DIN EN ISO 8765-2011 Hexagon head bolts with metric fine pitch thread - Product grades A and B (ISO 8765 2011) German version EN ISO 8765 2011《公制细牙螺纹的六角头螺栓 产品等级A和B(ISO 8765-2011) 德.pdf

《DIN EN ISO 8765-2011 Hexagon head bolts with metric fine pitch thread - Product grades A and B (ISO 8765 2011) German version EN ISO 8765 2011《公制细牙螺纹的六角头螺栓 产品等级A和B(ISO 8765-2011) 德.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 8765-2011 Hexagon head bolts with metric fine pitch thread - Product grades A and B (ISO 8765 2011) German version EN ISO 8765 2011《公制细牙螺纹的六角头螺栓 产品等级A和B(ISO 8765-2011) 德.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、June 2011 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、1.060.10!$s,b“1800963www.din.deDDIN EN ISO 8765Hexagon head bolts with metric fine pitch thread Product grades A and B (ISO 8765:2011)English translation of DIN EN ISO 8765:2011-06Sechskantschrauben mit Schaft und metrischem Feingewinde Produktklassen A und B (ISO 8765:2011)Englische bersetzung von

3、DIN EN ISO 8765:2011-06Vis tte hexagonale filetage mtrique pas fin partiellement filetes Grades A et B (ISO 8765:2011)Traduction anglaise de DIN EN ISO 8765:2011-06SupersedesDIN EN ISO 8765:2001-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered

4、authoritative.1906.11 DIN EN ISO 8765:2011-06 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The resp

5、onsible German body involved in its preparation was the Normenausschuss Mechanische Verbin-dungselemente (Fasteners Standards Committee), Working Committee NA 067-00-02 AA Verbindungs-elemente mit metrischem Auengewinde. The DIN 4000-160 tabular layout of article characteristics shall apply to screw

6、s covered in this standard. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 225 DIN EN ISO 225 ISO 261 DIN ISO 261 ISO 724 DIN ISO 724 ISO 898-1 DIN EN ISO 898-1 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 350

7、6-1 ISO 4042 DIN EN ISO 4042 ISO 4753 DIN EN ISO 4753 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 Amendments This standard differs from DIN EN ISO 8765:2001-03 as follows: a) normative references are now undated; b) th

8、e standard has been editorially revised and normative references have been updated; c) Annex ZA has been deleted. Previous editions DIN Kr 551: 1935-09, 1936-11 DIN 960: 1942-04, 1953-02, 1963-03, 1967-11, 1970-11, 1983-12, 1990-01 DIN ISO 8765: 1990-01 DIN EN 28765: 1992-02 DIN EN ISO 8765: 2001-03

9、 -1DIN EN ISO 8765:2011-06 3 National Annex NA (informative) Bibliography DIN 4000-160, Tabular layout of product properties Part 160: Fasteners with external thread DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general requirements DIN EN 28839, Mechanical pro

10、perties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified

11、property classes Coarse thread and fine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4753, Fasteners

12、 Ends of parts with external ISO metric thread DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN ISO 261, ISO general purpose metric screw threads General plan D

13、IN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN EN ISO 8765:2011-06 4 This page is intentional

14、ly blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8765 March 2011 ICS 21.060.10 Supersedes EN ISO 8765:2000English Version Hexagon head bolts with metric fine pitch thread - Product grades A and B (ISO 8765:2011) Vis tte hexagonale filetage mtrique pas fin partiellement filetes - Gra

15、des A et B (ISO 8765:2011) Sechskantschrauben mit Schaft und metrischem Feingewinde - Produktklassen A und B (ISO 8765:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giv

16、ing this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three off

17、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies o

18、f Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom

19、. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8765:2011: EConten

20、ts DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) 2 Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Dimensions.6 4 Specifications and reference International Standards 13 5 Designation 13 Bibliography 14 Foreword This document (EN ISO 8765:2011) has been prepared by Technical Commi

21、ttee ISO/TC 2 Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, a

22、nd conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.

23、This document supersedes EN ISO 8765:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

24、 Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8765:2011 has been approved by CEN as a EN ISO 8765:2011

25、 without any modification. “ DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) 3 Introduction This International Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following: a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016

26、and ISO 8765); b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676); c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts with flange (ISO 4162, ISO

27、 15071 and ISO 15072); e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670). DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) 4 1 Scope This International Standard specifies the characteristics of hexagon head bolts with metric fine pitch thread with

28、nominal thread diameters, d, from 8 mm to 64 mm, of product grade A for nominal thread diameters, d, from 8 mm to 24 mm and nominal lengths, l, up to and including 10d or 150 mm, whichever is the shorter, and of product grade B for nominal thread diameters, d, over 24 mm or nominal lengths, l, over

29、10d or 150 mm, whichever is the shorter. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1. It i

30、s intended that coarse thread bolts according to ISO 4014 be the first choice. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the ref

31、erenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 261, ISO general-purpose metric screw threads General plan ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 898-1, Mechanical propert

32、ies of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 3269, Fasteners Acceptance inspection ISO 350

33、6-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electroplated coatings ISO 4753, Fasteners Ends of parts with external ISO metric thread ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product

34、grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts IS

35、O 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) 5 3 Dimensions See Figure 1 and Tables 1 and 2. Symbols and descriptions of dimensions are specified in ISO 225. Dimensions in millimetres a = 15 to 30. b Point shall be chamfered in acco

36、rdance with ISO 4753. c Incomplete thread u u 2P. d Reference datum for dw.e Maximum underhead fillet. fdsapplies if values of ls,minare specified. Figure 1 DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) 6 Table 1 Preferred threads Dimensions in millimetres Thread (d P) M8 1 M10 1 M12 1,5 M16 1,5 M20

