DIN EN ISO 20028-1-2017 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 20028-1 2017) German .pdf

《DIN EN ISO 20028-1-2017 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 20028-1 2017) German .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 20028-1-2017 Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 20028-1 2017) German .pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、July 2017 English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.080.20!%guN“2688243www.din.deDIN

2、 EN ISO 20028-1Plastics Thermoplastic polyester (TP) moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO 200281:2017);English version EN ISO 200281:2017,English translation of DIN EN ISO 20028-1:2017-07Kunststoffe Thermoplastische Polyester (TP)Werkstoffe Te

3、il 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 200281:2017);Englische Fassung EN ISO 200281:2017,Englische bersetzung von DIN EN ISO 20028-1:2017-07Plastiques Matriaux polyesters thermoplastiques (TP) pour moulage et extrusion Partie 1: Systme de dsignation et base de spcification (ISO 2

4、00281:2017);Version anglaise EN ISO 200281:2017,Traduction anglaise de DIN EN ISO 20028-1:2017-07SupersedesDIN EN ISO 77921:201303www.beuth.deDocument comprises 22 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.06.17 DIN EN IS

5、O 20028-1:2017-07 2 A comma is used as the decimal marker. National foreword This document (EN ISO 20028-1:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible German body invo

6、lved in its preparation was DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-02-10 AA “Thermoplastic materials”. DIN EN ISO 20028, Plastics Thermoplastic polyester (TP) moulding and extrusion materials consists of the following parts: Part 1: Designation s

7、ystem and basis for specifications Part 2: Preparation of test specimens and determination of properties The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1043-1 DIN EN ISO 1043-1 ISO 1043-2 DIN EN ISO 1043-2 ISO 1628-5 DIN EN ISO 1628-5

8、ISO 16396-1 DIN EN ISO 16396-1 ISO 20028-2 DIN EN ISO 20028-2 Amendments This standard differs from DIN EN ISO 7792-1:2013-03 as follows: a) the number of the standard has been changed to DIN EN ISO 20028-1; b) an introduction has been included; c) the Scope has been adapted due to the new designati

9、on system; d) Clause 3 “Designation system” has been adapted to the new designation system and is now Clause 4; e) Clause 4 “Examples of designations” has been adapted to the new designation system and is now Clause 5; f) normative references have been updated; g) the standard has been editorially r

10、evised. Previous editions DIN 16779-1: 1988-01 DIN EN ISO 7792-1: 2004-10, 2013-03 DIN EN ISO 20028-1:2017-07 3 National Annex NA (informative) Bibliography DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics DIN EN ISO 1043-2, Plastics

11、Symbols and abbreviated terms Part 2: Fillers and reinforcing materials DIN EN ISO 1628-5, Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 5: Thermoplastic polyester (TP) homopolymers and copolymers DIN EN ISO 16396-1, Plastics Polyamide (PA) m

12、oulding and extrusion materials Part 1: Designation system, marking of products and basis for specifications DIN EN ISO 20028-2, Plastics Thermoplastic polyester (TP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties DIN EN ISO 20028-1:2017-07 4 T

13、his page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 20028-1 March 2017 ICS 83.080.20 Supersedes EN ISO 7792-1:2012 English Version Plastics Thermoplastic polyester (TP) moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO

14、20028-1:2017) Plastiques Matriaux polyesters thermoplastiques (TP) pour moulage et extrusion Partie 1: Systme de dsignation et base de spcification (ISO 20028-1:2017) Kunststoffe Thermoplastische Polyester (TP)-Werkstoffe Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 20028-1:2017) Thi

15、s European Standard was approved by CEN on 3 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere

16、nces concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN

17、member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

18、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION E

19、UROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 20028-1:2017 E EN ISO 20028-1:2017 (E) 2 Contents Page Foreword 4 Introduction

20、5 1 Scope 6 2 Normative references 6 3 Terms and definitions . 7 4 Designation system 7 4.1 General 7 4.2 Data block 1 . 7 4.3 Data block 2 . 8 4.4 Data block 3 . 9 4.5 Data block 4 10 4.5.1 General . 10 4.5.2 Viscosity number 10 4.5.3 Tensile modulus of elasticity . 11 4.6 Data block 5 12 5 Example

