DIN EN ISO 20848-2-2008 Packaging - Plastics drums - Part 2 Non-removable head (tight head) drums with a nominal capacity of 208 2 l and 220 l (ISO 20848-2 2006) German version EN .pdf

《DIN EN ISO 20848-2-2008 Packaging - Plastics drums - Part 2 Non-removable head (tight head) drums with a nominal capacity of 208 2 l and 220 l (ISO 20848-2 2006) German version EN .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 20848-2-2008 Packaging - Plastics drums - Part 2 Non-removable head (tight head) drums with a nominal capacity of 208 2 l and 220 l (ISO 20848-2 2006) German version EN .pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、September 2008DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55.140!$QfC“1466732w

2、ww.din.deDDIN EN ISO 20848-2Packaging Plastics drums Part 2: Non-removable head (tight head) drums with a nominal capacityof 208,2 l and 220 l (ISO 20848-2:2006)English version of DIN EN ISO 20848-2:2008-09Verpackung Kunststofffsser Teil 2: Spundfsser mit einem Nennvolumen von 208,2 l und 220 l (ISO

3、 20848-2:2006)Englische Fassung DIN EN ISO 20848-2:2008-09Partially supersedesDIN EN 12707:2000-03www.beuth.deDocument comprises 18 pagesDIN EN ISO 20848-2:2008-09 2 National foreword This standard has been prepared by Technical Committee ISO/TC 122 “Packaging” with TSE (Turkey) holding the secretar

4、iat. The secretariat is currently held by JISC (Japan) and ISIRI (Iran). This standard has been published in accordance with a decision taken by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France), Subcommittee SC 5 “Primary packaging and transport packaging” (Secretariat: BSI, U

5、nited Kingdom) to adopt, without alteration, International Standard ISO 20848-2:2006 as European Standard EN ISO 20848-2:2008. The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Technical Committee NA 115-02-03 AA Spund-

6、und Deckelfsser. DIN EN ISO 20848 consists of the following parts, under the general title Packaging Plastics drums: Part 1: Removable head (open head) drums with a nominal capacity of 113,6 l to 220 l Part 2: Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l Part 3:

7、 Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l The DIN Standard corresponding to the International Standard referred to in this document are as follows: ISO 16104 DIN EN ISO 16104 ISO 20848-3 DIN EN ISO 20848-3 Amendments This standard differs from DIN EN 1

8、2707:2000-03 as follows: a) The specifications for drums with a nominal capacity of 220 l have been taken from DIN EN 12707:2000-03, which will be revised as regards the remaining nominal capacities of 210 l and 225 l. b) The standard has been editorially revised. Previous editions DIN 6131-3: 1985-

9、07, 1989-08 DIN EN 12707: 2000-03 National Annex NA (informative) Bibliography DIN EN ISO 16104, Packaging Transport packaging for dangerous goods Tests methods DIN EN ISO 20848-3, Packaging Plastics drums Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220

10、 l EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 20848-2 June 2008 ICS 55.140 English Version Packaging - Plastics drums - Part 2: Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l (ISO 20848-2:2006) Emballages - Fts en matire plastique - Partie 2: Fts ouv

11、erture non amovible (ouverture partielle) dune capacit nominale de 208,2 l et 220 l (ISO 20848-2:2006) Verpackung - Kunststofffsser - Teil 2: Spundfsser mit einem Nennvolumen von 208,2 l und 220 l (ISO 20848-2:2006) This European Standard was approved by CEN on 16 May 2008. CEN members are bound to

12、comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Man

13、agement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as

14、 the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slov

15、akia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwi

16、de for CEN national Members. Ref. No. EN ISO 20848-2:2008: EContents Page 2 EN ISO 20848-2:2008 (E) DIN EN ISO 20848-2:2008-09 Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Requirements.6 4.1 Dimensions.6 4.2 Drum mass .7 4.3 Material identification symbol

17、 7 4.4 Closures8 4.5 Materials .8 4.6 Handling8 4.7 Stacking8 4.8 Draining 9 4.9 Finish 9 5 Designation 9 Annex A (normative) Capacity measurement method for non-removable head (tight head) plastics drums. 10 Annex B (normative) Draining test method for non-removable head (tight head) plastics drums

