DIN EN 16865-2016 Inland navigation vessels - Connections and assembled hoses for the transfer of potable water German version EN 16865 2016《内河航行用船舶 饮用水输送连接和组装软管 德文版本EN 16865-2016》.pdf

《DIN EN 16865-2016 Inland navigation vessels - Connections and assembled hoses for the transfer of potable water German version EN 16865 2016《内河航行用船舶 饮用水输送连接和组装软管 德文版本EN 16865-2016》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16865-2016 Inland navigation vessels - Connections and assembled hoses for the transfer of potable water German version EN 16865 2016《内河航行用船舶 饮用水输送连接和组装软管 德文版本EN 16865-2016》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、December 2016 English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 47.020.30; 47.060!%2“2599115www

2、.din.deDIN EN 16865Inland navigation vessels Connections and assembled hoses for the transfer of potable water;English version EN 16865:2016,English translation of DIN EN 16865:2016-12Fahrzeuge der Binnenschifffahrt Anschlsse und Schlauchleitungen fr das Bunkern von Trinkwasser;Englische Fassung EN

3、16865:2016,Englische bersetzung von DIN EN 16865:2016-12Bateaux de navigation intrieure Raccords et tuyaux flexibles pour le ravitaillement en eau potable;Version anglaise EN 16865:2016,Traduction anglaise de DIN EN 16865:2016-12www.beuth.deDocument comprises 18 pagesDTranslation by DIN-Sprachendien

4、st.In case of doubt, the German-language original shall be considered authoritative.12.16 DIN EN 16865:2016-12 2 A comma is used as the decimal marker. National foreword This document (EN 16865:2016) has been prepared by Technical Committee CEN/TC 15 “Inland navigation vessels” (Secretariat: DIN, Ge

5、rmany). The responsible German body involved in its preparation was DIN-Normenstelle Schiffs- und Meerestechnik (DIN Standards Committee Shipbuilding and Marine Technology), Working Committee NA 132-07-01 AA FA Binnenschifffahrt, Wasserfahrzeuge, Hafenanlagen (BWH) und NA 132-07 FB. The DIN Standard

6、s corresponding to the International Standards referred to in this document are as follows, whereby EN ISO Standards are only listed below if these have not been published as DIN EN ISO Standards with the same number: EN 22768 -1 DIN ISO 2768 -1 ISO 14726 DIN ISO 14726 National Annex NA (informative

7、) Bibliography DIN ISO 2768-1, General tolerances Tolerances for linear and angular dimensions without individual tolerance indications DIN ISO 14726, Shipbuilding and marine technology Identification colours for the content of piping systems EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1686

8、5 October 2016 ICS 47.020.30; 47.060 English Version Inland navigation vessels - Connections and assembled hoses for the transfer of potable water Bateaux de navigation intrieure - Raccords et tuyaux flexibles pour le ravitaillement en eau potable Fahrzeuge der Binnenschifffahrt - Anschlsse und Schl

9、auchleitungen fr das Bunkern von Trinkwasser This European Standard was approved by CEN on 12 June 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration

10、. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by t

11、ranslation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Fi

12、nland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZAT

13、ION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16865:2016 E2 Contents Page European foreword .

14、 4 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions 6 4 Technical requirements 7 4.1 General information . 7 4.2 Components . 7 4.2.1 General information . 7 4.2.2 Fixed connection 9 4.2.3 Pipe connector . 10 4.2.4 Dummy coupling . 11 4.2.5 Pipe . 11 4.2.6 Retrofitting

15、 connection . 11 4.3 Dimensions 13 4.4 Connection configuration 13 5 Materials 14 5.1 General information 14 5.2 Pipe with thread connection and connector . 14 5.3 Pipe . 14 6 Instructions for use 14 7 Description 14 7.1 Supply side connection for storing potable water 14 7.2 Pipeline for storing po

16、table water . 14 7.3 Consumer side connection for storing potable water . 14 7.4 Retrofitting connection . 15 8 Labelling . 15 8.1 Pipe . 15 8.2 Connection for storing potable water . 15 Bibliography . 16 Figures Figure 1 Overview of potable water transfer, here the example has a fixed connection on

17、 the supply side, a pipeline and a fixed coupling on the consumer side 8 Figure 2 Overview of potable water transfer, here the example has a fixed pipeline connected on the supply side and a retrofitting coupling on the consumer side 9 Figure 3 Fixed connection 10 Figure 4 Pipe connection 11 Figure

