DIN ISO 6987-2014 Indexable hard material inserts with rounded corners with partly cylindrical fixing hole - Dimensions (ISO 6987 2012)《有部分圆柱形固定孔和圆角的可转位硬质合金刀片 尺寸规格(ISO 6987-2012)》.pdf

《DIN ISO 6987-2014 Indexable hard material inserts with rounded corners with partly cylindrical fixing hole - Dimensions (ISO 6987 2012)《有部分圆柱形固定孔和圆角的可转位硬质合金刀片 尺寸规格(ISO 6987-2012)》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 6987-2014 Indexable hard material inserts with rounded corners with partly cylindrical fixing hole - Dimensions (ISO 6987 2012)《有部分圆柱形固定孔和圆角的可转位硬质合金刀片 尺寸规格(ISO 6987-2012)》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、February 2014 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 25.100.01!%,Ba“2093162www.din.deDDIN ISO 6987Indexable hard material inserts with rounded corners, with partlycylindrical fixing hole Dimensions (ISO 6987:2012),English translation of DIN ISO 6987:2014-02Wendeschneidplatten aus Hartmetall mit Eckenrundungen und teilweise zylindrischerBefestigungs

3、bohrung Mae (ISO 6987:2012),Englische bersetzung von DIN ISO 6987:2014-02Plaquettes amovibles en matriaux durs avec arrondi de pointe et trou de fixationpartiellement cylindrique Dimensions (ISO 6987:2012),Traduction anglaise de DIN ISO 6987:2014-02SupersedesDIN ISO 6987:2003-07 andDIN ISO 6987 Corr

4、igendum 1:2003-09www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 27 pages02.14 A comma is used as the decimal marker. Contents Page National foreword .3 National Annex NA (informative) Bibliography .4 1 Scope .5 2 Normative references .

5、5 3 Types of inserts 5 4 Interchangeability .6 4.1 Tolerances .6 4.2 Thickness, s, of inserts with chip breakers 6 4.3 Fixing hole .6 5 Designation and marking .7 5.1 Designation .7 5.2 Marking 8 6 Measurement.8 7 Recommended dimensions .8 7.1 Triangular inserts TC .8 7.2 Triangular inserts TP .9 7.

6、3 Square inserts SC . 10 7.4 Square inserts SP 11 7.5 Rhombic inserts with 80 included angle CC . 12 7.6 Rhombic inserts with 80 included angle CP . 13 7.7 Rhombic inserts with 55 included angle DC . 14 7.8 Rhombic inserts with 35 included angle VB and VC . 15 7.9 Round inserts RC 16 7.10 Round inse

7、rts RP 16 7.11 Hexagonal (trigon) inserts with 80 included angle WC . 17 Annex A (normative) Tolerances for d, m, m1, m2and s Extract from ISO 1832 18 Annex B (normative) Methods of measurement of dimension m 20 B.1 Triangular inserts . 20 B.2 Square inserts 20 B.3 Rhombic inserts . 21 B.4 Round ins

8、erts . 21 B.5 Hexagonal inserts 22 Annex C (normative) Size ranges 23 Annex D (informative) Relationship between designations in this International Standard and the ISO 13399 series 26 D.1 Relationship between designations 26 Bibliography . 27 2DIN ISO 6987:2014-02National foreword This document (IS

9、O 6987:2012) has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 9 “Tools with cutting edges made of hard cutting materials” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Werkzeuge und Spannzeuge (Tools and

10、Clamping Devices Standards Committee), Working Committee NA 121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held r

11、esponsible for identifying any or all such patent rights. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 513 DIN ISO 513 ISO 1832 DIN ISO 1832 Amendments This standard differs from DIN ISO 6987:2003-07 and DIN ISO 6987 Corrigendum 1:20

12、03-09 as follows: a) (German version only) Corrigendum 1:2003 has been incorporated; b) normative references have been updated; c) Figures 8, 9 and 11 have been revised; d) footnote b in Table A.1 has been deleted; e) Annex D “Relationship between designations in this International Standard and the

