DIN EN 16261-3-2013 Pyrotechnic articles - Fireworks Category 4 - Part 3 Test methods German version EN 16261-3 2012《烟火制品 4类烟火 第3部分 试验方法 德文版本EN 16261-3-2012》.pdf

《DIN EN 16261-3-2013 Pyrotechnic articles - Fireworks Category 4 - Part 3 Test methods German version EN 16261-3 2012《烟火制品 4类烟火 第3部分 试验方法 德文版本EN 16261-3-2012》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16261-3-2013 Pyrotechnic articles - Fireworks Category 4 - Part 3 Test methods German version EN 16261-3 2012《烟火制品 4类烟火 第3部分 试验方法 德文版本EN 16261-3-2012》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、March 2013 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、71.100.30!$-“1962910www.din.deDDIN EN 16261-3Pyrotechnic articles Fireworks, Category 4 Part 3: Test methods;English version EN 16261-3:2012,English translation of DIN EN 16261-3:2013-03Pyrotechnische Gegenstnde Feuerwerkskrper, Kategorie 4 Teil 3: Prfverfahren;Englische Fassung EN 16261-3:2012,Engl

3、ische bersetzung von DIN EN 16261-3:2013-03Articles pyrotechniques Artifices de divertissement, Catgorie 4 Partie 3: Mthodes dessai;Version anglaise EN 16261-3:2012,Traduction anglaise de DIN EN 16261-3:2013-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritati

4、ve.Document comprises 27 pages 02.13 DIN EN 16261-3:2013-03 2 A comma is used as the decimal marker. National foreword This document (EN 16261-3:2013) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic articles” (Secretariat: NEN, Netherlands). The responsible German body involved in i

5、ts preparation was the Normenausschuss Materialprfung (Materials Testing Standards Committee), Working Committee NA 062-08-81 AA Pyrotechnische Gegen-stnde. The Committee would like to bring attention to the fact that the following legal provisions are to be observed when applying DIN EN 16261-3 in

6、Germany: Gesetz ber explosionsgefhrliche Stoffe (Sprengstoffgesetz - SprengG) (German Explosives Act) of 10 September 2002 (BGBl. I, p. 3518), as amended by the Viertes Gesetz zur nderung des Sprengstoffgesetzes (Fourth Act Amending the Explosives Act) of 17 July 2009 (BGBl. I, p. 2062)1) Erste Vero

7、rdnung zum Sprengstoffgesetz (1. SprengV) (First Ordinance on the Explosives Act) of 31 January 1991 (BGBl. I, p. 169), as amended by the Viertes Gesetz zur nderung des Spreng-stoffgesetzes (Fourth Act Amending the Explosives Act) of 17 July 2009 (BGBl. I, p. 2062)1). 1)Registered in the DITR databa

8、se of DIN Software GmbH, obtainable from: Beuth Verlag GmbH, 10772 Berlin.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16261-3 December 2012 ICS 71.100.30 English Version Pyrotechnic articles - Fireworks, Category 4 - Part 3: Test methods Articles pyrotechniques - Artifices de divertissement

9、, Catgorie 4 - Partie 3: Mthodes dessai Pyrotechnische Gegenstnde - Feuerwerkskrper, Kategorie 4 - Teil 3: Prfverfahren This European Standard was approved by CEN on 20 July 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

10、 European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official ve

11、rsions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austri

12、a, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

13、 Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Memb

14、ers. Ref. No. EN 16261-3:2012: EEN 16261-3:2012 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Test environment for functioning test .5 4.1 General 5 4.2 Wind measurement 5 5 Apparatus .5 6 Test methods 9 6.1 Construction and stability 9 6.1.1 Outer di

15、mension of item .9 6.1.2 Determination of calibre . 10 6.1.3 Determination of gross mass 10 6.2 Design Verification 10 6.3 Determination of tube angle 10 6.3.1 Apparatus 10 6.3.2 Procedure 10 6.4 Angle of ascent and burst height 11 6.4.1 General . 11 6.4.2 Dimensions of mortar . 11 6.4.3 Support of