18、5 Retrofitting connection . 12 Figure 6 Plate for labelling the potable water connection . 15 EN 16865:2016 (E) DIN EN 16865:2016-12 3 Tables Table 1 Parts list 13 Table 2 Dimensions for reducing couplings or brackets (item 9) . 13 EN 16865:2016 (E) DIN EN 16865:2016-12 4 European foreword This docu

19、ment (EN 16865:2016) has been prepared by Technical Committee CEN/TC 15, “Inland navigation vessels“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, by April 2017 at the l

20、atest, and any conflicting national standards shall be withdrawn by April 2017 at the latest. It should be noted that some elements of this document may be subject to patent rights. CEN and/or CENELEC shall not be responsible for identifying any or all such patent rights. According to the CEN-CENELE

21、C Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icel

22、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. EN 16865:2016 (E) DIN EN 16865:2016-12 5 Introduction This European standard has been developed to specify hygieni

23、cally perfect, standard pipelines and connections for the transfer and receipt of potable water on the supply side (bunker boats, onshore plant or similar) and the consumer side (inland navigation vessel). The connection consists of a pipe, a rapid coupling device both on the supply and consumer sid

24、e with appropriate dummy couplings. This will allow simple handling and secure transfer of potable water. Using this standard will prevent unsuitable pipes being used on the supply side and dirt getting into the potable water bunker on the consumer side by using pipes without couplings in openings t

25、hat are level with the deck. Dirt, micro-organisms and insects are prevented from penetrating by using dummy couplings on both sides. EN 16865:2016 (E) DIN EN 16865:2016-12 6 1 Scope This European standard specifies the design, dimensions and technical requirements for connections and pipelines for

26、storing potable water for inland navigation vessels. These are: a fixed connection on the supply side; pipeline; a fixed connection on the consumer side; a connection for retrofitting inland navigation vessels that have a closure device level with the deck (internal pipe thread pursuant to EN ISO 22

27、8-1), consisting of a connecting part with a threaded connection and fixed coupling. Necessary measures to prevent electrostatic charge and overfilling are not governed by the standard. National regulations apply to drinking water supply plants. The requirements of this European standard supplement

28、these regulations. 2 Normative references The following documents cited in whole or in part in this document are required for the application of this document. For dated references, only the edition referred to applies. For undated references, the latest version of the document referred to applies (

29、including all amendments). DIN 14302, PN 16 aluminium alloy C pressure coupling DIN 14307-1, PN 16 aluminium alloy C fixed coupling with sealing ring for pressure operation DIN 14311, PN 16 aluminium alloy C dummy coupling for pressure and suction operation EN 10220, Seamless and welded steel tubes

30、Dimensions and masses per unit length EN 22768-1, General Tolerances Part 1: Tolerences for linear and angular dimensions without records of individual tolerances (ISO 2768-1:1989) EN ISO 228-1, Pipe threads where pressure-tight connections are not made on the thread Part 1: Dimensions, tolerances a

31、nd designations (ISO 228-1) EN ISO 9093-1, Small craft Seacocks and through-hull fittings Part 1: Metallic parts (ISO 9093-1) ISO 14726, Ships and marine technology Identification colours for the content of piping systems 3 Terms and definitions The following terms apply to the application of this d

32、ocument. EN 16865:2016 (E) DIN EN 16865:2016-12 7 3.1 potable water Water for human consumption as specified in Council Directive 98/83/EG (see 8) SOURCE: EN 13443-2:2005+A1:2007, 3.12 3.2 pipeline Pipe with a pipe connection on both sides or with a pipe connection on one side and a fixed connection

33、 on the other side 3.3 pipe connector Pipeline fitting consisting of a pipe clamp, a pipe coupling and a dummy coupling 3.4 fixed connection A permanently installed fitting consisting of a threaded pipe connection, fixed coupling and dummy coupling 4 Technical requirements 4.1 General information Ge

34、neral tolerances: ISO 2768 c The requirements relate to the design, dimensions and configuration of the connections. 4.2 Components 4.2.1 General information The position of the connection and the dimensions and specifications as set out under Paragraph 4 - Paragraph 7 shall be observed for the conn

35、ection. On the supply side, there are the following versions: Fixed connection to connect a pipeline; Permanently connected pipeline. On the consumer side there are the following versions: Fixed connection; Retrofitting connection. The overviews in Figure 1 and Figure 2 provide examples of connectio

