DIN ISO 11093-5-2017 Paper and board - Testing of cores - Part 5 Determination of characteristics of concentric rotation (ISO 11093-5 2016)《纸和纸板 卷轴芯试验 第5部分 同心旋转特性测定(ISO 11093-5-201.pdf

《DIN ISO 11093-5-2017 Paper and board - Testing of cores - Part 5 Determination of characteristics of concentric rotation (ISO 11093-5 2016)《纸和纸板 卷轴芯试验 第5部分 同心旋转特性测定(ISO 11093-5-201.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 11093-5-2017 Paper and board - Testing of cores - Part 5 Determination of characteristics of concentric rotation (ISO 11093-5 2016)《纸和纸板 卷轴芯试验 第5部分 同心旋转特性测定(ISO 11093-5-201.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、May 2017 English price group 6No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 85.080.30!%eC#“2663200www.din.deDIN I

2、SO 11093-5Paper and board Testing of cores Part 5: Determination of characteristics of concentric rotation (ISO 110935:2016),English translation of DIN ISO 11093-5:2017-05Papier und Pappe Prfung von Wickelkernen aus Hlsenkarton Teil 5: Bestimmung der Rundlaufeigenschaften (ISO 110935:2016),Englische

3、 bersetzung von DIN ISO 11093-5:2017-05Papier et carton Essais des mandrins Partie 5: Dtermination des caractristiques de rotation (ISO 110935:2016),Traduction anglaise de DIN ISO 11093-5:2017-05SupersedesDIN ISO 110935:201008www.beuth.deDocument comprises 8 pagesDTranslation by DIN-Sprachendienst.I

4、n case of doubt, the German-language original shall be considered authoritative.06.17 DIN ISO 11093-5:2017-05 A comma is used as the decimal marker. Contents Page National foreword . 3 National Annex NA (informative) Bibliography 3 Foreword 4 1 Scope 5 2 Normative references 5 3 Principles . 5 3.1 D

5、etermination of roundness deviation (fR) by three-point measurement 5 3.2 Determination of the straightness deviation (fS) by five-point measurement . 5 4 Apparatus . 5 5 Preparation of test pieces 6 5.1 Sampling . 6 5.2 Test pieces . 6 5.3 Conditioning of test pieces . 6 6 Measuring procedure 7 6.1

6、 General 7 6.2 Positioning of the support . 7 6.3 Measuring of roundness deviation . 7 6.4 Measuring of straightness deviation 7 6.4.1 Straightness deviation . 7 6.4.2 Precision of the measurement system 7 7 Calculation . 8 8 Test report . 8 2 DIN ISO 11093-5:2017-05 National foreword This document

7、(ISO 11093-5:2016) has been prepared by Technical Committee ISO/TC 6 “Paper, board and pulps” (Secretariat: SCC, Canada). The responsible German body involved in its preparation was DIN-Normenausschuss Papier, Pappe und Faserstoff (DIN Standards Committee Paper, Board and Pulps), Working Committee N

8、A 074-01-41 AA “Cylindrical cores of paper and board for reels”. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 11093-1 DIN ISO 11093-1 ISO 11093-2 DIN ISO 11093-2 Amendments This standard differs from DIN ISO 11093-5:2010-08 as follow

9、s: a) 6.4 “Measuring of straightness deviation” has been technically revised; b) in 6.4.1, a new equation for measuring the straightness deviation has been included; c) in 6.4.2, a new equation for precision of the measurement system has been introduced; d) the standard has been editorially revised.

10、 Previous editions DIN 54530-5: 1993-07 DIN EN ISO 11093-5: 1998-03, 2010-08 National Annex NA (informative) Bibliography DIN ISO 11093-1, Paper and board Testing of cores Part 1: Sampling DIN ISO 11093-2, Paper and board Testing of cores Part 2: Conditioning of test samples 3 ForewordISO (the Inter

11、national Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has

12、been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical st

13、andardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accor

14、dance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details

15、 of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endor

16、sement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee respons

17、ible for this document is ISO/TC 6, Paper, board and pulps.This third edition cancels and replaces the second edition (ISO 11093-5:2009), of which it constitutes a minor revision. It also incorporates the Technical Corrigendum ISO 11093-5:2009/Cor.1:2010.ISO 11093 consists of the following parts, un

18、der the general title Paper and board Testing of cores: Part 1: Sampling Part 2: Conditioning of test samples Part 3: Determination of moisture content using the oven drying method Part 4: Measurement of dimensions Part 5: Determination of characteristics of concentric rotation Part 6: Determination

19、 of bending strength by the three-point method Part 7: Determination of flexural modulus by the three-point method Part 8: Determination of natural frequency and flexural modulus by experimental modal analysis Part 9: Determination of flat crush resistanceDIN ISO 11093-5:2017-05 4 1 ScopeThis part o

20、f ISO 11093 specifies a method for determining the characteristics of concentric rotation of cylindrical board cores which meet the following criteria: minimum wall thickness: 5 mm; minimum external diameter: 60 mm; maximum sample length: 3 200 mm.2 Normative referencesThe following documents, in wh

