DIN EN ISO 21003-1-2008 Multilayer piping systems for hot and cold water installations inside buildings - Part 1 General (ISO 21003-1 2008) English version of DIN EN ISO 21003-1 20.pdf

《DIN EN ISO 21003-1-2008 Multilayer piping systems for hot and cold water installations inside buildings - Part 1 General (ISO 21003-1 2008) English version of DIN EN ISO 21003-1 20.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 21003-1-2008 Multilayer piping systems for hot and cold water installations inside buildings - Part 1 General (ISO 21003-1 2008) English version of DIN EN ISO 21003-1 20.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、November 2008DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.140.60!$Rx$“147850

2、1www.din.deDDIN EN ISO 21003-1Multilayer piping systems for hot and cold water installations insidebuildings Part 1: General (ISO 21003-1:2008)English version of DIN EN ISO 21003-1:2008-11Mehrschichtverbund-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallationinnerhalb von Gebuden Teil 1: Allg

3、emeines (ISO 21003-1:2008)Englische Fassung DIN EN ISO 21003-1:2008-11www.beuth.deDocument comprises 18 pagesDIN EN ISO 21003-1:2008-11 2 National foreword This standard has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, Subcommitte

4、e SC 2 “Plastics pipes and fittings for water supplies” (Secretariat: SNV, Switzerland) in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body involved in its preparation was the Normenausschuss

5、Wasserwesen (Water Practice Standards Committee), Technical Committee NA 119-04-06-06 GUA Kunststoffrohre in der Trink-wasserversorgung; Mehrschichtrohrsysteme. The International Standards referred to in clause 2 of this document have been published as the correspond-ing DIN EN or DIN EN ISO Standar

6、ds with the same number: ISO 472 DIN EN ISO 472 ISO 1043-1 DIN EN ISO 1043-1 ISO 15874-1 DIN EN ISO 15874-1 ISO 15874-2 DIN EN ISO 15874-2 ISO 15874-3 DIN EN ISO 15874-3 ISO 15874-5 DIN EN ISO 15874-5 ISO 15875-1 DIN EN ISO 15875-1 ISO 15875-2 DIN EN ISO 15875-2 ISO 15875-3 DIN EN ISO 15875-3 ISO 15

7、875-5 DIN EN ISO 15875-5 ISO 15876-1 DIN EN ISO 15876-1 ISO 15876-2 DIN EN ISO 15876-2 ISO 15876-3 DIN EN ISO 15876-3 ISO 15876-5 DIN EN ISO 15876-5 ISO 15877-1 DIN EN ISO 15877-1 ISO 15877-2 DIN EN ISO 15877-2 ISO 15877-3 DIN EN ISO 15877-3 ISO 15877-5 DIN EN ISO 15877-5 ISO 21003-2 DIN EN ISO 2100

8、3-2 ISO 21003-3 DIN EN ISO 21003-3 ISO 21003-5 DIN EN ISO 21003-5 ISO/TS 21003-7 DIN ISO/TS 21003-7 DIN EN ISO 21003-1:2008-11 3 National Annex NA (informative) Bibliography DIN EN ISO 472, Plastics Vocabulary DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their

9、 special characteristics DIN EN ISO 15874-1, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 1: General DIN EN ISO 15874-2, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 2: Pipes DIN EN ISO 15874-3, Plastics piping systems f

10、or hot and cold water installations Polypropylene (PP) Part 3: Fittings DIN EN ISO 15874-5, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 5: Fitness for purpose of the system DIN EN ISO 15875-1, Plastics piping systems for hot and cold water installations Cross

11、linked polyethylene (PE-X) Part 1: General DIN EN ISO 15875-2, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 2: Pipes DIN EN ISO 15875-3, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 3: Fittings

12、DIN EN ISO 15875-5, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 5: Fitness for purpose of the system DIN EN ISO 15876-1, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 1: General DIN EN ISO 15876-2, Plastics p

13、iping systems for hot and cold water installations Polybutylene (PB) Part 2: Pipes DIN EN ISO 15876-3, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 3: Fittings DIN EN ISO 15876-5, Plastics piping systems for hot and cold water installations Polybutylene (PB) Pa

14、rt 5: Fitness for purpose of the system DIN EN ISO 15877-1, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 1: General DIN EN ISO 15877-2, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C)

15、Part 2: Pipes DIN EN ISO 15877-3, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings DIN EN ISO 21003-1:2008-11 4 DIN EN ISO 15877-5, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC

16、-C) Part 5: Fitness for purpose of the system DIN EN ISO 21003-2, Multilayer piping systems for hot and cold water installations inside buildings Part 2: Pipes DIN EN ISO 21003-3, Multilayer piping systems for hot and cold water installations inside buildings Part 3: Fittings DIN EN ISO 21003-5, Mul

17、tilayer piping systems for hot and cold water installations inside buildings Part 5: Fitness for purpose of the system DIN ISO/TS 21003-7, Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity EUROPEAN STANDARDNORME EUROPENN

18、EEUROPISCHE NORMEN ISO 21003-1July 2008ICS 23.040.01; 91.140.60English VersionMultilayer piping systems for hot and cold water installationsinside buildings - Part 1: General (ISO 21003-1:2008)Systmes de canalisations multicouches pour installationsdeau chaude et froide lintrieur des btiments - Part

