DIN EN ISO 10748-2011 Footwear - Test method for slide fasteners - Slider locking strength (ISO 10748 2011) German version EN ISO 10748 2011《鞋类 拉链测试 自锁强度(ISO 10748-2011) 德文版本EN ISO.pdf

《DIN EN ISO 10748-2011 Footwear - Test method for slide fasteners - Slider locking strength (ISO 10748 2011) German version EN ISO 10748 2011《鞋类 拉链测试 自锁强度(ISO 10748-2011) 德文版本EN ISO.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 10748-2011 Footwear - Test method for slide fasteners - Slider locking strength (ISO 10748 2011) German version EN ISO 10748 2011《鞋类 拉链测试 自锁强度(ISO 10748-2011) 德文版本EN ISO.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、June 2011 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 61

2、.040; 61.060!$r=“1799326www.din.deDDIN EN ISO 10748Footwear Test method for slide fasteners Slider locking strength (ISO 10748:2011)English translation of DIN EN ISO 10748:2011-06Schuhe Prfverfahren fr Reiverschlsse Festigkeit der Schieberarretierung (ISO 10748:2011)Englische bersetzung von DIN EN I

3、SO 10748:2011-06Chaussures Mthode dessai pour les fermetures glissire Rsistance de blocage du curseur (ISO 10748:2011)Traduction anglaise de DIN EN ISO 10748:2011-06www.beuth.deDocument comprises 10 pages In case of doubt, the German-language original shall be considered authoritative.05.11 DIN EN I

4、SO 10748:2011-06 2 National foreword This standard has been prepared by Technical Committee CEN/TC 309 “Footwear” (Secretariat: AENOR, Spain) in collaboration with Technical Committee ISO/TC 216 “Footwear”. The responsible German body involved in its preparation was the Normenausschuss Materialprfun

5、g (Materials Testing Standards Committee), Working Committee NA 062-04-52 AA Schuhe. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 7500-1 DIN EN ISO 7500-1 ISO 19952 DIN EN ISO 19952 National Annex NA (informative) Bibliography DIN EN

6、 ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/ compression testing machines Verification and calibration of the force-measuring system DIN EN ISO 19952, Footwear Vocabulary EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10748 March 2011 IC

7、S 61.060 English Version Footwear - Test method for slide fasteners - Slider locking strength (ISO 10748:2011) Chaussures - Mthode dessai pour les fermetures glissire - Rsistance de blocage du curseur (ISO 10748:2011) Schuhe - Prfverfahren fr Reiverschlsse - Festigkeit der Schieberarretierung (ISO 1

8、0748:2011) This European Standard was approved by CEN on 31 December 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliog

9、raphical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsib

10、ility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece

11、, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management

12、 Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10748:2011: EContents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle5 5 Apparatus and mat

13、erials.5 6 Preparation of test specimens .6 7 Procedure .6 8 Test report 7 Bibliography 8 DIN EN ISO 10748:2011-06 EN ISO 10748:2011 (E) 2 Foreword This document (EN ISO 10748:2011) has been prepared by Technical Committee CEN/TC 309 “Footwear”, the secretariat of which is held by AENOR in collabora

14、tion with Technical Committee ISO/TC 216 “Footwear”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by Septembe

15、r 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards orga

16、nizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

17、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN ISO 10748:2011-06 EN ISO 10748:2011 (E) 3 1 Scope This International Standard specifies a test method to determine the locking strength of a slide fastener slider for footwear. The method is applicable to

18、all types of slide fastener that have a slider locking device. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document

19、 (including any amendments) applies. ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/ compression testing machines Verification and calibration of the force-measuring system ISO 19952, Footwear Vocabulary 3 Terms and definitions For the purposes of thi

20、s document, the terms and definitions given in ISO 19952 and the following apply. 3.1 slide fastener means of securing two flexible materials consisting of interlockable elements, each attached to one of the opposing edges of two tapes, and movable slider that spans the interlocking elements, which,

21、 when moved in one direction, causes the elements of one tape to interlock with the elements of the other tape and, when moved in the opposite direction, causes the elements to disengage See Figure 1. 3.2 tape fabric panel to support the other elements of the slide fastener 3.3 slider means of drawi

22、ng the two interlocking elements together or apart as it traverses the length of the chain 3.4 puller piece of plastic or metal attached to the slider as a means of manual grip for the user to operate 3.5 teeth individual element of the slide fastener which interlocks with an opposing element DIN EN

23、 ISO 10748:2011-06 EN ISO 10748:2011 (E) 4 Key 1 top stop 5 puller 2 tape 6 chain 3 elements (teeth) 7 bottom stop 4 slider Figure 1 Slider fastener 3.6 end stop top stop terminal component of the chains to prevent the slider from disengaging from the teeth and tape 3.7 locking device any component

24、that prevent unintended movement of the slider during use or wear 4 Principle The slider is locked on to the chain of the slide fastener and the locking device subjected to a tensile force applied at 180 to the locking device via the chain stringers. The force is increased until failure occurs. 5 Ap

25、paratus and materials 5.1 Tensile testing machine, with: a) a jaw separation rate of (100 10) mm/min; b) the capability of measuring forces up to 2 kN to an accuracy of better than 2 %, as specified by class 2 in ISO 7500-1; c) the facility to record the maximum force applied during the test. DIN EN

26、 ISO 10748:2011-06 EN ISO 10748:2011 (E) 5 6 Preparation of test specimens 6.1 A minimum of three slide fasteners shall be tested. 6.2 Condition the test specimens at 23 C and 50 % relative humidity (RH) for 24 h before testing, and carry out the test in this environment. 6.3 Set each test specimen

27、in the open position with the locking device locked into the chain about 30 mm from the top stops. 7 Procedure 7.1 Set the jaws of the tensile testing machine (5.1) (50 5) mm apart and secure the test specimen centrally in the jaws, such that the top of each stringer is clamped adjacent to the top s

28、top (see Figure 2). 7.2 Ensure that the locking mechanism remains in place throughout the test, operate the tensile testing machine to increase the force on the test specimen until the locking mechanism slips or the test specimen fails. Record the force at failure, F, in newtons, to the nearest 1 N.

29、 7.3 Record the type of failure as: slipping of locking mechanism; failure of test specimen. 7.4 Repeat the procedure in 7.1 to 7.3 for the remaining test specimens. 7.5 For each type of failure, record the number of test specimens exhibiting that type of failure and calculate the arithmetic mean of

30、 the corresponding values of F, recorded in 7.3, as the slider locking strength. Dimensions in millimetres Key 1 jaw 2 top stop 3 slider Figure 2 Slider locking test DIN EN ISO 10748:2011-06 EN ISO 10748:2011 (E) 6 8 Test report The test report shall include at least the following information: a) re

31、ference to this International Standard, i.e. ISO 10748:2010; b) full description of the sample (slide fastener) tested; c) date of testing; d) for each type of failure: 1) the number of test specimens exhibiting the type of failure, as recorded in 7.5; 2) the slider locking strength, as recorded in

32、7.5; e) any deviation(s) from this test method. DIN EN ISO 10748:2011-06 EN ISO 10748:2011 (E) 7 Bibliography 1 ISO 17709, Footwear Sampling location, preparation and duration of conditioning of samples and test pieces 2 ISO 18454, Footwear Standard atmospheres for conditioning and testing of footwear and components for footwear DIN EN ISO 10748:2011-06 EN ISO 10748:2011 (E) 8