DIN EN 16722-2015 Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends German version EN 16722 2015《工业阀 螺纹连接端阀门的端到端和中心到端面尺寸 德文版本EN 16722-2015》.pdf

《DIN EN 16722-2015 Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends German version EN 16722 2015《工业阀 螺纹连接端阀门的端到端和中心到端面尺寸 德文版本EN 16722-2015》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16722-2015 Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends German version EN 16722 2015《工业阀 螺纹连接端阀门的端到端和中心到端面尺寸 德文版本EN 16722-2015》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、December 2015 English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.060.01!%IU“2389350www.din.de

2、DIN EN 16722Industrial valves End-to-end and centre-to-end dimensions for valves with threaded ends;English version EN 16722:2015,English translation of DIN EN 16722:2015-12Industriearmaturen Baulngen fr Armaturen mit Innengewinde-Anschluss;Englische Fassung EN 16722:2015,Englische bersetzung von DI

3、N EN 16722:2015-12Robinetterie industrielle Dimensions extrmit extrmit et axe extrmit pour les appareils de robinetterie embouts filets;Version anglaise EN 16722:2015,Traduction anglaise de DIN EN 16722:2015-12SupersedesDIN 3202-4:1982-04www.beuth.deDocument comprises 21 pagesDTranslation by DIN-Spr

4、achendienst.In case of doubt, the German-language original shall be considered authoritative.11.15 DIN EN 16722:2015-12 2 A comma is used as the decimal marker. National foreword This document (EN 16722:2015) has been prepared by Technical Committee CEN/TC 69 “Industrial valves” (Secretariat: AFNOR,

5、 France). The responsible German body involved in its preparation was DIN-Normenausschuss Armaturen (DIN Standards Committee Valves), Working Committee NA 003-01-01 AA Grundnormen. Amendments This standard differs from DIN 3202-4:1982-04 as follows: a) the standard has been adopted at European level

6、 with a new standard number; b) the scope has been rendered more precise and now also includes PN and Class designated sizes; c) Clause 2 “Normative references” has been updated; d) Clause 3 “Terms and definitions” has been added; e) Figure 1 c) “Three-way valve” has been included; f) the designatio

7、n has been dropped; g) basic series X1 to X24 have been introduced; h) dimensions of gate valves, ball valves, globe valves and lift check valves, globe control valves and automatic steam traps are now given in separate Tables; i) a Table giving tolerances has been included (Table 2); j) Annex A (in

8、formative) “Relationship between DN (nominal size) and internal thread” has been included; k) Annex B (informative) “Origin of basic series” has been included; l) Annex C (informative) “Relationship between DN (nominal size) and nominal pipe size” has been included; m) some clauses have been renumbe

9、red; n) the standard has been editorially revised. Previous editions DIN 3202-4: 1978-04, 1982-04 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16722 September 2015 ICS 23.060.01 English Version Industrial valves - End-to-end and centre-to-end dimensions for valves with threaded ends Robinett

10、erie industrielle - Dimensions extrmit extrmit et axe extrmit pour les appareils de robinetterie embouts filets Industriearmaturen - Baulngen fr Armaturen mit Innengewinde-Anschluss This European Standard was approved by CEN on 15 August 2015. CEN members are bound to comply with the CEN/CENELEC Int

11、ernal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to an

12、y CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official v

13、ersions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

14、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploit

15、ation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16722:2015 EEN 16722:2015 (E) 2 Contents PageEuropean foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Dimensions and tolerances . 6 4.1 Basic series 6 4.2 Toleranc

16、es . 7 Annex A (informative) Relationship between DN (nominal size) and internal thread 16 Annex B (informative) Origin of basic series 17 Annex C (informative) Relationship between DN (nominal size) and nominal pipe size (NPS) . 18 Bibliography . 19 DIN EN 16722:2015-12 EN 16722:2015 (E) 3 European

17、 foreword This document (EN 16722:2015) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the lat

18、est by March 2016, and conflicting national standards shall be withdrawn at the latest by March 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such

19、 patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedo

20、nia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16722:2015-12 EN 16722:2015 (E) 4 Introduction The basic series

21、given in this European Standard are taken from the original series shown in Annex B. Changes made to the original series will not be automatically incorporated into this European Standard. DIN EN 16722:2015-12 EN 16722:2015 (E) 5 1 Scope This European Standard specifies the end-to-end and centre-to-