21、s of designations 12 5.1 Designation only . 12 5.2 Designation transformed into a specification . 14 Annex A (normative) Designation of thermoplastic polyesters . 15 Bibliography . 18 DIN EN ISO 20028-1:2017-07 European foreword . 3 EN ISO 20028-1:2017 (E) 3 European foreword This document (EN ISO 2

22、0028-1:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or b

23、y endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsibl

24、e for identifying any or all such patent rights. This document supersedes EN ISO 7792-1:2012. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

25、 Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the U

26、nited Kingdom. Endorsement notice The text of ISO 20028-1:2017 has been approved by CEN as EN ISO 20028-1:2017 without any modification. DIN EN ISO 20028-1:2017-07 ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodi

27、es). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

28、non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are desc

29、ribed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is draw

30、n to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on t

31、he ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessm

32、ent, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic

33、 materials.This first edition of ISO 20028-1 cancels and replaces ISO 7792-1:2012, which has been technically revised to introduce a new designation system.The revised designation system is published under a new ISO number, as many existing documents refer to ISO 7792-1. If the existing ISO 7792-1 w

34、ould be replaced by the new designation system, these documents would refer to the incorrect designation system.In order to give users time to switch from ISO 7792-1 to ISO 20028-1, any designation system according to ISO 7792-1 is to be phased out in 5 to 10 years.A list of all parts in the ISO 200

35、28 series can be found on the ISO website.4 EN ISO 20028-1:2017 (E) DIN EN ISO 20028-1:2017-07 IntroductionISO 7792-1 is complex and does not fit with daily practice anymore. In practice, ISO 1043 and ISO 11469 are, in combination, “improperly” being used as a designation system for, for example, ma

36、rking. The aim of this revision is to simplify the data block system and to connect more to ISO 1043 and ISO 11469, where the first two blocks are used for generic identification and marking of products.5 EN ISO 20028-1:2017 (E) DIN EN ISO 20028-1:2017-07 1 ScopeThis document establishes a system of

37、 designation for thermoplastic polyester (TP) material, which can be used as the basis for specifications. It covers polyester homopolymers for moulding and extrusion based on poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT), poly(cyclohexylenedimethylene terephthalate) (PCT),

38、poly(ethylene naphthalate) (PEN), poly(butylene naphthalates) (PBN) and other TP-types and copolyesters of various compositions for moulding and extrusion.The types of thermoplastic polyester are differentiated from each other by a classification system based on appropriate levels of the designatory

39、 properties:a) viscosity number;b) tensile modulus of elasticity;and on information about the intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.This designation system is applicable to thermoplastic polyester homopolymers

40、and copolymers. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, fillers and other additives. This document does not apply to the saturated polyester/ester and polyether/ester thermoplastic elastomers covered by ISO 20029.I

41、t is not intended to imply that materials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on processing conditions which can be required to specify a material. If such additional properties are required, the

42、y are intended to be determined in accordance with the test methods specified in ISO 20028-2, if suitable.In order to designate a thermoplastic polyester material to meet particular specifications, the requirements are to be given in data block 5 (see 3.1).2 Normative referencesThe following documen

43、ts are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1043-1, Plastic

44、s Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materialsISO 1628-5, Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 5: T

45、hermoplastic polyester (TP) homopolymers and copolymersISO 20028-2, Plastics Thermoplastic polyester (TP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties6 EN ISO 20028-1:2017 (E) DIN EN ISO 20028-1:2017-07 ASTM D5927, Standard Classification Sys

46、tem for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following add

47、resses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 Designation system4.1 GeneralThe designation system for thermoplastics is based on the following standardized pattern.DesignationDescription Identity bl

48、ockBlock (optional)International StandardIndividual item blocknumber blockData block 1 Data block 2 Data block 3 Data block 4 Data block 5The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an ind

49、ividual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information. Data block 1: Identification of the plastic by its symbol PET, PBT, PCT, PEN, PBN or TP for all such polyesters and copolyesters in general, in accordance with ISO 1043-1 (see 4.2). Data block 2: Position 1: Fillers or reinforcing materials and their nominal cont