16、mortar . 11 6.5 Measurement of sound pressure level . 11 6.5.1 Apparatus 11 6.5.2 Procedure 11 6.6 Extinguishing of flames . 11 6.6.1 Apparatus 11 6.6.2 Procedure 11 6.7 Visual and audible inspections . 12 6.8 Mechanical conditioning 12 6.8.1 Apparatus 12 6.8.2 Procedure 12 6.9 Thermal conditioning

17、. 12 6.9.1 Apparatus 12 6.9.2 Procedure 12 6.10 Function test . 12 6.10.1 Apparatus 12 6.10.2 Procedure 13 6.10.3 Monitoring of effect, rising/bursting and drop height . 13 6.10.4 Monitoring of effect range and effect dimensions of aquatic fireworks . 13 6.11 Measuring of CE-marking 14 6.11.1 Appara

18、tus 14 6.11.2 Procedure 14 Annex A (informative) Mechanical Conditioning (Shock Apparatus) . 15 Annex B (informative) Procedures for calculation of heights . 18 Annex C (informative) Calculation method for safety-/protection distance . 22 Annex D (informative) Overview of essential safety requiremen

19、ts and corresponding clauses of all parts of EN 16261 . 23 DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 3 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2007/23/EC on the placing on the market of pyrotechnic articles 24 Bibliography 25

20、 DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 4 Foreword This document (EN 16261-3:2012) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic articles”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication o

21、f an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be h

22、eld responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of Directive 2007/23/EC on the placing on the market of pyrotechnic arti

23、cles. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. EN 16261 is divided into the following parts: EN 16261-1, Pyrotechnic articles Fireworks, category 4 Part 1: Terminology; EN 16261-2, Pyrotechnic articles Fireworks, category 4 Part 2:

24、Requirements; EN 16261-3, Pyrotechnic articles Fireworks, category 4 Part 3: Test methods; EN 16261-4, Pyrotechnic articles Fireworks, category 4 Part 4: Minimum labelling requirements and instructions for use. According to the CEN/CENELEC Internal Regulations, the national standards organizations o

25、f the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

26、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 5 1 Scope This European Standard specifies test methods for fireworks of category 4. 2 Normative references The following documents,

27、in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16261-1:2012, Pyrotechnic art

28、icles Fireworks, Category 4 Part 1: Terminology EN 16261-2:2013, Pyrotechnic articles Fireworks, Category 4 Part 2: Requirements EN 61672-1, Electroacoustics Sound level meters Part 1: Specifications (IEC 61672-1) ISO 3599, Vernier callipers reading to 0,1 and 0,05 mm 3 Terms and definitions For the

29、 purposes of this document, the terms and definitions given in EN 16261-1:2012 apply. 4 Test environment for functioning test 4.1 General A large unobstructed area, which shall be wide open. The measuring points shall be positioned appropriately for the type of measurement being carried out. For aqu

30、atic fireworks, a water test area shall be available for testing the resistance to moisture and functioning in the expected manner. 4.2 Wind measurement The wind speed at a height of 1,50 m above the ground shall be measured and recorded using a wind speed meter (see 5.5). No performance testing sha

31、ll be carried out if the wind speed exceeds 5,0 m/s. 5 Apparatus Any equivalent apparatus with the same accuracy or better may be used. 5.1 Timing device. Timing device, capable of being read to the nearest 0,1 s. 5.2 Calliper. Calliper, flat faced vernier calliper reading to 0,1 mm, conforming to I

32、SO 3599. 5.3 Ruler. Ruler, with a scale resolution of 1,0 mm or better. DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 6 5.4 Measuring tape. Measuring tape, with a scale resolution of 10 mm or better. 5.5 Wind speed meter. The wind speed meter should accurate to at least 0,5 m/s. 5.6 Balance. Balance, w

33、ith an accuracy of 0,01 g or better. 5.7 Temperature chamber. 5.7.1 Up to (50 2,5) C. 5.7.2 Up to (75 2,5) C. 5.8 Sound level meter. Sound level meter of class 1 conform to EN 61672-1 with a free-field microphone. 5.9 Shock apparatus. The apparatus shall provide a deceleration of 490 m/s2(-50/+100)

34、m/s2(when measured at the centre of an unloaded platform) and the shock impulse duration (time elapsed from the starting of the machines deceleration to the time in which the deceleration reaches its maximum value during each first shock pulse) shall be 2 ms 1 ms working at a frequency of 1 Hz 0,1 H

