DIN EN ISO 2010-2011 Slotted raised countersunk head screws - Product grade A (ISO 2010 2011) German version EN ISO 2010 2011《开槽半沉头螺钉 产品等级A级(ISO 2010-2011) 德文版 EN ISO 2010-2011》.pdf

《DIN EN ISO 2010-2011 Slotted raised countersunk head screws - Product grade A (ISO 2010 2011) German version EN ISO 2010 2011《开槽半沉头螺钉 产品等级A级(ISO 2010-2011) 德文版 EN ISO 2010-2011》.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 2010-2011 Slotted raised countersunk head screws - Product grade A (ISO 2010 2011) German version EN ISO 2010 2011《开槽半沉头螺钉 产品等级A级(ISO 2010-2011) 德文版 EN ISO 2010-2011》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、December 2011 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 21.060.10!$xZP“1855545www.din.deDDIN EN ISO 2010Slotted raised countersunk head screws Product grade A (ISO 2010:2011)English translation of DIN EN ISO 2010:2011-12Linsensenkschrauben mit Schlitz Produktklasse A (ISO 2010:2011)Englische bersetzung von DIN EN ISO 2010:2011-12Vis mtaux tte fraise bo

3、mbe fendue Grade A (ISO 2010:2011)Traduction anglaise de DIN EN ISO 2010:2011-12SupersedesDIN EN ISO 2010:1994-10www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1312.11 DIN EN ISO 2010:2011-12 2 A comma is used as the decimal marke

4、r. National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Mechanische

5、Verbin-dungselemente (Fasteners Standards Committee), Working Committee NA 067-00-05 AA Kleinschrauben und gewindeformende Schrauben. The DIN 4000-160-3 tabular layout of article characteristics shall apply to screws covered in this standard. The DIN Standards corresponding to the International Stan

6、dards referred to in Clause 2 of this document are as follows: ISO 225 DIN EN ISO 225 ISO 261 DIN ISO 261 ISO 898-1 DIN EN ISO 898-1 ISO 965-2 DIN ISO 965-2 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 7721

7、DIN EN 27721 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 ISO 16048 DIN EN ISO 16048 Amendments This standard differs from DIN EN ISO 2010:1994-10 as follows: a) normative references are now undated; b) in Table 2, zinc-flake coatings in accordance with ISO 10683 and requir

8、ements for passivation in accordance with ISO 16048 have been added; c) Annex ZA has been deleted. Previous editions DIN 964: 1970-06, 1985-05, 1990-08 DIN ISO 2010: 1990-08 DIN EN ISO 2010: 1994-10 DIN EN ISO 2010:2011-12 3 National Annex NA (informative) Bibliography DIN 4000-160, Tabular layout o

9、f product properties Part 160: Fasteners with external thread DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general requirements DIN EN 27721, Countersunk head screw Head configuration and gauging DIN EN 28839, Mechanical properties of fasteners Nonferrous meta

10、l bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and f

11、ine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, scr

12、ews, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 965-2, ISO general purp

13、ose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN EN ISO 2010:2011-12 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPEN

14、NE EUROPISCHE NORM EN ISO 2010 September 2011 ICS 21.060.10 Supersedes EN ISO 2010:1994English Version Slotted raised countersunk head screws - Product grade A (ISO 2010:2011) Vis mtaux tte fraise bombe fendue - Grade A (ISO 2010:2011) Linsensenkschrauben mit Schlitz - Produktklasse A (ISO 2010:2011

15、) This European Standard was approved by CEN on 8 August 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical ref

16、erences concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a C

17、EN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

18、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Ave

19、nue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2010:2011: EContents Page Foreword3 1 Scope 4 2 Normative references 4 3 Dimensions.5 4 Specifications and reference International Standards 8

20、5 Designation 8 Bibliography 9 DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 2 Foreword This document (EN ISO 2010:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This Europea

21、n Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at the latest by March 2012. Attention is drawn to the possibility that some of the elements o

22、f this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2010:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following cou

23、ntries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slo

24、venia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 2010:2011 has been approved by CEN as a EN ISO 2010:2011 without any modification. DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 3 1 Scope This International Standard specifies the characteristics of counters

25、unk slotted raised head screws of product grade A and with threads from M1,6 to M10 inclusive. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1

26、, ISO 965-2 and ISO 3506-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

27、. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 261, ISO general purpose metric screw threads General plan ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes

28、Coarse thread and fine pitch thread ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainle

29、ss steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements IS

30、O 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings ISO 16048, Passivation of corrosion-resistant stainless

31、-steel fasteners DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 4 3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225. The shank diameter is approximately equal to the pitch diameter or equal to the permissible major thread diameter. Key 1 as-rolled e

32、nd 2 edge (rounded or flat) Figure 1 DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 5 Table 1 Dimensions Dimensions in millimetres Thread, d M1,6 M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 Pb0,35 0,4 0,45 0,5 0,6 0,7 0,8 1 1,25 1,5 a max. 0,7 0,8 0,9 1 1,2 1,4 1,6 2 2,5 3 b min. 25 25 25 25 38 38 38 38 38 38 T