13、ISO 13399 series” has been added; f) the Bibliography has been updated; g) the standard has been editorially revised. Previous editions DIN 4967-1: 1987-04 DIN 4967-2: 1993-11 DIN ISO 6987: 2003-07 DIN ISO 6987 Corrigendum 1: 2003-09 3DIN ISO 6987:2014-02National Annex NA (informative) Bibliography

14、DIN ISO 513, Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of application DIN ISO 1832, Indexable inserts for cutting tools Designation 4DIN ISO 6987:2014-021 ScopeThis International Standard specifies

15、the dimensions of hard material inserts with rounded corners and with a partly cylindrical fixing hole. These inserts are primarily intended to be mounted on turning and boring tools using a countersunk head screw or any other fixing element, such as a pin lock.2 Normative referencesThe following re

16、ferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 513, Classification and application of hard cutting materials

17、for metal removal with defined cutting edges Designation of the main groups and groups of applicationISO 1832, Indexable inserts for cutting tools Designation3 Types of insertsThe types of indexable hard material insert specified in this International Standard are the following: TC: triangular inser

18、ts, with 7 normal clearance; TP: triangular inserts, with 11 normal clearance; SC: square inserts, with 7 normal clearance; SP: square inserts, with 11 normal clearance; CC: rhombic inserts, with 7 normal clearance and 80 included angle; CP: rhombic inserts, with 11 normal clearance and 80 included

19、angle; DC: rhombic inserts, with 7 normal clearance and 55 included angle; VB: rhombic inserts, with 5 normal clearance and 35 included angle; VC: rhombic inserts, with 7 normal clearance and 35 included angle; RC: round inserts, with 7 normal clearance; RP: round inserts, with 11 normal clearance;

20、WC: hexagonal (trigon) inserts, with 7 normal clearance and 80 included angle.Inserts dealt with in this International Standard are standardized with chip breakers on the face (designated by the letter T) and without chip breakers (designated by the letter W).Neither the shape nor the dimensions of

21、chip breakers are standardized. Thus, if necessary, special features shall be explained with a diagram or additional specifications.Tables C.1 to C.4 give the range of sizes for these inserts.Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions 5DIN IS

22、O 6987:2014-024 Interchangeability4.1 TolerancesThe indexable hard material inserts which are the subject of this International Standard are provided in tolerance class M and for VC-shape inserts also in tolerance class G in accordance with ISO 1832.The values of tolerance class G are in accordance

23、with ISO 1832 and the values of tolerance class M are given in Annex A.Other tolerances are included in Table 1 for hole dimensions and in Tables 3 to 12 for insert dimensions.4.2 Thickness, s, of inserts with chip breakersThe thickness, s, of inserts with chip breakers is defined as the distance be

24、tween the cutting edge at the corner and the supporting surface of the insert; see Figure 1.Figure 1 Thickness of inserts with chip breakers 4.3 Fixing holeIn order to guarantee interchangeability when mounting the insert by a countersunk head screw having a head taper angle between 40 and 60, the f

25、orm of the hole is partly cylindrical and its dimensions are related to the diameter of the inscribed circle of the insert. Figure 2 and Table 1 give the elements of definition of the fixing hole.The position of point P is given by diameter d2(see Table 1), the distance t, measured from the cutting

26、edge at the corner and dimension c, measured from the upper face.The ranges of dimensions t and c are as follows:0,05 d1 t 0,3 d1and0,15 d1 c 0,3 d1These dimensions take into account three cases: indexable inserts with upper faces below the cutting edges see Figure 2 a); with upper faces on the same

27、 level as the cutting edges see Figure 2 b); with upper faces above the cutting edges see Figure 2 c).The dimensions of t and c shall be satisfied in all three cases.The diameter, d1, of the cylindrical part of the hole is given in Table 1.6DIN ISO 6987:2014-02The part of the profile between d1and P

28、 is left to the manufacturers discretion, but shall satisfy the following requirements: the use of screws with head taper angle, , of between 40 and 60 shall be possible; the angle of the tangent theoretical taper at point P has the value of 65; the distance between the contact line with a screw hav

29、ing a 40 head taper angle and the contact line with a screw having a 60 head taper angle shall be as small as possible.The part of the profile above point P is left to the manufacturers discretion.Figure 2 Fixing holeTable 1 Dimensions of the holeDimensions in millimetresdFor insert shapeT, S, C, D,

