DIN EN 908-2009 Agricultural and forestry machinery - Reel machines for irrigation - Safety German version EN 908 1999+A1 2009《农林机械 卷盘式灌溉机 安全性 德文版本EN 908-1999+A1-2009》.pdf

《DIN EN 908-2009 Agricultural and forestry machinery - Reel machines for irrigation - Safety German version EN 908 1999+A1 2009《农林机械 卷盘式灌溉机 安全性 德文版本EN 908-1999+A1-2009》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 908-2009 Agricultural and forestry machinery - Reel machines for irrigation - Safety German version EN 908 1999+A1 2009《农林机械 卷盘式灌溉机 安全性 德文版本EN 908-1999+A1-2009》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、December 2009DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 65.060.35!$7v“1562083

2、www.din.deDDIN EN 908Agricultural and forestry machinery Reel machines for irrigation Safety (includes Amendment A1:2009)English version of DIN EN 908:2009-12Land- und Forstmaschinen Beregnungsmaschinen mit Schlauchtrommel Sicherheit (enthlt nderung A1:2009)Englische Fassung DIN EN 908:2009-12Supers

3、edesDIN EN 908:1999-06See start of validitywww.beuth.deDocument comprises pages18DIN EN 908:2009-12 Start of validity This standard takes effect on 1 December 2009. DIN EN 908:1999-06 may be used in parallel until 28 December 2009. National foreword This standard includes safety requirements. This s

4、tandard has been prepared by Technical Committee CEN/TC 144 “Tractors and machinery for agriculture and forestry” (Secretariat: AFNOR, France), Working Group WG 3 “Mobile machines and trailers”. The responsible German body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical

5、Engineering Standards Committee), Section Landtechnik. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN (and/or DKE) shall not be held responsible for identifying any or all such patent rights. Amendment of the European Machine

6、ry Directive has made it necessary to review the previously valid standard, EN 908:1999, in terms of the essential requirements of the new European Machinery Directive, 2006/42/EC. This standard contains specifications meeting the essential requirements set out in Annex I of the “Machinery Directive

7、”, Directive 98/37/EC, (valid until 28 December 2009) and the “revised Machinery Directive”, Directive 2006/42/EC, which takes effect on 29 December 2009, and which apply to irrigation machines that are either first placed on the market or commissioned within the EEA. This standard serves to facilit

8、ate proof of compliance with the essential requirements of the directives. Once this standard is cited in the Official Journal of the European Union, it is deemed a “harmonized” standard and thus, a manufacturer applying this standard may assume compliance with the requirements of the Machinery Dire

9、ctive (“presumption of conformity”). The European Standards referred to in clause 2 of this document have been published as the corresponding DIN EN Standards with the same number. This standard makes reference to documents which were valid as of the publication of the European standard. Since then,

10、 the standards EN 292-1:1991, EN 292-2:1991, EN 294:1992, EN 953:1997 and EN 1553:1999 have been withdrawn. EN 292-1:1991 has been superseded by EN ISO 12100-1:2003 and EN ISO 12100-1:2003/A1:2009, EN 292-2:1991 has been superseded by EN ISO 12100-2:2003 and EN ISO 12100-2:2003/A1:2009, EN 294:1992

11、has been superseded by EN ISO 13857:2008, EN 953:1997 has been superseded by EN 953:1997+A1:2009 and EN ISO 1553:1999 has been superseded by EN ISO 4254-1:2005. Amendments This standard differs from DIN EN 908:1999-06 as follows: a) The designation of the machinery has been modified (6.2). b) Annex

12、ZA (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC” has been updated. c) Annex ZB (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC” has been included. Previous editi

13、ons DIN 11001-10: 1980-01 DIN EN 908: 1999-06 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 908:1999+A1 July 2009 ICS 65.060.35 Supersedes EN 908:1999English Version Agricultural and forestry machinery - Reel machines for irrigation - Safety Matriel agricole et forestier - Enrouleurs dirrig

14、ation - Scurit Land- und Forstmaschinen - Beregnungsmaschinen mit Schlauchtrommel - Sicherheit This European Standard was approved by CEN on 14 December 1998 and includes Amendment 1 approved by CEN on 23 May 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipu

15、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard

16、exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standar

17、ds bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingd

18、om. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 908:1999+A1:2009: EE

19、N 908:1999+A1:2009 (E) 2 Contents Page Foreword 3Introduction .41 Scope 42 Normative references 43 Definitions 54 Safety requirements and/or measures 64.1 General 64.2 Irrigation gun 64.3 Guiding system of hose 64.4 Spool .64.5 Stability .74.6 Orientation of the turret 74.7 Hydraulic lifting 74.8 Ac

20、cessories 74.9 Transport 75 Verification of safety requirements and/or measures 76 Information for use 86.1 Instruction handbook 86.2 Marking .8Annex A (normative) List of hazards 10Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/

21、37/EC“ 15Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 16DIN EN 908:2009-12 EN 908:1999+A1:2009 (E) 3 Foreword This document (EN 908:1999+A1:2009) has been prepared by Technical Committee CEN/TC 144 “Tractors and machin

22、ery for agriculture and forestry“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at

23、 the latest by January 2010. This document includes Amendment 1, approved by CEN on 2009-05-23. This European Standard supersedes EN 908:1999. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This European Standard has been prepared under a mandat

24、e given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ Annex A is normative and contains the “Lis

25、t of hazards“. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I

26、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DIN EN 908:2009-12 EN 908:1999+A1:2009 (E) 4 Introduction The extent to which hazards are covered is indicated in the scope of this