22、end dimensions for valves with threaded ends with connecting dimensions in compliance with EN ISO 228-1 or EN 10226-1, used in PN and Class designated piping systems. The range of PN is: PN 10; PN 16; PN 25; PN 40; PN 63; PN 100; PN 160; PN 250; PN 320; PN 400. The range of Class is: Class 150, Clas

23、s 300, Class 600, Class 900, Class 1 500, Class 2 500. The range of nominal size is: DN 4; DN 6; DN 8; DN 10; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100. NOTE 1 See Annex C for the relationship between nominal size (DN) and nominal pipe size (NPS). NOTE 2 Valves having screwed en

24、d profiles different from those specified in EN ISO 228-1 or EN 102261, may use the same dimensions than those specified in Table 1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated r

25、eferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 736-1:1995, Valves Terminology Part 1: Definition of types of valves EN 736-2:1997, Valves Terminology Part 2: Definition of components of valves EN

26、 736-3:2008, Valves Terminology Part 3: Definition of terms 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 736-1:1995, EN 736-2:1997 and EN 736-3:2008 and the following apply. 3.1 end-to-end dimensions (ETE) (straight pattern valves) distance express

27、ed between the ends of the body for straight and oblique pattern valves 3.2 centre-to-end dimensions (CTE) (angle pattern valves) distance expressed between one of the ends of the body and the centre of the body for angle pattern valves 3.3 end-to-end and centre-to-end dimensions (ETE+CTE) (three-wa

28、y valves) distance expressed between the ends of the body (ETE) in the run and distance expressed between the end of the body in the branch and the centre of the body (CTE) DIN EN 16722:2015-12 EN 16722:2015 (E) 6 a) Straight and oblique pattern valve b) Angle pattern valve c) Three-way valve Key Fi

29、gure 1 a) ETE with ETE = l Figure 1 b) CTE with CTE = l Figure 1 c) ETE+CTE with ETE = l and CTE = l / 2 Figure 1 ETE and CTE dimensions 4 Dimensions and tolerances 4.1 Basic series The basic series of l for ETE and CTE dimensions are given in Table 1. For each type of valve, the basic series to be

30、taken into consideration shall be in accordance with Tables 3 to 7. Other dimensions are subject of agreement between manufacturer and purchaser. DIN EN 16722:2015-12 EN 16722:2015 (E) 7 NOTE 1 Table 1 gives complete series. In Tables 3 to 7 the columns of series may be reduced. NOTE 2 For certain s

31、izes/types of valves, alternative dimensions are permitted and are specified in Tables 3 to 7. 4.2 Tolerances Tolerances on ETE and CTE dimensions shall be in accordance with Table 2. DIN EN 16722:2015-12 EN 16722:2015 (E) 8 Table 1 Dimensions l of basic series Dimensions in millimetres DN Basic ser

32、ies M2 M3 M4 M5 X1 X2 X3 X4 X5 X6 X7 X8 X9 X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X20 4 50 70 50 69 69 69 6 50 70 50 69 69 69 85 8 55 70 55 70 65 78 69 69 85 55 67 75 10 70 60 75 55 95 70 65 78 55 73 73 72 85 55 67 75 15 85 75 85 65 95 49 200 70 65 90 65 117 104 84 95 65 75 90 20 100 80 95 75 95 49

33、 200 80 65 95 80 117 104 96 97 95 100 95 70 90 105 25 115 90 105 90 95 61 200 90 139 104 113 113 113 120 110 95 65 80 85 105 120 32 130 110 120 95 95 61 200 186 110 115 110 120 130 65 80 95 120 40 150 120 130 100 130 72 255 186 120 135 130 140 145 165 70 87 105 135 50 180 140 150 112 230 72 255 209

34、140 140 140 150 160 165 70 91 125 155 65 185 185 132 167 190 80 205 205 160 192 205 100 240 240 180 230 DIN EN 16722:2015-12 EN 16722:2015 (E) 9 Table 1 (continued) Dimensions in millimetres DN Basic series X21 X22 X23 X24 X25 X26 X27 X28 X29 X30 4 6 8 70 72 42 10 70 72 75 49 60 59 83 105 15 75 82 7