30、 V, W4,76 5,56 6,35 7,94 9,525 12,7 15,875 19,05 25,4 R 6 8 10/12 16 20 25 32d1JS13 2,15 2,5 2,8 3,4 4,4 5,5 5,5 6,5 8,6 8,6d2JS13 2,7 3,3 3,75 4,5 6 7,5 7,5 9 12 125 Designation and marking5.1 DesignationThe designation of the indexable hard material inserts which form the subject of this Internati

31、onal Standard shall conform to ISO 1832.In addition to this designation, one or both of the following may be indicated: the symbol of the group of application, in accordance with ISO 513; the commercial designation of the hard material grade.7DIN ISO 6987:2014-025.2 MarkingThe following symbol, at l

32、east, shall be marked on the insert itself (except when this is difficult to carry out on small inserts): symbol of the group of application, or commercial designation of the hard material grade, or both, if possible, on large inserts.6 MeasurementAnnex B indicates the methods of measuring the dimen

33、sion m of the indexable inserts covered by this International Standard.7 Recommended dimensionsThe choice of the more common dimensions is restricted to the values given in Tables 3 to 12. It is strongly recommended that these standard inserts be used wherever possible (first preference). When other

34、 inserts are required, their dimensions shall be selected from the non-shaded areas of Tables C.1 to C.4 (second preference). Inserts having dimensions given in the shaded areas of this table are not recommended.NOTE The m dimensions are calculated using the exact values of the corner radius, r, giv

35、en in Table 2, rounded to the third decimal place.Table 2 Exact values of rDesignation of r02 04 08 12 16 20 24 32Exact value of r, mm0,203 2a0,397 0,794 1,191 1,588 1,984 2,381 3,175aRounded to the fourth decimal place.7.1 Triangular inserts TCa) TCMW without chip breakers b) TCMT with chip breaker

36、sFigure 3 Triangular inserts TC8DIN ISO 6987:2014-02Table 3 Dimensions of triangular inserts TCDimensions in millimetresInsertldasamar 0,1d1JS13TCMW 090204 TCMT 090204 9,6 5,562,387,943 0,4 2,5TCMW 110202 TCMT 11020211 6,359,322 0,22,8TCMW 110204 TCMT 110204 9,128 0,4TCMW 130304 TCMT 13030413,6 7,94

37、 3,1811,51 0,43,4TCMW 130308 TCMT 130308 11,113 0,8TCMW 16T304 TCMT 16T30416,5 9,525 3,9713,891 0,44,4TCMW 16T308 TCMT 16T308 13,494 0,8TCMW 16T312 TCMT 16T312 13,097 1,2TCMW 220404 TCMT 22040422 12,7 4,7618,653 0,45,5TCMW 220408 TCMT 220408 18,256 0,8TCMW 220412 TCMT 220412 17,859 1,2TCMW 220416 TC

38、MT 220416 17,463 1,6aTolerances on d, s and m in accordance with ISO 1832. See Annex A.7.2 Triangular inserts TPa) TPMW without chip breakers b) TPMT with chip breakersFigure 4 Triangular inserts TP9DIN ISO 6987:2014-02Table 4 Dimensions of triangular inserts TPDimensions in millimetresInsertldasama

39、r 0,1d1JS13TPMW 090202 TPMT 0902029,6 5,56 2,388,131 0,22,5TPMW 090204 TPMT 090204 7,943 0,4TPMW 110202 TPMT 11020211 6,35 2,389,322 0,22,8TPMW 110204 TPMT 110204 9,128 0,4TPMW 130304 TPMT 13030413,6 7,94 3,1811,51 0,43,4TPMW 130308 TPMT 130308 11,113 0,8TPMW 16T304 TPMT 16T30416,5 9,525 3,9713,891

40、0,44,4TPMW 16T308 TPMT 16T308 13,494 0,8aTolerances on d, s and m in accordance with ISO 1832. See Annex A.7.3 Square inserts SCa) SCMW without chip breakers b) SCMT with chip breakersFigure 5 Square inserts SC10DIN ISO 6987:2014-02Table 5 Dimensions of square inserts SCDimensions in millimetresInse