27、standard. These hazards are specific to reel machines for irrigation. The hazards that are common to all the agricultural machines (self-propelled, mounted, semi-mounted and trailed) will be dealt with in a standard currently in preparation (prEN 1553). 1 Scope This standard specifies safety require

28、ments and their verification for the design and construction of reel machines for irrigation including self-propelled machines. It describes methods for elimination or reduction of risks which need specific requirements for reel machines for irrigation. In addition, it specifies the type of informat

29、ion on safe working practices to be provided by the manufacturer. The list of significant hazards dealt with in this standard is given in annex A. Annex A also indicates the hazards which have not been dealt with. Environmental aspects have not been considered in this standard. This standard applies

30、 primarily to machines which are manufactured after the date of issue of the standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publ

31、ications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 292-1: 1

32、991, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology. EN 292-2:1991, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and specifications (and amendment A1:1995). EN 294:1992, Safety of machinery Sa

33、fety distances to prevent danger zones being reached by the upper limbs. EN 953:1997, Safety of machinery Guards General requirements for the design and construction of fixed and movable guards. prEN 1553:1998, Agricultural machinery Agricultural self-propelled, mounted, semi-mounted and trailed mac

34、hines Common safety requirements. DIN EN 908:2009-12 EN 908:1999+A1:2009 (E) 5 3 Definitions For the purpose of this standard, the definitions given in EN 292-1:1991 and EN 292-2:1991 apply together with the following: 3.1 reel machine type of traveller irrigation machine featuring a stationary stru

35、cture with a reel, coiling a hose which carries irrigation water to, and drags, a travelling cart, upon which is affixed the emitting system, which is most often an irrigation gun 3.2 irrigation gun large sprinkler used on reel machines and other systems NOTE The usual flow-rates from guns range fro

36、m 10 m3/h to 100 m3/h, and their nozzle diameter from 10 mm to 40 mm. 3.3 coiling one of the actions performed by the reel machine when irrigating: the reel machine is progressively coiling all the polyethylene hose on the drum, causing the irrigation gun to move regularly across the irrigation fiel

37、d. When the irrigation gun reaches the machine, the coiling is completed and the machine stops 3.4 guiding system lateral guiding device of the hose that permits its steady coiling with joined spirals 3.5 drive system of the guiding system mechanism providing power to the guiding system that ensures

38、 the even layering of the hose 3.6 sweeping zone envelope of the different positions of the turret corresponding to its different possible orientations 1 - Drum of the spool 2 - Turret 3 - Hose guiding system 4 - Irrigation gun Figure 1 DIN EN 908:2009-12 EN 908:1999+A1:2009 (E) 6 4 Safety requireme

39、nts and/or measures 4.1 General The reel machines for irrigation shall comply as appropriate with EN 292 for hazards which are not dealt with and especially with annex A of EN 292-2:1991/A1:1995 when EN 292 does not give precise requirements. Unless otherwise specified in this standard, the machine

40、shall comply with the requirements of prEN 1553:1998 and with tables 1, 3, 4 and 6 of EN 294:1992. 4.2 Irrigation gun The adjustment controls of the irrigation gun that have to be operated during the working (for example adjustment of the sector angle and of the rotation speed of the irrigation gun)

41、 shall be located at a distance less than 1,80 m from the ground or from the access platform, whatever the speed of rotation of the irrigation gun. Irrigation guns with a speed of rotation greater than 1 rad.s-1shall be located at a height equal to or more than 2 m from the ground or from any platfo

42、rm (vertical distance between the ground or the platform and the lowest rotating part of the irrigation gun). This requirement does not apply: when the swivelling range of the irrigation gun is restricted to a maximum of 300 provided that the adjustment platform be located outside the swivelling ran

43、ge; when the irrigation gun is fitted with a guard providing a safety distance in accordance with EN 294:1992. 4.3 Guiding system of hose When the coiling speed of the hose is greater than 0,4 m.s-1, access to crushing and shearing points between the hose and the guiding system and between the guidi

44、ng system and the frame of the machine shall be prevented by fixed guards according to EN 953 or by the framework of the machine using the safety distances according to table 1 of EN 294:1992. When the uncoiling speed of the hose can be greater than 0,4 m.s-1, access to crushing and shearing points

45、between the guiding system and the frame of the machine shall be prevented by fixed guards according to EN 953 or by the framework of the machine using the safety distances of table 1 of EN 294:1992. Access to the drive system of the guiding system shall be prevented by fixed guards according to EN

46、953. 4.4 Spool If the rotation of the drum generates crushing or shearing points between the spool and the machine frame, such points shall be guarded. Satisfactory methods include for example: a guard providing the safety distance according to tables 3 and 4 of EN 294:1992; or a full (without openi

47、ng) side wall without any prominent feature including the water delivery pipe between the axis of the drum and the hose. Machines equipped with hose speed selector shall be fitted with: DIN EN 908:2009-12 EN 908:1999+A1:2009 (E) 7 a device which allows for the removal of tension from the hose before

48、 changing gear; or a device which enables the operator to change gear under tension. 4.5 Stability Any means needed to ensure stability when working (e.g. jacks, supporting wheels) shall be an integral part of the machine. They shall comply with 4.3.2.1.1. of prEN 1553:1998. The machine shall be sta

49、ble when resting on a slope of 8,5 in the following conditions: without using the additional means to ensure stability; hoses full of water and with irrigation gun hooked; in all the directions of the turret around its vertical axis (if applicable); with the axle positioned parallel, then perpendicular to the slope. Any functional outlet of water, associated with the use of the machine, except the possible leakages, shall be at a minimum distance of 5 m away from the machine. 4.6 Orientati