DIN EN ISO 8469-2013 Small craft - Non-fire-resistant fuel hoses (ISO 8469 2013) German version EN ISO 8469 2013《小型船舶 非耐火燃料软管(ISO 8469-2013) 德文版本EN ISO 8469-2013》.pdf

《DIN EN ISO 8469-2013 Small craft - Non-fire-resistant fuel hoses (ISO 8469 2013) German version EN ISO 8469 2013《小型船舶 非耐火燃料软管(ISO 8469-2013) 德文版本EN ISO 8469-2013》.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 8469-2013 Small craft - Non-fire-resistant fuel hoses (ISO 8469 2013) German version EN ISO 8469 2013《小型船舶 非耐火燃料软管(ISO 8469-2013) 德文版本EN ISO 8469-2013》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、December 2013 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 47.080!%*r“2077995www.din.deDDIN EN ISO 8469Small craft Non-fire-resistant fuel hoses (ISO 8469:2013);English version EN ISO 8469:2013,English translation of DIN EN ISO 8469:2013-12Kleine Wasserfahrzeuge Nicht feuerwiderstandsfhige Kraftstoffschluche (ISO 8469:2013);Englische Fassung EN ISO 8469:

3、2013,Englische bersetzung von DIN EN ISO 8469:2013-12Petits navires Tuyaux souples pour carburant non rsistants au feu (ISO 8469:2013);Version anglaise EN ISO 8469:2013,Traduction anglaise de DIN EN ISO 8469:2013-12SupersedesDIN EN ISO 8469:2006-10www.beuth.deIn case of doubt, the German-language or

4、iginal shall be considered authoritative.Document comprises 14 pages11.13 DIN EN ISO 8469:2013-12 2 A comma is used as the decimal marker. National foreword This document (EN ISO 8469:2013) has been prepared by Technical Committee ISO/TC 188 “Small craft” in collaboration with Technical Committee CE

5、N/BT/WG 69 “Small craft” (Secretariat: SIS, Sweden). The responsible German body involved in its preparation was the Normenstelle Schiffs- und Meerestechnik (Shipbuilding and Marine Technology Standards Committee), Working Committee NA 132-08-01 AA Kleine Wasserfahrzeuge. The European Standards refe

6、rred to in this document have been published as DIN EN or DIN EN ISO Standards with the same number. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 3 DIN 323-1 ISO 1307 DIN EN ISO 1307 ISO 1402 DIN EN ISO 1402 ISO 7233 DIN EN ISO 7233

7、ISO 7326 DIN EN 7326 Amendments This standard differs from DIN EN ISO 8469:2006-10 as follows: a) a standardized test liquid for the bursting pressure test has been specified; b) the conditions for the fuel permeation test have been modified; c) the standard has been editorially revised. Previous ed

8、itions DIN EN ISO 8469: 1995-06, 2006-10 DIN EN ISO 8469 Corrigendum 1: 2001-03 National Annex NA (informative) Bibliography DIN 323-1:1974, Preferred Numbers and Series of Preferred Numbers Basic Values, Calculated Values, Rounded Values DIN EN ISO 1307, Rubber and plastics hoses Hose sizes, minimu

9、m and maximum inside diameters, and tolerances on cut-to-length hoses DIN EN ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testing DIN EN ISO 7233:2008-07, Rubber and plastics hoses and hose assemblies Determination of resistance to vacuum DIN EN ISO 7326:2009-10, Rubber and pl

10、astics hoses Assessment of ozone resistance under static conditions EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8469 July 2013 ICS 47.080 Supersedes EN ISO 8469:2006English Version Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013) Petits navires - Tuyaux souples pour carburant

11、 non rsistants au feu (ISO 8469:2013) Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfhige Kraftstoffschluche (ISO 8469:2013) This European Standard was approved by CEN on 8 June 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving

12、 this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offici

13、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of A

14、ustria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sw

15、eden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national

16、 Members. Ref. No. EN ISO 8469:2013: EContents Page Foreword . 3 1 Scope . 4 2 Normative references. 4 3 General requirements 4 4 Hose inner diameter . 4 5 Physical tests on finished hose 5 5.1 General 5 5.2 Test liquids . 5 5.3 Bursting pressure 5 5.4 Vacuum collapse test. 6 5.5 Volume change in te

