DIN EN 16434-2014 Internal blinds - Protection from strangulation hazards - Requirements and test methods for safety devices German version EN 16434 2014《内部窗帘 防止勒束危险的保护 安全装置要求和试验方法.pdf

《DIN EN 16434-2014 Internal blinds - Protection from strangulation hazards - Requirements and test methods for safety devices German version EN 16434 2014《内部窗帘 防止勒束危险的保护 安全装置要求和试验方法.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16434-2014 Internal blinds - Protection from strangulation hazards - Requirements and test methods for safety devices German version EN 16434 2014《内部窗帘 防止勒束危险的保护 安全装置要求和试验方法.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、June 2014 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 9

2、1.060.50!%2b“2156398www.din.deDDIN EN 16434Internal blinds Protection from strangulation hazards Requirements and test methods for safety devices;English version EN 16434:2014,English translation of DIN EN 16434:2014-06Innere Abschlsse Schutz vor Strangulationsgefahren Anforderungen und Prfverfahren

3、 fr Sicherheitseinrichtungen;Englische Fassung EN 16434:2014,Englische bersetzung von DIN EN 16434:2014-06Stores intrieurs Protection contre les risques de strangulation Exigences et mthodes dessai pour les dispositifs de scurit;Version anglaise EN 16434:2014,Traduction anglaise de DIN EN 16434:2014

4、-06www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 20 pages 05.14 DIN EN 16434:2014-06 2 A comma is used as the decimal marker. National foreword This document (EN 16434:2014) has been prepared by Technical Committee CEN/TC 33 “Doors, w

5、indows, shutters, building hardware and curtain walling” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-09-01 AA Tren, Tore, Fenster, Ab-schlsse, Bau

6、beschlge und Vorhangfassaden. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16434 February 2014 ICS 91.060.50 English Version Internal blinds - Protection from strangulation hazards - Requirements and test methods for safety devices Stores intrieurs - Protection contre les risques de strangul

7、ation - Exigences et mthodes dessai pour les dispositifs de scurit Innere Abschlsse - Schutz vor Strangulationsgefahren - Anforderungen und Prfverfahren fr Sicherheitseinrichtungen This European Standard was approved by CEN on 26 October 2013. CEN members are bound to comply with the CEN/CENELEC Int

8、ernal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to an

9、y CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official v

10、ersions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

11、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploi

12、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16434:2014 EEN 16434:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 General 4 5 Artificial ageing 5 5.1 Exposure to UV 5 5.2 Mechanical endurance .5 5.3 E

13、ffect of temperature .5 6 Tensioning device5 6.1 General 5 6.2 Test methods .7 6.3 Requirements .8 7 Breakaway device 8 7.1 General 8 7.2 Test method .8 7.3 Requirements 11 8 Accumulation device 11 8.1 General . 11 8.2 Test method 11 8.3 Requirements 11 9 Non tangling device 11 9.1 General . 11 9.2

14、Test method 12 9.3 Requirements 12 10 Inner cord stop 12 10.1 General . 12 10.2 Test method 12 10.3 Requirements 13 11 Additional requirements 13 11.1 General . 13 11.2 Release of small components . 13 11.3 Impact resistance 14 12 Information and instruction for installation, use and maintenance 14

15、12.1 General . 14 12.2 Information 14 12.3 Instructions (for retrofitting purpose only) . 15 12.4 Marking . 16 13 Factory Production Control (FPC) 16 Annex A (informative) Tests to be carried out on safety devices . 17 Bibliography . 18 DIN EN 16434:2014-06 EN 16434:2014 (E) 3 Foreword This document

16、 (EN 16434:2014) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by

17、endorsement, at the latest by August 2014, and conflicting national standards shall be withdrawn at the latest by August 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for id

18、entifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This document is part of a series of standards dealing with blinds and shutters for buildings as defined in EN 12216. It is the in

19、tention that safety devices used in EN 13120 conform to EN 16434 for component testing and EN 16433 for functionality. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, B

20、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

21、 Turkey and the United Kingdom. DINEN 16434:2014-06EN 16434:2014 (E) 4 1 Scope This European Standard specifies requirements and test methods for safety devices to be used for protection from strangulation in internal blinds as specified in EN 13120 and insect screens as specified in EN 13561. These

22、 devices might be fitted to internal blinds and insect screens at the time of manufacture or for retrofitting. This European Standard applies to any design of device including the following: tensioning devices; breakaway devices; accumulation devices; non tangling devices; inner cord stops. Although

23、 at the time this standard has been published, no product standard exists for draperies, requirements and test methods specified in the present standard may be applied to safety devices used in such products. For clarification purpose, the term “internal blinds” used in the present standard should m

24、ean “internal blinds and insect screens”. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of th

25、e referenced document (including any amendments) applies. EN 12216, Shutters, external blinds, internal blinds - Terminology, glossary and definitions EN 13120, Internal blinds - Performance requirements including safety EN 13561, External blinds - Performance requirements including safety EN 14201,

26、 Blinds and shutters - Resistance to repeated operations (mechanical endurance) - Methods of testing EN 71-1, Safety of toys - Part 1: Mechanical and physical properties EN ISO 4892-2, Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2) EN ISO 4892-3, Pl

27、astics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12216, EN 13561 and EN 13120 apply. 4 General In the testing of safety devices, all related parts asso