18、 . 12 Annex C (normative) International material code symbols . 14 Bibliography. 16 Foreword 3 EN ISO 20848-2:2008 (E) DIN EN ISO 20848-2:2008-09 The text of ISO 20848-2:2006 has been prepared by Technical Committee ISO/TC 122 “Packaging” of the International Organization for Standardization (ISO) a

19、nd has been taken over as EN ISO 20848-2:2008 by Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2008

20、, and conflicting national standards shall be withdrawn at the latest by December 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights

21、. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy

22、, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 20848-2:2006 has been approved by CEN as a EN ISO 20848-2:2008 without any modification. Introduction Thro

23、ughout the world, a large number of plastics drum types with different dimensions and characteristics are being used. The differences in location of the minimum filling opening and outer dimensions result in differences in filling, handling and transportation. ISO 20848 specifies the characteristics

24、 and dimensions of plastics drums which are of importance for the worldwide safe handling and transport of substances and for the continued reuse of the drums during their life cycle. Detailed performance requirements and the related test methods are not included as they depend upon the specific app

25、lication. Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory requirements which govern the transport of those goods in the countries concerned, including capseals/overseals fitted in accordance with the certificate. Depending upon the m

26、ode of transport, this means meeting the requirements of: UN (United Nations) Recommendations on the Transport of Dangerous Goods, ICAO (International Civil Aviation Organization) Technical Instructions for the Safe Transport of Dangerous Goods by Air, IMO (International Maritime Organization) Inter

27、national Maritime Dangerous Goods (IMDG) Code. This involves the certification and marking of the drums according to the regulations. 4 DIN EN ISO 20848-2:2008-09 EN ISO 20848-2:2008 (E) 1 Scope This part of ISO 20848 specifies the characteristics and dimensions of non-removable head (tight head) pl

28、astics drums with a nominal capacity of 208,2 l and 220 l. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (in

29、cluding any amendments) applies. ISO 20848-3, Packaging Plastics drums Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 non-removable head (tight

30、head) drum TH flat-ended or convex-ended circular cross-section packaging with openings for filling and emptying in the head not exceeding 70 mm in diameter 3.2 nominal capacity NC capacity in litres which, by convention, is used to represent a class of drums of similar brimful capacities 3.3 brimfu

31、l capacity BC volume of water in litres held by the drum when filled through the filling orifice to the point of overflowing NOTE Annex A specifies the method for measuring brimful capacity. 3.4 total capacity TC volume of water in litres held by the drum when filled completely, i.e. following the r

32、emoval of any air trapped in the drum NOTE Annex A specifies the method for measuring total capacity. 5 EN ISO 20848-2:2008 (E) DIN EN ISO 20848-2:2008-09 3.5 overall height, hoheight of the finished drum from the base to the highest point NOTE See Figure 1. 3.6 overall diameter, domaximum diameter

33、of the drum, where relevant NOTE See Figure 1. 3.7 bung housing position, pbdistance from the centre of the bung housing to the outside of the drum body 50 mm vertically below the top edge of the top handling ring NOTE See Figure 1. 3.8 drum mass mass of the empty drum including all closures 4 Requi

34、rements 4.1 Dimensions The dimensions and tolerances of the drum shall be as listed in Table 1 and as shown in Figure 1. The measurements shall be conducted at ambient conditions but shall not be made within 48 h of manufacture. NOTE Apart from the dimensions specified, there are no restrictions on

35、drum shape. Table 1 Dimensions of non-removable (tight head) drums with a nominal capacity of 208,2 l and 220 l (55 US gal and 58,1 US gal) Nominal capacity, NC Brimful capacity, BC Overall diameter, doBung housing position, pbOverall height,hol (US gal) l (US gal) mm mm mm 208,2 (55) 216,5 50+(57,2

36、 1, 3 20+) 595 57+84 2 890 7 220 (58,1) 222 32+(58,6 0, 80, 5+) 581 5 72 2 935 5 NOTE 1 The bung housing position defined in this table only applies to that housing used for filling. NOTE 2 Dimensions do, pband hoare applicable to empty drums. NOTE 3 1 US gal = 3,785 l. 6 DIN EN ISO 20848-2:2008-09

37、EN ISO 20848-2:2008 (E) Dimensions in millimetres Key pbbung housing position dooverall diameter hooverall height The complete closure (plug and capseals/overseals) should not protrude above the overall height ho. NOTE Four possible designs are shown. Figure 1 Non-removable head (tight head) drum 4.