37、1,5 M24 2 M30 2 M36 3 M42 3 M48 3 M56 4 M64 4 a 22 26 30 38 46 54 66 b 28 32 36 44 52 60 72 84 96 108 b ref. c 41 45 49 57 65 73 85 97 109 121 137 153 max. 0,60 0,60 0,60 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0 c min. 0,15 0,15 0,15 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3 0,3 damax. 9,2 11,2 13,7 17,7 22,4 26,4

38、 33,4 39,4 45,6 52,6 63 71 dsnom. = max. 8,00 10,00 12,00 16,00 20,00 24,00 30,00 36,00 42,00 48,00 56,00 64,00 A 7,78 9,78 11,73 15,73 19,67 23,67 Product gradeB min. 7,64 9,64 11,57 15,57 19,48 23,48 29,48 35,38 41,38 47,38 55,26 63,26 A 11,63 14,63 16,63 22,49 28,19 33,61 dwProduct gradeB min. 11

39、,47 14,47 16,47 22 27,7 33,25 42,75 51,11 59,95 69,45 78,66 88,16 A 14,38 17,77 20,03 26,75 33,53 39,98 e Product gradeB min. 14,20 17,59 19,85 26,17 32,95 39,55 50,85 60,79 71,3 82,6 93,56 104,86 lfmax. 2 2 3 3 4 4 6 6 8 10 12 13 nom. 5,3 6,4 7,5 10 12,5 15 18,7 22,5 26 30 35 40 max. 5,45 6,58 7,68

40、 10,18 12,715 15,215 Product grade A min. 5,15 6,22 7,32 9,82 12,285 14,785 max. 5,54 6,69 7,79 10,29 12,85 15,35 19,12 22,92 26,42 30,42 35,5 40,5 k Product grade B min. 5,06 6,11 7,21 9,71 12,15 14,65 18,28 22,08 25,58 29,58 34,5 39,5 A 3,61 4,35 5,12 6,87 8,6 10,35 kwdProduct gradeB min. 3,54 4,2

41、8 5,05 6,8 8,51 10,26 12,8 15,46 17,91 20,71 24,15 27,65 r min. 0,4 0,4 0,6 0,6 0,8 0,8 1 1 1,2 1,6 2 2 nom. = max. 13,00 16,00 18,00 24,00 30,00 36,00 46 55,0 65,0 75,0 85,0 95,0 A 12,73 15,73 17,73 23,67 29,67 35,38 s Product gradeB min. 12,57 15,57 17,57 23,16 29,16 35 45 53,8 63,1 73,1 82,8 92,8

42、 7 DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) Table 1 (continued) Dimensions in millimetres Thread (d P) M8 1 M10 1 M12 1,5 M16 1,5 M20 1,5 M24 2 M30 2 M36 3 M42 3 M48 3 M56 4 M64 4 Product grade A B lsand lgel lslglslglslglslglslglslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min.

43、 max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. 35 34,5 35, 40 39,5 40,5 11,75 18 For sizes above the solid, bold, stepped line, see ISO 8676. 45 44,5 45,5 16,75 23 11,5 19 50 49,5 50,5 21,75 28 16,5 24 11,25 20 55 54,4 55,6 26,75 33 21,5 29

44、16,25 25 60 59,4 60,6 31,75 38 26,5 34 21,25 30 65 64,4 65,6 36,75 43 31,5 39 26,25 35 17 27 70 69,4 70,6 41,75 48 36,5 44 31,25 40 22 32 80 79,4 80,6 51,75 58 46,5 54 41,25 50 32 42 21,5 34 90 89,3 90,7 88,25 91,75 56,5 64 51,25 60 42 52 31,5 44 100 99,3 100,7 98,25 101,75 66,5 74 61,25 70 52 62 41

45、,5 54 31 46 110 109,3 110,7 108,25 111,75 71,25 80 62 72 51,5 64 41 56 120 119,3 120,7 118,25 121,75 81,25 90 72 82 61,5 74 51 66 36,5 54 130 129,2 130,8 128 132 76 86 65,5 78 55 70 40,5 58 140 139,2 140,8 138 142 86 96 75,5 88 65 80 50,5 68 36 56 150 149,2 150,8 148 152 96 106 85,5 98 75 90 60,5 78

46、 46 66 160 158 162 106 116 95,5 108 85 100 70,5 88 56 76 41,5 64 180 178 182 115,5 128 105 120 90,5 108 76 96 61,5 84 200 197,7 202,3 135,5 148 125 140 110,5 128 96 116 81,5 104 67 92 220 217,7 222,3 132 147 117,5 135 103 123 88,5 111 74 99 55,5 83 240 237,7 242,3 152 167 137,5 155 123 143 108,5 131

47、 94 119 75,5 103 260 257,4 262,6 157,5 175 143 163 128,5 151 114 139 95,5 123 77 107 280 277,4 282,6 177,5 195 163 183 148,5 171 134 159 115,5 143 97 127 300 297,4 302,6 197,5 215 183 203 168,5 191 154 179 135,5 163 117 147 8 DIN EN ISO 8765:2011-06 EN ISO 8765:2011 (E) Table 1 (continued) Dimension

48、s in millimetres Thread (d P) M8 1 M10 1 M12 1,5 M16 1,5 M20 1,5 M24 2 M30 2 M36 3 M42 3 M48 3 M56 4 M64 4 Product grade A B lsand lgel lslglslglslglslglslglslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. 320 3