35、z. An example of an apparatus is shown in Annex A. 5.10 Devices for measuring heights. Heights shall be measured using universal surveying instruments (USI) such as theodolites, electronic spirit levels or video (visible and/or infrared) systems. Examples of measuring methods and the calculation of

36、the height are given in Annex B. 5.11 Goniometer. Goniometer reading to 1 or better. 5.12 Mortar. The rising height of shells depends particularly on the clearance of the shell in the mortar (ratio of the maximum cross section area of the shell (AShell) to the inner cross section area of the mortar

37、(Amortar), also designated as “Q“. Q is the ratio of the outer diameter of the shell (do,shell,including the fuse to the lifting charge) squared over the inner diameter of the mortar (di,mortar) squared. The outer diameter of the shell shall be measured horizontally at the place of largest diameter

38、including the fuse to the lifting charge. The following conditions shall be achieved: 98,09,0mortari,2shello,2mortarshell=ddAAQ DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 7 shello,2mortari,shello,21,102,1 ddd For calibre 100 mm, a wider tolerance can be accepted. The following conditions shall be ac

39、hieved: 98,083,0*100Q shello,2mortari,*shello,22,1(02,1 ddd Another determining factor influencing the rising height is the length of the mortar (lmortar) length from the mortar muzzle to the mortar ground. The dimensions of the mortar may also be determined from Figures 1, 2 and 3. Key X calibre of

40、 the shell (mm) Y internal diameter of the mortar (mm) Figure 1 Dimensions of the mortars for spherical shells Calibre above 100 mm DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 8 Key X calibre of the shell (mm) Y internal diameter of the mortar (mm) Figure 2 Dimensions of the mortars for spherical she

41、lls Calibre up to 100 mm DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 9 Key X calibre of the shell (mm) Y inside length of the mortar (mm) lmortar= 6 X dn+ 70 lmortar= 4 X dn+ 120 4 X dn+ 120 lmortar(mm) 6 X dn+ 70 dnnominal calibre Figure 3 Range of the mortar length for spherical shells 6 Test metho

42、ds NOTE Any equivalent method with the same sensitivity and the same accuracy or better might be used. 6.1 Construction and stability 6.1.1 Outer dimension of item 6.1.1.1 Apparatus Ruler (see 5.3). 6.1.1.2 Procedure Use the ruler to measure the outer dimensions of the tested article to the nearest

43、of 1,0 mm and record the results. DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 10 6.1.2 Determination of calibre 6.1.2.1 Apparatus Calliper (see 5.2). 6.1.2.2 Procedure Use the calliper (see 5.2) to measure the calibre of the tested article at least three times at different positions on the article an

44、d to the nearest of 0,1 mm and record the results. 6.1.3 Determination of gross mass Use the balance (see 5.6) to measure the gross mass of the tested article and record the results. 6.2 Design Verification Compare the actual article with the detailed manufacturers drawing. Observe and record any no

45、nconformity. 6.3 Determination of tube angle 6.3.1 Apparatus Goniometer (see 5.11). 6.3.2 Procedure For determination of the tube angle, dismantle the functioned article (if necessary) in such a way that the angle of the tube against the vertical can be measured with goniometer (see Figure 4) and re

46、cord the results. Key 1 base of firework 2 tube of mine, Roman candle or shot tube Figure 4 Determination of tube angle DIN EN 16261-3:2013-03 EN 16261-3:2012 (E) 11 6.4 Angle of ascent and burst height 6.4.1 General The fireworks shall be fired vertically (firing device at 90 2). The measurement of

47、 heights may be made according to one of the methods described in Annex B. 6.4.2 Dimensions of mortar For type and batch tests, defined standard mortars (5.12) shall be used. Tables for the standardised inside diameter and inside length are given in 5.12. When the height of a shell casing (excluding

48、 the lifting charge) is more than twice the calibre, for all shells with a calibre greater than 400 mm and for shells that are designed to be fired from a specific mortar, the mortar recommended by the manufacturer shall be used. 6.4.3 Support of mortar The mortar shall be supported in such a way that it is not displaced by the firing of the tested article. No deformable material shall be placed under the mortar. 6.5 Measurement of so