DIN EN ISO 15750-1-2008 Packaging - Steel drums - Part 1 Removable head (open head) drums with a minimum total capacity of 208 l 210 l and 216 5 l (ISO 15750-1 2002) German version.pdf

《DIN EN ISO 15750-1-2008 Packaging - Steel drums - Part 1 Removable head (open head) drums with a minimum total capacity of 208 l 210 l and 216 5 l (ISO 15750-1 2002) German version.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 15750-1-2008 Packaging - Steel drums - Part 1 Removable head (open head) drums with a minimum total capacity of 208 l 210 l and 216 5 l (ISO 15750-1 2002) German version.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、September 2008DEUTSCHE NORM English price group 10No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55.140!$QfE“1466734w

2、ww.din.deDDIN EN ISO 15750-1Packaging Steel drums Part 1: Removable head (open head) drums with a minimum totalcapacity of 208 l, 210 l and 216,5 l (ISO 15750-1:2002)English version of DIN EN ISO 15750-1:2008-09Verpackung Stahlfsser Teil 1: Deckelfsser mit einem Gesamtvolumen von mindestens 208 l, 2

3、10 l und 216,5 l(ISO 15750-1:2002)Englische Fassung DIN EN ISO 15750-1:2008-09SupersedesDIN EN 209:2000-02www.beuth.deDocument comprises 13 pages DIN EN ISO 15750-1:2008-09 2 National foreword This standard has been prepared by Technical Committee ISO/TC 122 “Packaging” with TSE (Turkey) holding the

4、 secretariat. The secretariat is currently held by JISC (Japan) and ISIRI (Iran). This standard has been published in accordance with a decision taken by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France), Subcommittee SC 5 “Primary packaging and transport packaging” (Secretaria

5、t: BSI, United Kingdom) to adopt, without alteration, International Standard ISO 15750-1:2002 as European Standard EN ISO 15750-1:2008. The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Technical Committee NA 115-02-03 A

6、A Spund- und Deckelfsser. DIN EN ISO 15750 consists of the following parts, under the general title Packaging Steel drums: Part 1: Removable head (open head) drums with a minimum total capacity of 208 l, 210 l and 216,5 l Part 2: Non-removable head (tight head) drums with a minimum total capacity of

7、 212 l, 216,5 l and 230 l Part 3: Inserted flange-type closure systems The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 228-1:2000 DIN EN ISO 228-1:2003 ISO 15750-3 DIN EN ISO 15750-3 Amendments This standard differs from DIN EN 209:2000

8、-02 as follows: a) The specifications have been taken from DIN EN 209. b) The standard has been editorially revised. Previous editions DIN EN 209: 1988-07, 2000-02 DIN 6644-1: 1972-02, 1987-02 National Annex NA (informative) Bibliography DIN EN ISO 228-1, Pipe threads where pressure-tight joints are

9、 not made on the threads Part 1: Dimensions, tolerances and designation DIN EN ISO 15750-3, Packaging Steel drums Part 3: Inserted flange-type closure systems EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 15750-1June 2008ICS 55.140English VersionPackaging - Steel drums - Part 1: Removable he

10、ad (open head)drums with a minimum total capacity of 208 l, 210 l and 216,5 l(ISO 15750-1:2002)Emballages - Fts en acier - Partie 1: Fts ouverturetotale dune capacit totale minimale de 208 l, 210 l et216,5 l (ISO 15750-1:2002)Verpackung - Stahlfsser - Teil 1: Deckelfsser mit einemGesamtvolumen von m

11、indestens 208 l, 210 l und 216,5 l(ISO 15750-1:2002)This European Standard was approved by CEN on 16 May 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any altera

12、tion. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by transla

13、tionunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Gre

14、ece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement C

15、entre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15750-1:2008: E2 DIN EN ISO 15750-1:2008-09 EN ISO 15750-1:2008 (E) Contents Page Foreword3 1 Scope 5 2 Normative references 5 3 Term

16、s and definitions .5 4 Dimensions.6 5 Material .6 6 Construction.6 7 Finish 9 8 Designation 9 Annex A (normative) Capacity measurement method for removable head (open head) drums 10 A.1 Principle10 A.2 Apparatus .10 A.3 Procedure .10 A.3.1 Determination of the total capacity10 A.3.2 Determination of