17、st liquids 6 5.6 Mass reduction of test hose 6 5.7 Effect of ozone 6 5.8 Fuel permeation 6 5.9 Cold flex test . 7 5.10 Abrasion test 38 mm inner diameter and larger fuel fill hose with embedded wire reinforcement . 7 5.11 Dry heat resistance test . 7 5.12 Oil resistance test 7 5.13 Adhesion test 7 6

18、 Marking 7 Annex A (normative) Fuel permeation test (or equivalent test method) 9 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC . 11 Bibliography 12 DIN EN ISO 8469:2013-12EN ISO 8469:2013

19、 (E) 2This document (EN ISO 8469:2013) has been prepared by Technical Committee ISO/TC 188 “Small craft”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2014, and conflicting national sta

20、ndards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN I

21、SO 8469:2006. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document

22、. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, G

23、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 8469:2013 has been approved by CEN as EN ISO 8469:

24、2013 without any modification. ForewordDIN EN ISO 8469:2013-12EN ISO 8469:2013 (E)3Small craft Non-fire-resistant fuel hoses1 ScopeThis International Standard specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol and diesel

25、 fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m.It applies to hoses for small craft with permanently installed f

26、uel systems.Specifications for fire-resistant hoses are given in ISO 78401. Specifications for permanently installed fuel systems are given in ISO 100882.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its appl

27、ication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3:1973, Preferred numbers Series of preferred numbersISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside

28、diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1817:2011, Rubber, vulcanized or thermoplastic Determination of the effect of liquidsISO 7233:2006, Rubber and plastics hoses and hose assemblies Determination of resistance

29、 to vacuumISO 7326:2006, Rubber and plastics hoses Assessment of ozone resistance under static conditionsEN 14214:2008+Amd.1:2009, Automotive fuels Fatty acid methyl esters (FAME) for diesel engines Requirements and test methods3 General requirementsHoses complying with this International Standard s

30、hall present a smooth inner surface free from pores, other defects and chemical contaminants.Hoses shall demonstrate suitability for marine use by complying with the requirements of the tests in Clause 5. They shall be marked according to Clause 6.4 Hose inner diameterTable 1 gives some of the inner

31、 diameters based on series R 10 of ISO 3:1973. Tolerances shall conform to ISO 1307.DIN EN ISO 8469:2013-12EN ISO 8469:2013 (E) 4N1) National footnote: EN 14214:2008+Amd.1:2009 was replaced by EN 14214:2012. N1)Table 1 Inner diameters and tolerancesDimensions in millimetresInner diameter, d Toleranc

32、e3,245 0,56,3789,51012,5161920 0,752531,538 1,25405063 1,55 Physical tests on finished hose5.1 GeneralNew samples shall be used for each of the tests below.5.2 Test liquidsa) Petrol:1) by volume 100 % liquid 2 specified in ISO 1817:2011, Table A.2;AND2) a mixture of by volume 90 % of liquid 2 specif

33、ied in ISO 1817:2011, Table A.2 and 10 % by volume of ethanol.b) Diesel:1) a mixture of by volume 90 % liquid F specified in ISO 1817:2011 and 10 % by volume of Fatty Acid Methyl Esters (FAME), specified in EN 14214:2008+Amd.1:2009.5.3 Bursting pressureFor each test liquids as specified in 5.2, fill

34、 three hoses or sample lengths from the hoses and store them for 40 days in air at a temperature of 40 C 2 C.DIN EN ISO 8469:2013-12EN ISO 8469:2013 (E)5Empty the liquid out and fill the hoses or sample lengths with cold water; subject them to hydrostatic pressure as specified in ISO 1402.The bursti

35、ng pressure shall be at least 1,4 MPa for hoses with an inner diameter of 10 mm or less and 1,00 MPa for hoses with an inner diameter of more than 10 mm.5.4 Vacuum collapse testCarry out the test in accordance with ISO 7233:2006, method A, using the test conditions specified in Table 2.Table 2 Press