33、heoretical max. 3,6 4,4 5,5 6,3 8,2 9,4 10,4 12,6 17,3 20 nom. = max. 3,0 3,8 4,7 5,5 7,30 8,40 9,30 11,30 15,80 18,30 dkcActual min. 2,7 3,5 4,4 5,2 6,94 8,04 8,94 10,87 15,37 17,78 f 0,4 0,5 0,6 0,7 0,8 1 1,2 1,4 2 2,3 kcnom. = max. 1 1,2 1,5 1,65 2,35 2,7 2,7 3,3 4,65 5 nom. 0,4 0,5 0,6 0,8 1 1,2

34、 1,2 1,6 2 2,5 max. 0,60 0,70 0,80 1,00 1,20 1,51 1,51 1,91 2,31 2,81 n min. 0,46 0,56 0,66 0,86 1,06 1,26 1,26 1,66 2,06 2,56 r max. 0,4 0,5 0,6 0,8 0,9 1 1,3 1,5 2 2,5 rf 3 4 5 6 8,5 9,5 9,5 12 16,5 19,5 max. 0,80 1,0 1,2 1,45 1,7 1,9 2,4 2,8 3,7 4,4 t min. 0,64 0,8 1,0 1,20 1,4 1,6 2,0 2,4 3,2 3,

35、8 x max. 0,9 1 1,1 1,25 1,5 1,75 2 2,5 3,2 3,8 la dnom. min. max. Approximate mass, in kilograms per 1 000 pieces ( = 7,85 kg/dm3) (for information only) 2,5 2,3 2,7 0,062 3 2,8 3,2 0,067 0,119 4 3,76 4,24 0,078 0,138 0,242 5 4,76 5,24 0,09 0,156 0,272 0,395 6 5,76 6,24 0,102 0,175 0,302 0,439 0,729

36、 1,07 8 7,71 8,29 0,125 0,212 0,362 0,527 0,849 1,23 1,73 2,79 10 9,71 10,29 0,145 0,249 0,422 0,615 0,969 1,39 1,97 3,14 6,89 12 11,65 12,35 0,165 0,287 0,482 0,703 1,09 1,54 2,21 3,49 7,53 11,4 (14) 13,65 14,35 0,185 0,325 0,543 0,791 1,21 1,7 2,45 3,84 8,17 12,5 16 15,65 16,35 0,205 0,362 0,603 0

37、,879 1,33 1,85 2,69 4,19 8,81 13,5 20 19,58 20,42 0,436 0,723 1,06 1,57 2,17 3,17 4,89 10,1 15,5 25 24,58 25,42 0,874 1,28 1,87 2,56 3,77 5,77 11,7 18 30 29,58 30,42 1,5 2,17 2,95 4,37 6,64 13,3 20,6 35 34,5 35,5 2,47 3,34 4,97 7,52 14,9 23,1 40 39,5 40,5 3,73 5,57 8,39 16,5 25,6 45 44,5 45,5 6,16 9

38、,27 18,1 28,1 50 49,5 50,5 6,76 10,1 19,7 30,7 DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 6 Table 1 (continued) Dimensions in millimetres Thread, d M1,6 M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 la dnom. min. max. Approximate mass, in kilograms per 1 000 pieces ( = 7,85 kg/dm3) (for information only) (55)

39、 54,05 55,95 11 21,3 33,2 60 59,05 60,95 11,9 22,9 35,7 (65) 64,05 65,95 24,5 38,2 70 69,05 70,95 26,1 40,8 (75) 74,05 75,95 27,7 43,3 80 79,05 80,95 29,3 45,8 NOTE Preferred lengths are shown between the solid, bold, stepped lines. aSizes in parentheses should be avoided if possible. bP is the pitc

40、h of the thread. cSee ISO 7721. dScrews with nominal lengths above the bold, discontinuous line are threaded up to the head; b = l (k + a). DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 7 4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference Internat

41、ional Standards Material Steel Stainless steel Non-ferrous metal General requirements International Standard ISO 8992 Tolerance class 6g Thread International Standards ISO 261, ISO 965-2 Property class 4.8, 5.8 A2-50, A2-70 Mechanical property International Standards ISO 898-1 ISO 3506-1 ISO 8839 Pr

42、oduct grade A Tolerance International Standard ISO 4759-1 As processed Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Requirements for passivation are specified in ISO 16048. Requirements for el

43、ectroplating are specified in ISO 4042.Finish Coating Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Surface integrity Limits for surface discontinuities are specified in ISO 6157-1. Acceptability Acceptance inspection is specified in IS

44、O 3269. 5 Designation EXAMPLE A countersunk slotted raised head screw with thread M5, nominal length l = 20 mm and property class 4.8 is designated as follows: Countersunk raised head screw ISO 2010 - M5 20 - 4.8 DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 8 Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose bolts 2 ISO 7721, Countersunk head screws Head configuration and gauging DIN EN ISO 2010:2011-12 EN ISO 2010:2011 (E) 9