21、ole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 110931, Paper and board Testing of

22、 cores Part 1: SamplingISO 110932, Paper and board Testing of cores Part 2: Conditioning of test samples3 Principles3.1 Determination of roundness deviation (fR) by three-point measurementMeasurement between three points in a plane perpendicular to the core axis where two points are fixed in predete

23、rmined positions and the third moves in the direction of the measurement.3.2 Determination of the straightness deviation (fS) by five-point measurementMeasurement between five points in planes perpendicular to the core axis where four measuring points are fixed in pairs in predetermined positions in

24、 two planes perpendicular to the core axis, and the fifth in a central plane perpendicular to the core axis moves in the direction of the measurement.4 ApparatusThe apparatus, shown in Figure 1, consists of two supports (2), a rack (1), and two measuring heads (4 and 5). Each support consists of two

25、 free rotating support rollers mounted side by side (3) where the distance between the two can be adjusted. The diameter of each roller shall be (85 1) mm and the width shall be (19 1) mm. For example, a 6209 roller bearing can be used.Each measuring head consists of a flat foot with a diameter of 1

26、0 mm, a rod which transmits the vertical movement of the foot to a dial gauge and a dial gauge graduated in 0,01 mm, accurate to at least 0,005 mm. The load exerted by each measuring foot on the test piece is approximately 1,2 N. One of the measuring heads (4) is fixed directly above the mid-point b

27、etween one pair of support rollers. The other measuring head (5) is moveable parallel to the rack.Paper and board Testing of cores Part 5: Determination of characteristics of concentric rotation DIN ISO 11093-5:2017-05 5 123456Key1 rack2 supports3 support rollers4 measuring head5 measuring head, mov

28、eable6 test pieceFigure 1 Schematic representation of the apparatus5 Preparation of test pieces5.1 SamplingSampling shall be carried out in accordance with ISO 11093-1.5.2 Test piecesFor cores less than 3 200 mm long, the complete undamaged core shall be tested.For cores more than 3 200 mm long, a t

29、est piece from 1 200 mm to 3 200 mm long shall be cut. If there is an obvious difference in warpage between various positions of the long core, the test piece shall be taken from where the warpage is greatest.5.3 Conditioning of test piecesThe test pieces shall be conditioned in accordance with ISO

30、11093-2.DIN ISO 11093-5:2017-05 6 6 Measuring procedure6.1 GeneralMeasuring shall be carried out in a standard atmosphere identical to that used for the conditioning (see 5.3). The measuring heads shall not produce any measurable deformation of the test piece during measuring.6.2 Positioning of the

31、supportAdjust the distance between the two support rollers within each pair so that the tangents to the lines of the support of the core form an angle of 120 5. Adjust the distance between the inner faces of the two pairs of support rollers to the core length less (200 10) mm. This is the test lengt

32、h. Position the core centrally on the support rollers.6.3 Measuring of roundness deviationPlace the foot of the fixed measuring head in contact with the core so that it is centrally located with respect to the core axis and the line between the support-roller pair to an accuracy of 1 mm. Rotate the

33、core through 360 and record the highest and lowest readings of the gauge to an accuracy of 0,01 mm. The difference between the two readings is the individual value for the roundness deviation ( fR), expressed in millimetres.6.4 Measuring of straightness deviation6.4.1 Straightness deviationPlace the

34、 foot of the moveable measuring head in contact with the core so that it is centrally located with respect to the core axis at a point half-way between the two support-roller pairs. The measuring head placed at the half-way point is located with an accuracy of 1 mm. Rotate the core through 360 and r

35、ecord the highest and lowest readings of the gauge to an accuracy of 0,01 mm. Record the difference between the two readings. The straightness deviation ( fS) is half of this measured difference (x), determined with an accuracy of 0,01 mm, as given in Formula (1):fxS=2(1)wherefSis the straightness d

36、eviation, in mm;x is the measured difference, in mm.6.4.2 Precision of the measurement systemProvided that the rack has the stiffness needed, the precision of the measurement system is sufficient for cores which have a straightness deviation 0,3 mm/m.DIN ISO 11093-5:2017-05 7 To obtain comparable va

37、lues for paper cores of different (support) lengths, the following conversion to millimetres per metre (mm/m), as given in Formula (2), shall be made:fflSS=1000(2)wherefSis the straightness deviation, in mm/m;fSis the straightness deviation, in mm see Formula (1) in 6.4.1;l is the distance between s

38、upports (inner measurement), in mm.7 CalculationCalculate the mean and standard deviation for the roundness deviation and straightness deviation to the nearest 0,01 mm.8 Test reportThe test report shall include the following information:a) reference to this part of ISO 11093, i.e. ISO 110935;b) type

39、 and designation of the cores tested;c) place and date of sampling;d) place and date of test;e) number of test pieces;f) core length;g) test length;h) mean and standard deviation of the roundness deviation ( fR);i) mean and standard deviation of the straightness deviation ( fS);j) date and signature;k) any deviation from this part of ISO 11093 that might have affected the results.DIN ISO 11093-5:2017-05 8