35、5 85 56 65 74 90 90 114 20 85 92 75 100 61 78 80 97 100 125 25 102 102 75 115 69 92 91 110 115 142 32 118 118 130 77 105 110 124 134 160 40 125 134 150 81 120 120 130 150 170 50 149 144 180 95 145 141 155 168 200 65 170 112 80 220 122 100 160 DIN EN 16722:2015-12 EN 16722:2015 (E) 10 Table 2 Toleran

36、ces Dimensions in millimetres Dimension ETE or CTE aTolerance above up to and including 0 250 2 250 500 3 500 800 4 800 1 000 5 1 000 1 600 6 1 600 2 500 8 aDimensions ETE or CTE in accordance with Figure 1. DIN EN 16722:2015-12 EN 16722:2015 (E) 11 Table 3 Gate valves PN/Class ETE series CTE series

37、 M2 M4 X13 X14 X16aX17 X25 X26 X27 X28 X29 X30 PN 10 to PN 16 x x x x x x x x x x x x PN 25 to PN 40 PN 63 to PN 100 PN 160 PN 250 to PN 320 PN 400 Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500 aThe dimensions in column X16 of Table 1 refer to the horizontal dimensions of a vertica

38、l gate valve type. DIN EN 16722:2015-12 EN 16722:2015 (E) 12 Table 4 Ball valves PN/Class ETE series M2 M4 X10 X11 X12 X13 X14 X18 aX19 aX20 aX21 aX22 aX24 X25 X26 X27 X28 X29 X30 PN 10 to PN 16 x x x x x x x x x x x x x x x x x X PN 25 to PN 40 x x x x x x x x x x x x x x x x x x x PN 63 to PN 100

39、x x x x x x x x x x PN 160 x x x x x x PN 250 to PN 320 x x x x x x PN 400 x x x x x Class 150 Class 300 Class 600 Class 900 Class 1 500 Class 2 500 aAdditional ETE+CTE series for three-way valves DIN EN 16722:2015-12 EN 16722:2015 (E) 13 Table 5 Globe valves and lift check valves; straight and obli

40、que patterns PN/Class ETE series X1 X2 X8 X9 X25 X26 X27 X28 X29 X30 M3 M4 M5 PN 10 to PN 16 x x x x x x x x x x x x x PN 25 to PN 40 x x x x x x x x x x x x PN 63 to PN 100 PN 160 PN 250 to PN 320 PN 400 Class 150 x x x x x x x x x x x x x Class 300 x x x x x x Class 600 Class 900 Class 1 500 Class

41、 2 500 DIN EN 16722:2015-12 EN 16722:2015 (E) 14 Table 6 Globe control valves; straight pattern PN/Class ETE series X8 M3 M4 M5 PN 10 to PN 16 x x x x PN 25 to PN 40 x x x x PN 63 to PN 100 PN 160 PN 250 to PN 320 PN 400 Class 150 x x x x Class 300 x x x x Class 600 Class 900 Class 1 500 Class 2 500

42、 DIN EN 16722:2015-12 EN 16722:2015 (E) 15 Table 7 Automatic steam traps PN/Class ETE series X1 X2 X3 X4 X5 X6 X7 X8 X9 X15 X23 M3 M4 M5 PN 10 to PN 16 x x x x x x x x x x x x x x PN 25 to PN 40 x x x x x x x x x x x x x PN 63 to PN 100 x x x PN 160 PN 250 to PN 320 PN 400 Class 150 x x x x x x x x

43、x x x x x x Class 300 x x x x x x x x x x x x x Class 600 x x x Class 900 Class 1 500 Class 2 500 DIN EN 16722:2015-12 EN 16722:2015 (E) 16 Annex A (informative) Relationship between DN (nominal size) and internal thread For the relationship between DN and internal thread, see Table A.1. Table A.1 R

44、elationship between DN and internal thread DN EN 102261 EN ISO 228-1 ASME B1.20.1 6 Rp G NPT 8 Rp G NPT 10 Rp G NPT 15 Rp G NPT 20 Rp G NPT 25 Rp 1 G 1 NPT 1 32 Rp 1 G 1 NPT 1 40 Rp 1 G 1 NPT 1 50 Rp 2 G 2 NPT 2 65 Rp 2 G 2 NPT 2 80 Rp 3 G 3 NPT 3 100 Rp 4 G 4 NPT 4 DIN EN 16722:2015-12 EN 16722:2015 (E) 17 Annex B (informative) Origin of basic series For origins of basic series,