DIN EN ISO 16148-2016 Gas cylinders - Refillable seamless steel gas cylinders and tubes - Acoustic emission examination (AT) and follow-up ultrasonic examination (UT) for periodic .pdf

《DIN EN ISO 16148-2016 Gas cylinders - Refillable seamless steel gas cylinders and tubes - Acoustic emission examination (AT) and follow-up ultrasonic examination (UT) for periodic .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 16148-2016 Gas cylinders - Refillable seamless steel gas cylinders and tubes - Acoustic emission examination (AT) and follow-up ultrasonic examination (UT) for periodic .pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、September 2016 English price group 16No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.020.30!%0D“2561333www.din.d

2、eDIN EN ISO 16148Gas cylinders Refillable seamless steel gas cylinders and tubes Acoustic emission examination (AT) and followup ultrasonic examination (UT) for periodic inspection and testing (ISO 16148:2016);English version EN ISO 16148:2016,English translation of DIN EN ISO 16148:2016-09Gasflasch

3、en Wiederbefllbare nahtlose Gasflaschen und Groflaschen aus Stahl Schallemissionsprfung und nachfolgende Ultraschallprfung fr die wiederkehrende Inspektion und Prfung (ISO 16148:2016);Englische Fassung EN ISO 16148:2016,Englische bersetzung von DIN EN ISO 16148:2016-09Bouteilles gaz Bouteilles gaz r

4、echargeables en acier sans soudure et tubes Essais dmission acoustique et examen ultrasonique complmentaire pour linspection priodique et lessai (ISO 16148:2016);Version anglaise EN ISO 16148:2016,Traduction anglaise de DIN EN ISO 16148:2016-09SupersedesDIN EN ISO 16148:200608www.beuth.deDocument co

5、mprises 36 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.09.16 DIN EN ISO 16148:2016-09 2 A comma is used as the decimal marker. National foreword This document (EN ISO 16148:2016) has been prepared by Technical Committee ISO

6、/TC 58 “Gas cylinders” in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was DIN-Normenausschuss Druckgasanlagen (DIN Standards Committee Pressurized Gas Installations), Workin

7、g Committee NA 016-00-03 AA Druckgasflaschen und Ausrstung. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 12713 DIN EN 12713 ISO 12714 DIN EN 12714 ISO 5577 DIN EN ISO 5577 ISO 9712 DIN EN ISO 9712 This standard is intended to be refe

8、renced within the context of the European Agreement on the International Carriage of Dangerous Goods by Road (RID/ADR/ADN). Before applying this standard, users of this standard are to verify whether the provisions of other laws and regulations have been met, particularly those regarding occupationa

9、l safety and health. Amendments This standard differs from DIN EN ISO 16148:2006-08 as follows: a) the scope has been extended to include tubes with a water capacity of up to 3 000 l used for compressed and liquefied gases; b) procedures for ultrasonic examination (UT) follow-up during periodic insp

10、ection, as described in the new Annex A, have been added. Previous editions DIN EN ISO 16148-2: 2006-08 DIN EN ISO 16148:2016-09 3 National Annex NA (informative) Bibliography DIN EN 12713, Screw cap closure systems for plastics containers with a nominal capacity of 20 l to 60 l DIN EN 12714, Plasti

11、cs drums Removable head (open head) drums with a nominal capacity of 25 l to 60 l DIN EN ISO 5577, Non-destructive testing Ultrasonic testing Terminology DIN EN ISO 9712, Non-destructive testing Qualification and certification of NDT personnel DIN EN ISO 16148:2016-09 4 This page is intentionally bl

12、ank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 16148 April 2016 ICS 23.020.30 Supersedes EN ISO 16148:2006English Version Gas cylinders - Refillable seamless steel gas cylinders and tubes - Acoustic emission examination (AT) and follow-up ultrasonic examination (UT) for periodic inspec

13、tion and testing (ISO 16148:2016) Bouteilles gaz - Bouteilles gaz rechargeables en acier sans soudure et tubes - Essais dmission acoustique et examen ultrasonique complmentaire pour linspection priodique et lessai(ISO 16148:2016) Gasflaschen - Wiederbefllbare nahtlose Gasflaschen und Groflaschen aus

14、 Stahl - Schallemissionsprfung und nachfolgende Ultraschallprfung fr die wiederkehrende Inspektion und Prfung(ISO 16148:2016) This European Standard was approved by CEN on 28 November 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

15、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o

16、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

17、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

18、n, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide

19、 for CEN national Members. Ref. No. EN ISO 16148:2016 EEuropean foreword .3Introduction 51 Scope . 62 Normative references 63 Terms and definitions . 64 Operational principles . 85 Personnel qualification . 86 Special considerations to ensure valid tests 96.1 General . 96.2 Acoustic emission examina

20、tion methods . 96.3 Pressurization 96.4 Safety precautions . 107 Acoustic emission examination equipment 108 Acoustic emission examination calibration and equipment verification 128.1 Calibration . 128.2 Equipment verification . 129 Overall procedure. 1210 Real-time evaluation criteria 1311 AT test