38、2 Drum mass The mass tolerance of the drum shall be 3 %. NOTE The defined mass should be agreed between the purchaser and the supplier. 4.3 Material identification symbol The drum shall be permanently marked with the relevant material identification symbol, i.e. the symbol identifying the material f

39、rom which the drum is made, as shown in Annex C. 7 EN ISO 20848-2:2008 (E) DIN EN ISO 20848-2:2008-09 4.4 Closures There shall be two closures in accordance with ISO 20848-3. When fitted, the closures shall not protrude above the overall height of the drum. The preferred options are identified in Ta

40、ble 2. The closure systems shall incorporate a facility for providing tamper evidence. For the purpose of transport and storage, the filled drum should be closed, using the appropriate tooling, to the manufacturers recommended closure torque for each type of gasket. NOTE 1 For closures in drums inte

41、nded for dangerous goods, the tolerance on the torque figures are specified in ISO 16104. NOTE 2 After tightening of plugs, torques will reduce over time. In particular, plastics components are subject to stress relaxation resulting in a reduced torque. NOTE 3 Torque figures supplied by the manufact

42、urer are valid for the tightening of plugs in a clockwise direction. The measurement of torques on releasing plugs, i.e. in an anticlockwise direction, are different. Table 2 Preferred closure system combinations Draining side Second side BCS G2 11,5 BCS 70 6 BCS G2 11,5 BCS 56 4 BCS G2 11,5 BCS G2

43、5 4.5 Materials The drum shall be manufactured from high-density polyethylene or another suitable plastics material, or a combination thereof. Suitable non-plastics material may be used in conjunction with the plastics material. NOTE Suitable additives may be included provided the specifications are

44、 identified. 4.6 Handling Provision shall be made to enable the drum to be mechanically handled using one or two permanently fixed handling rings. The construction of the handling rings shall be adequate for normal static and dynamic handling of filled drums. 4.7 Stacking The drum shall be capable o

45、f being stacked with or without pallets, according to the manufacturers recommendations. 8 DIN EN ISO 20848-2:2008-09 EN ISO 20848-2:2008 (E) 4.8 Draining 4.8.1 The drum shall be designed so as to minimize the residual volume of liquid left in the drum after drainage. The residue shall be not more t

46、han 100 ml when tested according to B.3. 4.8.2 The residue obtained when the drum is tested according to B.4 is more dependent on the area and condition of the internal surface of the drum than when the drum is tested according to B.3 and, therefore, may be in excess of that obtained according to B.

47、3. NOTE The maximum permitted figure should be agreed between the purchaser and the supplier. 4.9 Finish The external surface finish shall be suitable for the attachment of labels. NOTE 1 The nature of the internal and external finish should be agreed between the purchaser and the supplier. The drum

48、 body should be blue in colour. The use of any other colour and any durable marking should be agreed between the purchaser and the supplier. 5 Designation A non-removable head (tight head) drum (TH) manufactured in accordance with this part of ISO 20848 with a nominal capacity of 220 l shall be so d

49、esignated, e.g. Plastics drum TH ISO 20848-2 NC - 220 l 9 EN ISO 20848-2:2008 (E) DIN EN ISO 20848-2:2008-09 Annex A (normative) Capacity measurement method for non-removable head (tight head) plastics drums A.1 Principle The capacity is determined by a gravimetric method, i.e. by the measurement of the mass of water in the filled drum and its conversion to a capacity. A correction factor can be applied according to Table A.1, but only if the weighing scale used is of a higher precision than the co