36、ns for storing potable water. EN 16865:2016 (E) DIN EN 16865:2016-12 8 Key a Fixed connection on the supply side. b Pipeline. c Fixed connection on the consumer side. Figure 1 Overview of potable water transfer, here the example has a fixed connection on the supply side, a pipeline and a fixed coupl

37、ing on the consumer side Key a Permanently connected pipeline on the supply side. b Retrofitting connector. EN 16865:2016 (E) DIN EN 16865:2016-12 9 Figure 2 Overview of potable water transfer, here the example has a fixed pipeline connected on the supply side and a retrofitting coupling on the cons

38、umer side 4.2.2 Fixed connection 4.2.2.1 General information The fixed connection, see Figure 3, shall consist of a threaded pipe connection, a C coupling with dimensions as per DIN 14307-1 as a fixed coupling and a dummy coupling. 4.2.2.2 Fixed connection on the supply side The C coupling on the su

39、pply side, 4.2.2.1, shall be permanently connected to the threaded pipe connection. EN 16865:2016 (E) DIN EN 16865:2016-12 10 4.2.2.3 Fixed connection on the consumer side The C coupling on the consumer side, 4.2.2.1, shall be permanently connected to a threaded pipe connection. The pipe shall be fi

40、tted with an ISO 228 G 2 A pipe thread 20 mm long (DN 50). The pipe connection shall be welded firmly to the superstructure, the deck or the pipeline system and in such a way that its end is at least 300 mm above the deck. The C coupling shall be permanently attached to the pipe connection. Dimensio

41、ns in millimetres Key Item no. see parts list Table 1 Figure 3 Fixed connection 4.2.3 Pipe connector The pipe connector, see Figure 4, shall consist of a C coupling with dimensions as per DIN 14302, that is attached to the pipe by a pipe clamp as per 4.2.5 and a dummy coupling. EN 16865:2016 (E) DIN

42、 EN 16865:2016-12 11 Key Item no. see parts list Table 1 Figure 4 Pipe connection 4.2.4 Dummy coupling Each fixed and pipe coupling shall be fitted with a dummy coupling with dimensions as per DIN 14311 that shall be attached to the relevant coupling so that it cannot be detached, e.g. with a chain

43、and an S hook. It shall be possible to lock dummy couplings that are not secured against unauthorised access in the closed position. 4.2.5 Pipe The pipe shall meet the requirements set out in 5.3. 4.2.6 Retrofitting connection The fixed coupling on the consumer side on inland navigation vessels that

44、 have a screw connection for receiving potable water shall be connected using a retrofitting connection, see Figure 5. The connection consists of: a C coupling with dimensions as per DIN 14307-1; a connecting part consisting of a pipe of at least 300 mm long with 20 mm long ISO 228 G 2 A pipe thread

45、s on both sides (DN 50); a dummy coupling if necessary, a reducing coupling or a reducing bracket. The connector shall be firmly welded or cemented to the screw connection. EN 16865:2016 (E) DIN EN 16865:2016-12 12 Designs: Design A: No reducing coupling Deck closure complies with pipe thread ISO 22

46、8 G 2 A; Design B: With reducing coupling Deck closure does not comply with pipe thread ISO 228 G 2 A; Design C: With reducing bracket for special connections, e.g. for connection running horizontally from the deck superstructure. Dimensions in millimetres Key Item no. see parts list Table 1 Figure

47、5 Retrofitting connection EN 16865:2016 (E) DIN EN 16865:2016-12 13 Table 1 Parts list Item no. Designation Picture Remarks 1 Pipe 4 See 4.2.5 2 Pipe clamp 4 As per EN ISO 9093-1 3 Pipe coupling 4 With dimensions as per DIN 14302 4 Dummy coupling 3, 4, 5 With dimensions as per DIN 14311 5 Undetachab

48、le connection 3, 4, 5 Connected permanently to items 3 and 4, e.g. with a chain and S hook. 6 Fixed coupling 3, 5 With dimensions as per DIN 14307-1 7 Pipe with thread connection 3 Pipe thread ISO 228 G 2 A (l = 20 mm) Pipe as per EN 10220 or equivalent 8 Connector 5 Pipe thread on both sides ISO 22

49、8 G 2 A (l = 20 mm) Pipe as per EN 10220 or equivalent (l = 300 mm) 9 Reducing coupling or reducing bracket 5 Not required with a deck closure with a nominal width as per DN 50 4.3 Dimensions The nominal size for the coupling is 52 = C. Dimensions for reducing couplings or brackets are set out in Table 2. Table 2 Dimensions for reducing couplings or brackets (item 9) Nominal deck closure size Pipe thread a