DIN EN ISO 6149-1-2007 Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1 Ports with truncated hous.pdf

《DIN EN ISO 6149-1-2007 Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1 Ports with truncated hous.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 6149-1-2007 Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1 Ports with truncated hous.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、May 2007DEUTSCHE NORM English price group 9No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.100.60!,xb8“9856321www.d

2、in.deDDIN EN ISO 6149-1Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2006)English version of DIN EN ISO 6149-1:2007-05Leitungsanschlsse fr Fluidtechnik und allg

3、emeine Anwendung Einschraublcher und Einschraubzapfen mit metrischem Gewinde nach ISO 261 undO-Ring-Abdichtung Teil 1: Einschraublcher mit Ansenkung fr O-Ring-Abdichtung (ISO 6149-1:2006)Englische Fassung DIN EN ISO 6149-1:2007-05SupersedesDIN ISO 6149-1:1996-11www.beuth.deDocument comprises 11 page

4、s 08.07DIN EN ISO 6149-1:2007-05 2 National foreword This standard has been published in accordance with a decision taken by ECISS/TC 29 “Steel tubes and fittings for steel tubes” (Secretariat: UNI, Italy) to adopt, without alteration, International Standard ISO 6149-1 as a European Standard. The re

5、sponsible German body involved in its preparation was the Normenausschuss Rohrleitungen und Dampfkesselanlagen (Pipelines and Boilers Standards Committee), Technical Committee NA 082-00-07 AA Rohrverschraubungen. The DIN Standards corresponding to the International Standards referred to in clause 2

6、of the EN are as follows: ISO 261 DIN ISO 261 ISO 965-1 DIN ISO 965-1 ISO 5598 E DIN ISO 5598 ISO 6149-2 DIN EN ISO 6149-2 ISO 6149-3 DIN EN ISO 6149-3 Amendments This standard differs from DIN ISO 6149-1:1996-11 as follows: a) The current standards on screwed connections and relevant tests have bee

7、n taken into account. b) Port identification is optional. c) Some diameters and radii have been changed. d) The standard has been editorially revised. Previous editions DIN 3852-3: 1991-11 DIN ISO 6149-1: 1996-11 National Annex NA (informative) Bibliography DIN EN ISO 6149-2, Connections for hydraul

8、ic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends DIN EN ISO 6149-3, Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 me

9、tric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data E DIN

10、ISO 5598, Fluid power systems and components Vocabulary EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6149-1 February 2007 ICS 23.100.40 English Version Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Por

11、ts with truncated housing for O-ring seal (ISO 6149-1:2006) Raccordements pour transmissions hydrauliques et applications gnrales - Orifices et lments mles filetage mtrique ISO 261 et joint torique - Partie 1: Orifices joint torique dans un logement tronconique (ISO 6149-1:2006) Leitungsanschlsse fr

12、 Fluidtechnik und allgemeine Anwendung - Einschraublcher und Einschraubzapfen mit metrischem Gewinde nach ISO 261 und O-Ring-Abdichtung - Teil 1: Einschraublcher mit Ansenkung fr O-Ring-Abdichtung (ISO 6149-1:2006) This European Standard was approved by CEN on 4 February 2007. CEN members are bound

13、to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN

14、Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status

15、 as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, S

16、lovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worl

17、dwide for CEN national Members. Ref. No. EN ISO 6149-1:2007: EForeword The text of ISO 6149-1:2006 has been prepared by Technical Committee ISO/TC 131 “Fluid power systems” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 6149-1:2007 by Technical Committe

18、e ECISS/TC 29 “Steel tubes and fittings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2007, and conflicting national standards s

19、hall be withdrawn at the latest by August 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Ger

20、many, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 6149-1:2006 has been approved by CEN as EN ISO 6149-1:2007 witho

21、ut any modifications. 2 EN ISO 6149-1:2007 (E) Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. In general applications, a fluid (liquid or gas) may be conveyed under pressure. Components are connected thro

22、ugh their threaded ports by fluid conductor connectors to tubes and pipes or to hose connectors and hoses. Ports are an integral part of fluid power components, such as pumps, motors, valves, cylinders, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applicati

23、ons, ISO/TC 131/SC 4 recommends that the ISO 6149 series be used because these International Standards specify ports and stud ends with metric threads and O-ring sealing and because the subcommittee would like to help users by recommending one preferred system. ISO/TC 131/SC 4 further recommends tha

24、t threaded ports and stud ends in accordance with the ISO 1179 series, ISO 9974 series and ISO 11926 series not be used for new designs in hydraulic fluid power applications; these International Standards are maintained because they specify ports and stud ends that are currently used in hydraulic sy

25、stems worldwide. 3 EN ISO 6149-1:2007 (E) 1 Scope This part of ISO 6149 specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends detailed in ISO 6149-2 and ISO 6149-3. Ports in accordance with this part of ISO 6149 may be used at working pressures up to 63 MPa 6

26、30 bar1) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149-2 and ISO 6149-3 for pressure ratings. Users of this part of ISO 6149 should ensure that

27、 there is sufficient material around the port to maintain the pressure. NOTE The Introduction of this part of ISO 6149 gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications. 2 Normative references The following referenced documents are indispe

28、nsable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 261, ISO general purpose metric screw threads General plan ISO 965-1, ISO general purpose m

29、etric screw threads Tolerances Part 1: Principles and basic data ISO 2306, Drills for use prior to tapping screw threads ISO 55982), Fluid power systems and components Vocabulary ISO 6149-2, Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-r

30、ing sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends 1) 1 bar = 0,1 MPa = 105Pa; 1 MPa = 1 N/mm2. 2) To be published. (Revision of ISO 5598:1985). 4 EN ISO 6149-1:2007 (E) ISO 6149-33), Connections for fluid power and general use Ports and stud en