17、 the brimful capacity .11 A.4 Expression of results 11 Foreword3 The text of ISO 15750-1:2002 has been prepared by Technical Committee ISO/TC 122 “Packaging” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 15750-1:2008 by Technical Committee CEN/TC 261 “

18、Packaging” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn at the latest by December

19、 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organ

20、izations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro

21、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 15750-1:2002 has been approved by CEN as a EN ISO 15750-1:2008 without any modification. EN ISO 15750-1:2008 (E) DIN EN ISO 15750-1:2008-09 IntroductionThroughout the world a large number

22、 of steel drum types with different dimensions and characteristics are beingused. The differences in location of the filling opening and outer dimensions result in differences in filling, handlingand transportation.This part of ISO 15750 gives uniform specifications for four main types of drums for

23、use in international trade andthe preferred target option is drum type A (see Table 1).It specifies the characteristics and dimensions of steel drums which are of importance for the exchangeability, anddoes not give detailed performance requirements and related test methods. The performance requirem

24、ents dependon the specific application.Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatoryrequirements which govern the transport of those goods in the countries concerned, including capseals/oversealsfitted in accordance with the certif

25、icate. Depending upon the mode of transport, this means meeting therequirements of: UN (United Nations): Recommendations on the transport of dangerous goods. Model regulations; ICAO (International Civil Aviation Organization): Technical Instructions for safe transport of dangerous goodsby air; IMO (

26、International Maritime Organization): International Maritime Dangerous Goods (IMDG) Code.This involves the certification and marking of the drums according to the regulations.4 DIN EN ISO 15750-1:2008-09 EN ISO 15750-1:2008 (E) 1 ScopeThis part of ISO 15750 specifies the characteristics and dimensio

27、ns of removable head (open head) drums,manufactured from steel sheet, having a total capacity of 208 l, 210 l and 216,5 l.It also specifies a method for measuring the total and brimful capacity.2 Normative referencesThe following normative documents contain provisions which, through reference in thi

28、s text, constitute provisions ofthis part of ISO 15750. For dated references, subsequent amendments to, or revisions of, any of these publicationsdo not apply. However, parties to agreements based on this part of ISO 15750 are encouraged to investigate thepossibility of applying the most recent edit

29、ions of the normative documents indicated below. For undatedreferences, the latest edition of the normative document referred to applies. Members of ISO and IEC maintainregisters of currently valid International Standards.ISO 228-1:2000, Pipe threads where pressure-tight joints are not made on the t

30、hreads Part 1: Dimensions,tolerances and designationISO 3573:1986, Hot-rolled carbon steel sheet of commercial and drawing qualitiesISO 3574:1986, Cold-reduced carbon steel sheet of commercial and drawing qualitiesISO 15750-3, Packaging Steel drums Part 3: Inserted flange-type closure systems3 Terms

31、 and definitionsFor the purposes of this part of ISO 15750, the following terms and definitions apply.3.1removable head (open head) drumOHcylindrical packaging made of steel, the bottom end of which is permanently fixed to the body and the top end canbe removed as a lid and closed by means of a clos

32、ing ringNOTE The top end may have additional openings for filling and venting.3.2round seamseam consisting of six or more layers of steel5 EN ISO 15750-1:2008 (E) DIN EN ISO 15750-1:2008-09 3.3nominal capacitycapacity, in litres, which by convention is used to represent a class of drums of similar b

33、rimful capacities3.4brimful capacityvolume of water, in litres, held by the drum when filled through the fitted filling orifice to the point of overflowing, thedrum being closed and having a lid fitted with closuresNOTE Annex A specifies the measuring method.3.5total capacityTCvolume of water, in li

34、tres, held by the drum when filled completely, i.e. following the removal of any air trapped inthe drum, the drum being closed and having a lid fitted with closuresNOTE Annex A specifies the measuring method.4 DimensionsThe dimensions of the drum shall be as shown in Figure 1 and detailed in Table 1

35、 for drum type A, B, C or D.The steel thickness shall be between 0,6 mm and 1,6 mm, with tolerances according to ISO 3573 or ISO 3574(normal tolerances).5 MaterialBody and ends shall be of steel sheet CR1 (commercial quality) for cold-reduced steel, according toISO 3574:1986, or of steel sheet HR1 (

36、commercial quality) for hot-rolled steel according to ISO 3573:1986. Steel ofhigher strength is permitted.Closure flanges shall be manufactured from metal, and closure plugs from metal or plastics material.6 Construction6.1 Body and heads shall be constructed of steel of adequate thickness in relati