36、ure conditions for the vacuum collapse testInner diameter, d mmVacuum kPad 10 8010 25 No test requiredThe test duration shall be 60 s and the diameter of the sphere 0,8 d (inner diameter of the hose). The sphere shall pass freely through the hose while under vacuum.5.5 Volume change in test liquidsD

37、etermine the change in volume of the hose (tube and cover) by the procedure specified in ISO 1817.Completely submerge the test pieces in test liquids as specified in 5.2 at a temperature of 40 C 2 C for 40 days.If the hose is made of a homogeneous compound (with or without reinforcement), the swelli

38、ng shall not exceed 35 % by volume as measured by displacement in water. For hose with an inner layer of fuel-resistant material and a cover of another material mainly intended for weather and ozone resistance, the increase in volume shall not exceed 35 % for the tube and 120 % for the cover.5.6 Mas

39、s reduction of test hoseDetermine the reduction in mass of the hose by the procedure specified in ISO 1817. Fill three hoses or sample lengths from the hoses with test liquids, as specified in 5.2, and store them for 40 days in air at a temperature of 40 C 2 C.The reduction in mass of the inner laye

40、r shall not exceed 8 % of the initial mass of the test pieces.NOTE A reduction in mass of 8 % corresponds to a decrease in volume of approximately 10 %.5.7 Effect of ozoneThe hose shall be tested in accordance with ISO 7326:2006, method 1. The sample shall show no visible cracks at 7 magnification.5

41、.8 Fuel permeationThe permeation rate for the hoses shall be determined according to the method specified in Annex A or an equivalent test method. The hoses shall be classified in the following way and marked in accordance with Clause 6:Type 1: hoses with a permeation rate of 100 g/m2or less per 24

42、h;Type 2: hoses with a permeation rate of over 100 g/m2per 24 h, up to and including 300 g/m2per 24 h.DIN EN ISO 8469:2013-12EN ISO 8469:2013 (E) 65.9 Cold flex testFor straight hoses of 19 mm inner diameter and smaller, condition three hose samples for 5 h at an ambient temperature of 20 C 2 C. Fle

43、x in the cold chamber through 180 from the centreline to a diameter of 10 times the maximum outside diameter of the hose. The flexing shall take place within 4 s and the hose shall not fracture or show any cracks, checks or breaks in the tube or cover.For straight hoses larger than 19 mm inner diame

44、ter and all pre-formed hoses, prepare three samples (100 5) mm (6 1) mm from the whole hose wall and condition them for 5 h at a temperature of 20 C 2 C in an unrestrained loop, position between two jaws 50 mm wide and 64 mm apart. While in the cold chamber, bring the jaws together rapidly until the

45、y are 25 mm apart. The samples shall not fracture or show any cracks, checks or breaks.5.10 Abrasion test 38 mm inner diameter and larger fuel fill hose with embedded wire reinforcementHose samples of 38 mm inner diameter shall be selected for the test. Larger inner diameter hose sizes to be qualifi

46、ed by the test shall not have a cover thickness or construction less than those of the test samples.Three identical 38 mm inner diameter hose samples shall be tested. Condition hose samples for at least 24 h at a temperature of 23 C 2 C and 50 % 5 % relative humidity. The test hose shall be mandrel-

47、 (core-) supported and rotate at a constant speed of 80 rev/min 2 rev/min. Subject the hose to a laterally moving abrasive surface, i.e. 80 grit aluminium oxide (Al2O3) emery cloth, parallel to the longitudinal axis of the hose. The abrasive surface shall be (25 5) mm (75 5) mm affixed to a hard sur

48、face which will cycle back and forth 75 mm 5 mm in each direction while loaded with a constant normal force of 45 N 5 N. One test cycle shall equal one 360 rotation of the outside diameter of the hose and one back and forth movement of the abrasive surface. After 1 000 cycles, the three test samples

49、 shall have no helical wire reinforcement exposed at the point of contact with the abrasive surface.5.11 Dry heat resistance testAfter heat ageing for 70 h at a temperature of 100 C 2 C, samples taken from the cover material shall not have a reduction in tensile strength of more than 20 % or a reduction in elongation at break of more than 50 % of the original values of the unheated samples.5