DIN ISO 5456-2-1998 Technical drawings - Projection methods - Part 2 Orthographic representations (ISO 5456-2 1996)《技术图纸 投影法 第2部分 正交表示法(ISO 5456-2 1996)》.pdf
《DIN ISO 5456-2-1998 Technical drawings - Projection methods - Part 2 Orthographic representations (ISO 5456-2 1996)《技术图纸 投影法 第2部分 正交表示法(ISO 5456-2 1996)》.pdf》由会员分享,可在线阅读,更多相关《DIN ISO 5456-2-1998 Technical drawings - Projection methods - Part 2 Orthographic representations (ISO 5456-2 1996)《技术图纸 投影法 第2部分 正交表示法(ISO 5456-2 1996)》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、DEUTSCHE NORM Airil 1998 Technical drawings - Projection methods Part 2: Orthographic representations (IS0 5456-2 : 1996) DIN IS0 5456-2 ICs 01.1 00.01 Descriptors: Drawings, projection methods. Supersedes parts of DIN 6-1, December 1986 edition. Technische Zeichnungen - Projektionsmethoden -Teil 2:
2、 Orthogonale Darstellungen (IS0 5456-2 : 1996) This standard incorporates International Standard IS0 5456-2 Technical drawings - Projection methods - Part 2: Orthographic representations. A comma is used as the decimal marker. National foreword This standard has been prepared by ISO/TC 1 O. The resp
3、onsible German body involved in its preparation was the Normenausschu Technische Produkt- dokumentation (Technical Product Documentation Standards Committee). The DIN Standards corresponding to the International Standards referred to in clause 2 of the IS0 Standard are as follows: IS0 Standard DIN S
4、tandards IS0 128 DIN 6-1, DIN 6-2, DIN 15-2, DIN 201, DIN IS0 128-20, DIN IS0 128-21, and DIN IS0 10209-2 IS0 129 IS0 3098-1 DIN 6776-1 IS0 3461 -2 DIN 32830-20*) IS0 5456-1 DIN IS0 5456-1 DIN 406-1 O, DIN 406-1 1 IS0 10209-1 DIN 199-1 and DIN 199-2 IS0 10209-2 DIN IS0 10209-2 Amendments Parts of DI
5、N 6-1, December 1986 edition, have been superseded by the specifications of DIN IS0 5456-2. Previous editions DIN 36: 1922-10; DIN 6: 1922-1 1, 1956-10, 1968-03; DIN 6-1 : 1986-12. *) At present at the stage of draft. Continued overleaf. IS0 Standard comprises 7 pages. No pari of this standard may b
6、e reproduced without the prior permission of Ref. No. DIN IS0 5456-2 : 1998-0 Y Deutsches Institut fr Normung e. V., Berlin. wth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen). English price group 08 Sales No. 0408 10.98 Page 2 DIN IS0 5456-2 : 1998-04
7、 National Annex NA Standards referred to (and not included in Normative references) DIN 6-1 DIN 6-2 DIN 15-2 DIN 199-1 DIN 199-2 DIN 201 DIN 406-1 O DIN 406-1 1 DIN 1356-1 DIN 6776-1 DIN 32830-20 Technical drawings - Representation in normal projection -Views and special representations Technical dr
8、awings - Representation in normal projection - Sectional views Technical drawings - Lines - General application Terminology associated with drawings and item lists - Drawings Terminology associated with drawings and parts lists - Parts lists Technical drawings - Hatching to indicate sections Enginee
9、ring drawing practice - Dimensioning - Concepts and general principles Engineering drawing practice - Dimensioning - Principles of application Construction drawings - Types and principles of representation Technical drawings - Lettering - Characters Principles for the creation of graphical symbols -
10、 Graphical symbols for use in technical prod- uct documentation Page 1 IS0 5456-2 : 1996 Technical drawings - Projection methods Part 2: Orthographic representations Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member b
11、odies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be rep- resented on that committee. International organizations, governmental
12、 and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (I EC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the membe
13、r bodies for voting. Publication as an International Standard requires approval by at least 75 YO of the member bodies casting a vote. International Standard IS0 5456-2 was prepared by Technical Committee ISO/TC 1 O, Technical drawings, product definition and related documen- tation, Subcommittee SC
14、 1, Basic conventions. IS0 5456 consists of the following parts, under the general title Technical drawings - Projection methods: - Part 7: Synopsis - Part 2: Orthographic representations - Part 3: Axonometric representations - Part 4: Central projection Annex A forms an integral part of this part o
15、f IS0 5456. Page 2 IS0 5456-2 : 1996 Introduction 1 Scope Orthographic representation in its various forms is the most widely used method of representing technical objects in all fields of technical drawing (mechanical, electrical, construction, etc.), and is thus considered to be the accepted techn
16、ical language. This part of IS0 5456 specifies basic rules for the application of orthographic representation to all types of technical drawings in all technical fields, according to the general rules specified in IS0 128, IS0 129, IS0 3098-1, IS0 3461-2 and IS0 5456-1. 2 Normative references The fo
17、llowing standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 5456. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 5456 are encouraged to
18、 investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 1 28:1982, Technical drawings - General prin- ciples of presentation. IS0 1 29: 1985, Technical drawings - Dim
19、ensioning - General principles, definitions, methods of execution and special indications. IS0 3098-1 :1974, Technical drawings - lettering - Part 1: Currently used characters. IS0 3461 -2: 1 987, General principles for the creation of graphical symbols - Part 2: Graphical symbols for use in technic
20、al product documentation. IS0 5456-1 :I 996, Technical drawings - Projection methods - Part 1: Synopsis. IS0 10209-1 : 1992, Technical product documentation - Vocabulary - Part : Terms relating to technical drawings: general and types of drawings. IS0 10209-2:1993, Technical product documentation -
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DINISO545621998TECHNICALDRAWINGSPROJECTIONMETHODSPART2ORTHOGRAPHICREPRESENTATIONSISO545621996 技术 图纸 投影

链接地址:http://www.mydoc123.com/p-684675.html