41、rt dasamar 0,1d1JS13SCMW 09T304 SCMT 09T3049,525 3,971,808 0,44,4SCMW 09T308 SCMT 09T308 1,644 0,8SCMW 120404 SCMT 12040412,7 4,762,466 0,45,5SCMW 120408 SCMT 120408 2,301 0,8SCMW 120412 SCMT 120412 2,137 1,2SCMW 150512 SCMT 15051215,875 5,562,795 1,25,5SCMW 150516 SCMT 150516 2,63 1,6SCMW 190612 SC

42、MT 19061219,05 6,353,452 1,26,5SCMW 190616 SCMT 190616 3,288 1,6SCMW 190624 SCMT 190624 2,959 2,4aTolerances on d, s and m in accordance with ISO 1832. See Annex A.7.4 Square inserts SPa) SPMW without chip breakers b) SPMT with chip breakersFigure 6 Square inserts SPTable 6 Dimensions of square inse

43、rts SPDimensions in millimetresInsert dasamar 0,1d1JS13SPMW 090304 SPMT 0903049,525 3,181,808 0,44,4SPMW 090308 SPMT 090308 1,644 0,8SPMW 09T304 SPMT 09T3049,525 3,971,808 0,44,4SPMW 09T308 SPMT 09T308 1,644 0,8aTolerances on d, s and m in accordance with ISO 1832. See Annex A.11DIN ISO 6987:2014-02

44、7.5 Rhombic inserts with 80 included angle CCa) CCMW without chip breakers b) CCMT with chip breakersFigure 7 Rhombic inserts with 80 included angle CCTable 7 Dimensions of rhombic inserts with 80 included angle CCDimensions in millimetresInsertldasam1am2ar 0,1d1JS13CCMW 060202 CCMT 0602026,4 6,35 2

45、,381,652 0,908 0,22,8CCMW 060204 CCMT 060204 1,544 0,848 0,4CCMW 080304 CCMT 0803048,1 7,94 3,181,986 1,091 0,43,4CCMW 080308 CCMT 080308 1,765 0,97 0,8CCMW 09T304 CCMT 09T3049,7 9,525 3,972,426 1,333 0,44,4CCMW 09T308 CCMT 09T308 2,206 1,212 0,8CCMW 120404 CCMT 12040412,9 12,7 4,763,308 1,818 0,45,

46、5CCMW 120408 CCMT 120408 3,088 1,697 0,8CCMW 120412 CCMT 120412 2,867 1,576 1,2CCMW 160512 CCMT 16051216,1 15,875 5,563,749 2,061 1,25,5CCMW 160516 CCMT 160516 3,529 1,939 1,6CCMW 190612 CCMT 19051219,3 19,05 6,354,632 2,545 1,26,5CCMW 190616 CCMT 190616 4,411 2,424 1,6CCMW 190624 CCMT 190624 3,97 2

47、,182 2,4aTolerances on d, s, m1and m2in accordance with ISO 1832. See Annex A.12DIN ISO 6987:2014-027.6 Rhombic inserts with 80 included angle CPa) CPMW without chip breakers b) CPMT with chip breakersFigure 8 Rhombic inserts with 80 included angle CPTable 8 Dimensions of rhombic inserts with 80 inc

48、luded angle CPDimensions in millimetresInsertldasam1am2ar 0,1d1JS13CPMW 04T102 CPMT 04T1024,8 4,76 1,981,21 0,665 0,22,15CPMW 04T104 CPMT 04T104 1,102 0,606 0,4CPMW 050202 CPMT 0502025,6 5,56 2,381,432 0,787 0,22,5CPMW 050204 CPMT 050204 1,324 0,728 0,4CPMW 060202 CPMT 0602026,4 6,35 2,381,652 0,908 0,22,8CPMW 060204 CPMT 060204 1,544 0,848 0,4CPMW 080304 CPMT 0803048,1 7,94 3,181,986 1,091 0,43,4CPMW 080308 CPMT 080308 1,765 0,97 0,8CPMW 090304 CPMT 0903049,7 9,525 3,182,426 1,333 0,44,4CPMW 090308 CPMT 090308 2,206 1,212 0,8CPMW 09T304 CPMT 09T3049,7 9,525 3,972,426 1,333 0,44,