21、report 1412 Follow-up ultrasonic examination 15Annex A (normative) Ultrasonic examination (UT) follow-up to acoustic emission examination (AT) 16Annex B (normative) AT equipment specifications .22Annex C (normative) Example instrument settings, examination methods and rejection criteria for MAE.24An

22、nex D (informative) Alternative method for source location .27Annex E (informative) Distance amplitude correction procedures 29Bibliography .32Contents PageDIN EN ISO 16148:2016-09 EN ISO 16148:2016 (E) 2Foreword .4European foreword This document (EN ISO 16148:2016) has been prepared by Technical Co

23、mmittee ISO/TC 58 “Gas cylinders” in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the l

24、atest by October 2016, and conflicting national standards shall be withdrawn at the latest by October 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or al

25、l such patent rights. This document supersedes EN ISO 16148:2006. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following

26、countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway

27、, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 16148:2016 has been approved by CEN as EN ISO 16148:2016 without any modification. DIN EN ISO 16148:2016-09 EN ISO 16148:2016 (E) 3 ForewordISO (the Internat

28、ional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has bee

29、n established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stand

30、ardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordan

31、ce with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

32、 any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsem

33、ent.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsibl

34、e for this document is ISO/TC 58, Gas cylinders, Subcommittee SC 4, Operational requirements for gas cylinders.This second edition cancels and replaces the first edition (ISO 16148:2006), which has been technically revised. The changes includea) expansion of the scope to include tubes of water capac

35、ity up to 3 000 l used for compressed and liquefied gases, andb) addition of procedures for ultrasonic examination (UT) follow-up during periodic inspection, as described in the new Annex A.DIN EN ISO 16148:2016-09 EN ISO 16148:2016 (E) 4 IntroductionIn recent years, new non-destructive examination

36、(NDE) techniques have been successfully introduced as an alternative to the conventional testing procedures of gas cylinders, tubes and other cylinders at the time of periodic inspection and testing.One of the alternative NDE methods for certain applications is acoustic emission examination (AT), wh

37、ich has proved to be an acceptable test method applied during periodic inspection and testing in some countries.The test method requires pressurization to a level greater than the normal filling pressure.The pressurization medium can be either gas or liquid.Acoustic emission (AE) measurements are us

38、ed to detect and locate emission sources. Other NDE methods are needed to evaluate the significance of AE detected sources. One of the alternative NDE methods used as a follow-up to AT is ultrasonic examination (UT), which has proved to be an acceptable testing method applied during periodic inspect

39、ion and testing. The purpose of this International Standard is to provide a procedure for locating, detecting and evaluating the relevance of AE indications such as those from longitudinally oriented crack-like discontinuities. The shear wave (angle beam) UT method is intended to be used immediately

40、 following AT to evaluate the significance of AE indications.This International Standard describes two methods of AT, defined as Method A and Method B, and a method of follow-up UT.With the agreement of the testing and certifying body approved by the competent authority of the country of approval, t

41、he hydraulic pressure test of cylinders and tubes can be replaced by an equivalent AT/UT Method A or B.This International Standard is intended to be used under a variety of national regulatory regimes, but has been written so that it is suitable for the application of Reference.1Attention is drawn t

42、o requirements in the specified relevant national regulations of the country (countries) where the cylinders are intended to be used that might override the requirements given in this International Standard. Where there is any conflict between this International Standard and any applicable regulatio

43、n, the regulation always takes precedence.DIN EN ISO 16148:2016-09 EN ISO 16148:2016 (E) 5 1 ScopeThis International Standard gives procedures for the use of acoustic emission examination (AT) and ultrasonic examination (UT) follow-up during the periodic inspection and testing of seamless steel cyli

44、nders and tubes with a water capacity of up to 3 000 l used for compressed and liquefied gases. This examination provides acoustic emission (AE) indications and locations that are evaluated by a secondary examination using UT for a possible flaw in the cylinder or tube. Methods other than UT for the

45、 secondary examination are not covered by this International Standard.This International Standard does not cover composite cylinders.CAUTION Some of the tests specified in this International Standard involve the use of processes which could lead to a hazardous situation.2 Normative referencesThe fol

46、lowing documents, in whole or in part, are normatively referenced in this document and are indispensable for is application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5577, Non-de

47、structive testing Ultrasonic inspection VocabularyISO 6406, Gas cylinders Seamless steel gas cylinders Periodic inspection and testingISO 9712, Non-destructive testing Qualification and certification of NDT personnelISO 12716, Non-destructive testing Acoustic emission inspection VocabularyISO/IEC 17

48、025, General requirements for the competence of testing and calibration laboratoriesEN 13477-1, Non-destructive testing Acoustic emission Equipment characterisation Part 1: Equipment descriptionEN 13477-2, Non-destructive testing Acoustic emission Equipment characterisation Part 2: Verification of operating characteristicASTM E1419, Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels using Acoustic EmissionASNT SNT-TC-1A, Recommended Practice for Personnel