31、ds with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends 3 Terms and definitions For the purposes of this part of ISO 6149, the terms and definitions given in ISO 5598 apply. 4 Dimensions Ports shall conform to th

32、e dimensions shown in Figure 1 and given in Table 1. Dimensions in millimetres, values for surface roughness in micrometres aOptional identification of port; see Figure 2 and Clause 7. bPitch diameter. cThis dimension only applies when tap drill cannot pass through entire boss. dGauging. eReference

33、only. fThread. Figure 1 Port 3) To be published. (Revision of ISO 6149-3:1993). 5 EN ISO 6149-1:2007 (E) Table 1 Port dimensions Dimensions in millimetres Threadad2d3bd4d5L1L2cL3L4Z (d1 P) widedmin. narrowemin. ref. 0,10+0,40+min. max. min. 1 M8 1 17 14 3 12,5 9,1 1,6 11,5 1 10 12 M10 1 20 16 4,5 14

34、,5 11,1 1,6 11,5 1 10 12 M12 1,5 23 19 6 17,5 13,8 2,4 14 1,5 11,5 15 M14 1,5f25 21 7,5 19,5 15,8 2,4 14 1,5 11,5 15 M16 1,5 28 24 9 22,5 17,8 2,4 15,5 1,5 13 15 M18 1,5 30 26 11 24,5 19,8 2,4 17 2 14,5 15 M20 1,5g33 29 27,5 21,8 2,4 2 14,5 15 M22 1,5 33 29 14 27,5 23,8 2,4 18 2 15,5 15 M27 2 40 34

35、18 32,5 29,4 3,1 22 2 19 15 M30 2 44 38 21 36,5 32,4 3,1 22 2 19 15 M33 2 49 43 23 41,5 35,4 3,1 22 2,5 19 15 M42 2 58 52 30 50,5 44,4 3,1 22,5 2,5 19,5 15 M48 2 63 57 36 55,5 50,4 3,1 25 2,5 22 15 M60 2 74 67 44 65,5 62,4 3,1 27,5 2,5 24,5 15 aConforming to ISO 261, tolerance grade 6H in accordance

36、 with ISO 965-1. Tap drills in accordance with ISO 2306, class 6H. bFor reference only. Connecting hole application may require a different size. cThe tap drill depths given require the use of a bottoming tap to produce the specified full thread lengths. Where standard taps are used, the tap drill d

37、epths shall be increased accordingly. dSpotface diameter with identification ridge. eSpotface diameter without identification ridge. fPreferred for diagnostic port applications. gFor cartridge valve cavity applications only (see ISO 7789). 6 EN ISO 6149-1:2007 (E) Dimensions in millimetres aThread.

38、Figure 2 Optional port identification Table 2 Optional port identification4)Dimensions in millimetres Thread d6(d1 P) 0,50+M8 1 14 M10 1 16 M12 1,5 19 M14 1,5 21 M16 1,5 24 M18 1,5 26 M20 1,5a29 M22 1,5 29 M27 2 34 M30 2 38 M33 2 43 M42 2 52 M48 2 57 M60 2 67 aFor cartridge valve cavities only (see

39、ISO 7789). 4) See Clause 7. 7 EN ISO 6149-1:2007 (E) 5 Test methods Ports shall be tested along with stud ends in accordance with the test methods and requirements given in ISO 6149-2 and ISO 6149-3. For rated pressures lower than those specified in ISO 6149-2 and ISO 6149-3, the test pressures shal

40、l be agreed upon between the manufacturer and user. 6 Designation of ports The ports shall be designated by a) “Port”; b) reference to this part of ISO 6149, i.e. ISO 6149-1; c) thread size (d1 P). EXAMPLE A port in accordance with this part of ISO 6149, with a thread M18 1,5 is designated as follow

41、s: Port ISO 6149-1 - M18 1,5 7 Identification Each port in accordance with this part of ISO 6149 shall be identified by a raised ring conforming to the dimensions given in Figure 2 and Table 2, or by permanently marking “metric” or “M” next to the port, or by a permanent identification label on the

42、component to read “ISO 6149-1 metric ports”. 8 Identification statement (reference to this part of ISO 6149) It is strongly recommended to manufacturers who have chosen to conform to this International Standard that the following statement be used in test reports, catalogues and sales literature: “P

43、orts conform to ISO 6149-1:2006, Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal.” 8 EN ISO 6149-1:2007 (E) Bibliography 1 ISO 1101, Technical drawings Geometrical tolerancin

44、g Tolerances of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings 2 ISO 1179-15), Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports 3 ISO 1179-25),

45、 Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 2: Heavy-duty (S series) and light-duty (L series) stud ends and elastomeric sealing (type E) 4 ISO 1179-35), Connections for general use and fluid power Ports and

46、stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) 5 ISO 1179-45), Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or me

47、tal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) 6 ISO 1302, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation 7 ISO 6410-1, Technical drawings Screw threads and threaded parts Part 1: General con

48、ventions 8 ISO 7789, Hydraulic fluid power Two-, three- and four-port screw-in cartridge valves Cavities 9 ISO 9974-1, Connections for general use and fluid power Ports and stud ends with ISO 261 threads or elastomeric or metal-to-metal sealing Part 1: Threaded ports 10 ISO 9974-2, Connections for g

49、eneral use and fluid power Ports and stud ends with ISO 261 threads or elastomeric or metal-to-metal sealing Part 2: Stud ends with elastomeric sealing (type E) 11 ISO 9974-3, Connections for general use and fluid power Ports and stud ends with ISO 261 threads or elastomeric or metal-to-metal sealing Part 3: Stud ends with metal-to-metal sealing (type B)