28、ciated with the protection from strangulation shall be included. DIN EN 16434:2014-06 EN 16434:2014 (E) 5 For example, a breakaway device for an operating ball-chain should cover the ball-chain and the connector if the connector is dependent on the ball diameter. If an inner cord breakaway device is

29、 dependent on the type of fabric used in the internal blind then the fabric should also be considered as a part of the safety device. The number of samples tested shall be representative of the production run. Testing shall be repeated during the production to ensure that performances of devices are

30、 maintained. Testing shall be repeated whenever a change occurs in the design, in the composition, in the raw material or in the supplier of the raw material, or in the method of production. NOTE Guidance on sampling procedures can be found in ISO 2859-1. Although weights are used in the figures ill

31、ustrating test methods, any other mechanical, hydraulic or pneumatic equipment may be used. All weights and forces shall be applied with a tolerance of 1 %. Unless specified otherwise, all tests defined in this standard shall be performed at 23 C 5 C. Annex A presents a summary of the tests to be ca

32、rried out on safety devices. In the context of this standard, the term “cord(s)” used shall mean “cord(s), chain(s), ball-chain(s), tape(s) and similar”. 5 Artificial ageing 5.1 Exposure to UV Before testing the safety devices, they shall be subjected to the cycle N6 according to EN ISO 4892-2 or th

33、e cycle N5 according to EN ISO 4892-3 for 500 h. 5.2 Mechanical endurance The mechanical endurance test is intended to reproduce the operating cycles of internal blinds. Before testing the safety devices, they shall be submitted to the following endurance test: a mechanical endurance test shall be c

34、arried out either according to EN 14201 on a representative internal blind or using a mechanical test equipment reproducing the load conditions of the representative internal blind. 5 000 cycles of extension/retraction shall be considered. The internal blind considered for the test shall be the maxi

35、mum size for which the safety device is intended. 5.3 Effect of temperature Before testing the safety devices, they shall be submitted to the following temperature conditions: Low temperature: the safety devices shall be submitted to conditioning at an air temperature of 5 C 3 C for a minimum of 4 h

36、. High temperature: the safety devices shall be submitted to conditioning at an air temperature of 60 C 3 C for a minimum of 4 h. The relevant tests of Clauses 6 to 11 shall then start at 23 C 5 C within 15 min. 6 Tensioning device 6.1 General This clause applies to safety devices intended to mainta

37、in continuous cord(s) forming a loop under tension and secured to a fixed surface (e.g. window frame, wall). DIN EN 16434:2014-06 EN 16434:2014(E)6 The test shall be carried out on the smallest and the largest diameter of cord(s) for which the tensioning device is designed. The test shall be carried

38、 out on sample(s) as defined in Clause 4: in their original condition, that have been exposed to UV as specified in 5.1, that have been subjected to the mechanical endurance test as specified in 5.2, that have been subjected to the effect of temperature as specified in 5.3 (at low temperature and at

39、 high temperature). Where a tensioning device is designed to accept more than one cord, each cord shall be tested separately. It shall be verified that the fixed retaining device maintaining the cord(s) under tension shall not crack or fracture under the application of a horizontal load applied in t

40、he middle of the cord. In addition, it shall be verified that the cord is retained within the device when the device is fixed 10 mm higher than its intended position. The control mechanism shall be made of a pulley of 50 mm diameter. The length of the pull cord shall be 1 m (see Figure 1). Key 1 pul

41、l cord(s) 2 pulley 3 retaining device Figure 1 Principle of the test of tensioning device DINEN 16434:2014-06EN 16434:2014 (E) 7 6.2 Test methods 6.2.1 Resistance of the retaining device The tensioning device shall be installed according to the installation instructions of the manufacturer. The reta

42、ining device shall be installed at the maximum distance possible from the pulley (original position). The distance between the two strands of the loop shall be measured at the point of exit from the tensioning device (see Figure 2). Key 1 distance between the two strands Figure 2 Measurement of the

43、distance between the two strands A horizontal force shall be applied in the plane and at mid-point of the height of the loop (see Figure 1) in a progressive way over a period of maximum 5 s until the load defined in 6.3 is applied to one cord. The load shall be then maintained for 10 s. The test sha

44、ll be carried out with the load defined in 6.3. The test shall be repeated with the force being applied in the direction perpendicular to the plane of the cord. 6.2.2 Retention of cords The retaining device shall be installed at 10 mm above its original position (see 6.2.1). The cord shall then be p

45、ulled with the force defined in 6.3 in all possible directions. DINEN 16434:2014-06EN 16434:2014 (E) 8 6.3 Requirements The distance between the two strands of the loop shall be less than 50 mm at the point of exit from the tensioning device. When tested according to 6.2.1, no part of the fixed tens

46、ioning device shall crack or fracture under the application of a load of 60 N to the pull cord(s). The fixed tensioning device shall continue to function as intended. When tested according to 6.2.2, the cord shall remain in the retaining device when pulled with a force of 60 N in all possible direct

47、ions. 7 Breakaway device 7.1 General This clause applies to device(s) intended to connect: Case N1: two ends of the same cord, Case N2: several cords together at any point below the headrail, or Case N3: a cord to a curtain, and to break away under the application of a load. As these devices are mad

48、e of minimum two parts that separate under a specific load, all these parts shall be considered during the tests. As a consequence, these devices shall be considered as a whole and cannot be used separately. This test shall be carried out on sample(s) as defined in Clause 4: in their original condition, that have been exposed to UV as specified in 5.1, that have been subjected to the following mechanical endurance test: The breakaway element shall be engaged and disengaged 20