37、on to the intended use.6.2 The longitudinal seam of the body shall be welded.6.3 The body and bottom end shall be permanently fixed by round seaming as shown in Figure 1, detail A, usinga non-hardening seaming compound, or other joining methods (e.g. welding).6.4 Two rolling hoops (beads) expanded o

38、r rolled into the body shall be located as shown in Figure 1.Constructions of rolling hoops other than those shown are allowed including a third rolling hoop (bead), orreplacement of the beads by small corrugations.NOTE The preferred drum type is the drum with two rolling hoops only.6.5 The removabl

39、e top end shall be fitted with a gasket of suitable material.6.6 The construction of the closing ring shall be such that the tightness of the drum is not jeopardized.6 DIN EN ISO 15750-1:2008-09 EN ISO 15750-1:2008 (E) Dimensions in millimetresaClosures (optional).bThird bead is optional.cDetail of

40、drum type B + D.Figure 1 Removable head (open head) drum7 EN ISO 15750-1:2008 (E) DIN EN ISO 15750-1:2008-09 Table 1 Dimensions of removable head (open head) steel drumsDimensions in millimetresDescriptionDrumType ADrumType BDrumType CDrumType DDimension(seeFigure 1)Total capacity210 lmin.216,5 lmin

41、.210 lmin.216,5 lmin.208 lmin.208 lmin.D1Internal diameter571,5 2 571,5 2 571,5 2 571,5 2 566 2 566 2D2External diameter over rolling hoops585 max. 585 max. 596 max. 596 max. 585 max. 585 max.D3Diameter over bottom chime585 max. 585 max. 593 max. 593 max. 585 max. 585 max.D4Diameter over closing rin

42、g585 maxa585 max.a610 max. 610 max. 585 max.a620 max.H1Total drum height878 5 888 5 878 5 888 5 890 5 890 5H5Height with cover off868 5 878 5 868 5 878 5 880 5 880 5h2Depth of top bbbbbbh3Clearance from floor4min. 4min. 4min. 4min. 4min. 4min.h4Distance between beads280 3 280 3 280 3 280 3 300 3 300

43、 3p1Centre-to-centre distance of closures ccccccp2Location of G2 (50 mm) closure tooutside body, measured approximately50 mm from the top72 372 372 372 394 394 3The total capacity shall be as indicated when measured in accordance with annex A.Closures are optional. If closures are fitted, the insert

44、ion of the closure with the G2 thread according to ISO 15750-3 shall be such that itscentreline is as close as possible to the vertical.NOTE 1 Of the four drum types shown, types A and C have the optimal outside dimensions required for stacking drums four abreast inISO containers as per ISO 668:1995

45、, Series 1 freight containers Classification, dimensions and ratings.NOTE 2 For types A and C, the diameter D4is achieved by modification of the top construction. The two approaches in use are as follows.a) Reduction of the drum whereby the closing system (curl, cover, closing ring) maintains the sa

46、me dimensions as in use for type B andtype D. The required inside diameter of the reduced top part of the drum is in this case approx. 545 mm for type A and 536 mm fortype C.b) Changing of the closing system (curl, cover and closing ring) so that, while maintaining the inside diameter at 571,5 mm fo

47、r type A and566 mm for type C, the total outside diameter is kept within 585 mm.aThe diameter over the closing ring shall normally be a maximum of 585 mm but may be slightly larger if measured over the lever sectionor bolt section of the ring.bIf the lid is fitted with closures, the depth of the top

48、 shall be such that the closures do not protrude above the closing ring.cFor the centre to centre distance of the closures the dimensions shall be: drum type A and B: 444 mm 6 mm or 451 mm 1 mm; drum type C and D: 400 mm 6mm.8 DIN EN ISO 15750-1:2008-09 EN ISO 15750-1:2008 (E) 6.7 If additional clos

49、ures are provided in the top end, the following applies.a) The closures shall be positioned in the top end, diametrically opposed as indicated in Figure 1.b) The nominal pitch diameter and pitch of the closures shall be as defined in ISO 228-1, threads G 3/4 and G 2.c) The closures should be as specified in ISO 15750-3, unless otherwise agreed between the purchaser andmanufacturer.d) Gaskets/washers or other sealing elements shall be used with the closures unless the fittings