DIN ISO 13373-1-2002 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 1 General procedures (ISO 13373-1 2002)《机械设备的条件监测和诊断 振动条件监测 第1部分 一般程序 .pdf

《DIN ISO 13373-1-2002 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 1 General procedures (ISO 13373-1 2002)《机械设备的条件监测和诊断 振动条件监测 第1部分 一般程序 .pdf》由会员分享，可在线阅读，更多相关《DIN ISO 13373-1-2002 Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 1 General procedures (ISO 13373-1 2002)《机械设备的条件监测和诊断 振动条件监测 第1部分 一般程序 .pdf（57页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 17.160Zustandsberwachung und -diagnostik von Maschinen Schwingungs-Zustandsberwachung Teil 1: Allgemeine Anleitungen(ISO 13373-1 : 2002)Ref. No. DIN ISO 13373-1 : 2002-07English price group 20 Sales No. 042011.02DEUTSCHE NORM July 2002ISO 13373-1Continued overleaf.ISO Standard comprises 55 pages

2、. No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e.V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).Condition monitoring and diagnostics ofmachines Vibration condition m

3、onitoringPart 1: General procedures(ISO 13373-1 : 2002)This standard incorporates International StandardISO 13373-1 Condition monitoring and diagnostics of machines Vibration condition monitoring Part 1:General procedures.A comma is used as the decimal marker.National forewordThis standard has been

4、prepared by ISO/TC 108 Mechanical vibration and shock.The responsible German body involved in its preparation was the Normenausschuss Akustik, Lrm-minderung und Schwingungstechnik (Acoustics, Noise Control and Vibration Engineering Standards Com-mittee), Technical Committee Schwingungsberwachung.The

5、 DIN Standards corresponding to the International Standards and the IEC Publication referred to inclause 2 and in the bibliography of the ISO Standard are as follows:IEC Publication/ DIN StandardISO StandardIEC 60034-14 DIN EN 60034-14ISO 1925 DIN ISO 1925ISO 2041 Supplement 1 to DIN 1311*)ISO 5348

6、DIN ISO 5348ISO 7919-1 DIN ISO 7919-1ISO 7919-2 DIN ISO 7919-2ISO 7919-3 DIN ISO 7919-3ISO 7919-4 DIN ISO 7919-4ISO 10816-1 DIN ISO 10816-1*) Currently at draft stage.Page 2DIN ISO 13373-1 : 2002-07ISO 10816-2 DIN ISO 10816-2ISO 10816-3 DIN ISO 10816-3ISO 10816-4 DIN ISO 10816-4ISO 10816-6 DIN ISO 1

7、0816-6ISO 10817-1 DIN ISO 10817-1National Annex NAStandards referred to(and not included in Normative references and Bibliography)DIN EN 60034-14 Rotating electrical machines Part 14: Mechanical vibration of certain machines with shaftheights 56 mm and higher Measurement, evaluation and limits of vi

8、bration(IEC 34-14 : 1996)DIN ISO 5348 Mechanical vibration and shock Mechanical mounting of accelerometers (ISO 5348 : 1998)DIN ISO 7919-1 Mechanical vibration of non-reciprocating machines Measurements on rotating shafts andevaluation criteria Part 1: General guidelines (ISO 7919-1 : 1996)DIN ISO 7

9、919-2 Mechanical vibration of non-reciprocating machines Measurements on rotating shafts andevaluation criteria Part 2: Large land-based steam turbine generator sets(ISO 7919-2 : 1996)DIN ISO 7919-3 Mechanical vibration of non-reciprocating machines Measurements on rotating shafts andevaluation crit

10、eria Part 3: Coupled industrial machines (ISO 7919-3 : 1996)DIN ISO 10816-1 Evaluation of machine vibration by measurements on non-rotating parts Part 1: Generalguidelines (ISO 10816-1 : 1995)DIN ISO 10816-2 Evaluation of machine vibration by measurements on non-rotating parts Part 2: Largeland-base

11、d steam turbine generator sets in excess of 50 MW (ISO 10816-2 : 1996)DIN ISO 10816-3 Evaluation of machine vibration by measurements on non-rotating parts Part 3: Industrialmachines with nominal power above 15 kW and nominal speeds between 120 r/min and15 000 r/min when measured in situ (ISO 10816-

12、3 : 1998)DIN ISO 10816-4 Evaluation of machine vibration by measurements on non-rotating parts Part 4: Gas tur-bine driven sets excluding aircraft derivatives (ISO 10816-4 : 1998)DIN ISO 10816-6 Evaluation of machine vibration by measurements on non-rotating parts Part 6: Recipro-cating machines wit

13、h power ratings above 100 kW (ISO 10816-6 : 1995)Page 1ISO 13373-1 : 2002Condition monitoring and diagnostics of machines Vibration conditionmonitoringPart 1: General procedures2356666679111111181920202024252525273234343541434654Page 2ISO 13373-1 : 2002Page 3ISO 13373-1 : 2002Page 4ISO 13373-1 : 200

14、2Page 5ISO 13373-1 : 2002Page 6ISO 13373-1 : 2002Page 7ISO 13373-1 : 2002Page 8ISO 13373-1 : 2002Page 9ISO 13373-1 : 2002Page 10ISO 13373-1 : 2002Page 11ISO 13373-1 : 2002Page 12ISO 13373-1 : 2002Page 13ISO 13373-1 : 2002Page 14ISO 13373-1 : 2002Page 15ISO 13373-1 : 2002Page 16ISO 13373-1 : 2002Page 17ISO 13373-1 : 2002Page 18ISO 13373-1 : 2002Page 19ISO 13373-1 : 2002Page 20ISO 13373-1 : 2002Page 21ISO 13373-1 : 2002Page 22ISO 13373-1 : 2002Page 23ISO 13373-1 : 2002Page 24ISO 13373-1 : 2002Page 25ISO 13373-1 : 2002Page 26ISO 13373-1 : 2002Page 27ISO 13373-1 : 2002Page 28ISO 13373-1 : 2002