19、ie 1:Gnralits (ISO 21003-1:2008)Mehrschichtverbund-Rohrleitungssysteme fr die Warm-und Kaltwasserinstallation innerhalb von Gebuden - Teil 1:Allgemeines (ISO 21003-1:2008)This European Standard was approved by CEN on 15 June 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulati

20、ons which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This Europe

21、an Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the nationa

22、l standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Unite

23、d Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 21003-1:2008:

24、 E2 EN ISO 21003-1:2008 (E) DIN EN ISO 21003-1:2008-11 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 6 3 Terms and definitions .7 3.1 Definitions related to construction 7 3.2 Definitions related to geometry8 3.3 Definitions related to service conditions 8 3.4 Definitions

25、related to materials 9 3.5 Definitions related to material characteristics9 3.6 Definitions related to temperature .9 4 Symbols and abbreviated terms . 10 4.1 Symbols . 10 4.2 Abbreviated terms 11 5 Classification of service conditions . 11 6 Material 12 6.1 General. 12 6.2 Influence on water intend

26、ed for human consumption 12 Annex A (normative) List of reference product standards 13 Bibliography. 14 3 Foreword This document (EN ISO 21003-1:2008) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“ in collaboration with Technical

27、 Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national

28、 standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been pr

29、epared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this document. According to the CEN

30、/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L

31、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 21003-1:2008 has been approved by CEN as EN ISO 21003-1:2008 without any modification. EN ISO 21003-1:2008 (E) DIN EN ISO 21003-

32、1:2008-11 Introduction The system standard of which this is Part 1 specifies the requirements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside buildings. In respect of potentially adverse effects on the quality of water i

33、ntended for human consumption caused by the products covered by ISO 21003: no information is provided as to whether the products may be used without restriction in any of the member states of the EU or EFTA; it should be noted that, while awaiting the adoption of verifiable European criteria, existi

34、ng national regulations concerning the use and/or the characteristics of these products remain in force. Requirements and test methods for components of the piping system are specified in ISO 21003-2 and ISO 21003-3. Characteristics relating to fitness for purpose (mainly for joints) are covered in

35、ISO 21003-5. ISO/TS 21003-7 gives guidance on the assessment of conformity. This part of ISO 21003 specifies the general aspects of multilayer piping systems. For ancillary equipment, separate standards can apply. Guidance on installation of plastics piping systems made from various materials intend

36、ed to be used for hot and cold water installations is given in ENV 12108. Other system standards which, at the date of publication of this part of ISO 21003, had been published for plastics piping systems used for the same application are listed in Annex A. 4 EN ISO 21003-1:2008 (E) DIN EN ISO 21003

37、-1:2008-11 1 Scope This part of ISO 21003 specifies the general aspects of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water whether or not the water is intended for human consumption (domestic systems) or heating systems

38、under specified design pressures and temperatures appropriate to the class of application (see Table 1). ISO 21003 is a reference product standard (see 3.4.3). It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics mat

39、erials intended to be used for hot and cold water installations. This part of ISO 21003 is intended for use only in conjunction with all the other parts of ISO 21003. ISO 21003 applies only to multilayer pipes with their inner layer made of plastics. It covers a range of service conditions (applicat

40、ion classes) and design pressures. It is not applicable for values of design temperature, TD, maximum design temperature, Tmax, and malfunction temperature, Tmal, in excess of those in Table 1. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from thes

41、e aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. The polymeric materials used for the stress-designed layers are the following: polybutylene (PB), polyethylene of raised temperature resistance (PE-RT), crosslinked

42、 polyethylene (PE-X), polypropylene (PP) and chlorinated poly(vinyl chloride) (PVC-C). The PE-X used shall be fully crosslinked and shall comply with the requirements of the relevant reference product standard (ISO 15875). NOTE 2 For the purposes of ISO 21003, crosslinked polyethylene (PE-X) as well

43、 as adhesives are considered as thermoplastic materials. Solid-wall pipes with thin outer layers (applied as protection layers or barrier layers, for instance) are not covered by ISO 21003 but are specified in the Amendments to ISO 15874-2, ISO 15875-2 and ISO 15876-2. The total thickness of such ou

44、ter layers, including the thickness of the adhesives used, shall be u 0,4 mm. 5 EN ISO 21003-1:2008 (E) DIN EN ISO 21003-1:2008-11 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. F

45、or undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbers ISO 472, Plastics Vocabulary ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics ISO 1

46、5874-1, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 1: General ISO 15874-2, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 2: Pipes ISO 15874-3, Plastics piping systems for hot and cold water installations Polypropylene (

47、PP) Part 3: Fittings ISO 15874-5, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 5: Fitness for purpose of the system ISO 15875-1, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 1: General ISO 15875-2, Plastics

48、piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 2: Pipes ISO 15875-3, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 3: Fittings ISO 15875-5, Plastics piping systems for hot and cold water installations Cross

49、linked polyethylene (PE-X) Part 5: Fitness for purpose of the system ISO 15876-1, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 1: General ISO 15876-2, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 2: Pipes ISO 15876-3, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 3: Fittings ISO 15876-5, Plasti