 100 mm length. For lengths greater than 100 mm, the limit deviations shall be multiplied by (L1 L2) 10-2. The dimensional tolerance is at its maximum at gauge plane 2. DIN ISO 8693:2012-07 6Table 2 Flat ejector pins of alloyed cold worked steel Dimensions in millimetres

15、D1h11 D2 00,2aa00,015ba00,015L1 20H 00,05R 0,2063 80 100 125 160 200 250 315 L2 1232 40 50 63 80 100 125 160 4 8 0,8 3,5 X X X X 3 0,3 1 X X X X 4,2 3,8 4 1,2 3,5 X X X X 4,2 3,8 5 10 1 4,5 X X X X 1,2 X X X 6 12 1,5 5,5 X X X X 5 0,5 2 X X X 8 14 1,5 7,5 X X X X 2 X X X 10 16 1,5 9,5 X X X 2 X X X

16、12 18 2 11,5 X X X 7 0,8 2,5 X X X aThese limit dimensions apply to 100 mm length. For lengths greater than 100 mm, the limit deviations shall be multiplied by(L1 L2) 10-2. The dimensional tolerance is at its maximum at gauge plane 2. 3 Material and hardness Flat ejector pins shall be made of hot wo

17、rked steel or alloyed cold worked steel. The hardness of the shaft and head shall conform to the indication of Table 3. DIN ISO 8693:2012-07 7Table 3 Material and hardness Material HardnessaShaft Head Hot worked steel Min. 1 400 MPa core strength min. 950 HV 0,3 (45 5) HRC hot-forged Alloyed cold wo

18、rked steel (60 2) HRC aThe point at which hardness is measured is left to the manufacturers discretion. 4 Designation Flat ejector pins according to this International Standard shall be designated by: a) “Flat ejector pin”; b) reference to this International Standard, i.e. ISO 8693; c) the width, a,

19、 and thickness, b, in millimetres; d) the length, L1, in millimetres; e) the material. EXAMPLE A flat ejector pin with width a = 0,8 mm, thickness b = 3,5 mm, length L1= 63 mm and made of hot worked steel is designated as follows: Flat ejector pin ISO 8693 - 0,8 3,5 - 63 - Hot worked steel DIN ISO 8693:2012-07 8Bibliography 1 ISO 1302:2002, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation 2 ISO 6751, Tools for moulding Ejector pins with cylindrical head 3 ISO 8694, Tools for moulding Shouldered ejector pins DIN ISO 8693:2012-07 9