DIN EN 622-4-2010 Fibreboards - Specifications - Part 4 Requirements for softboards German version EN 622-4 2009《纤维板 规范 第4部分 软质纤维板要求》.pdf

《DIN EN 622-4-2010 Fibreboards - Specifications - Part 4 Requirements for softboards German version EN 622-4 2009《纤维板 规范 第4部分 软质纤维板要求》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 622-4-2010 Fibreboards - Specifications - Part 4 Requirements for softboards German version EN 622-4 2009《纤维板 规范 第4部分 软质纤维板要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、March 2010 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 7

2、9.060.20!$a6“1621929www.din.deDDIN EN 622-4Fibreboards Specifications Part 4: Requirements for softboardsEnglish translation of DIN EN 622-4:2010-03Faserplatten Anforderungen Teil 4: Anforderungen an porse PlattenEnglische bersetzung von DIN EN 622-4:2010-03Panneaux de fibres Exigences Partie 4: Exi

3、gences pour panneaux tendresTraduction anglaise de DIN EN 622-4:2010-03SupersedesDIN EN 622-4:1997-08www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1203.10 DIN EN 622-4:2010-03 A comma is used as the decimal marker. National forew

4、ord This standard has been prepared by CEN/TC 112 “Wood-based panels” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Holzwirtschaft und Mbel (Timber and Furniture Standards Committee), Working Committee 042-02-15 AA Spiegelausschuss zu CE

5、N/TC 112 und ISO/TC 89 Holzwerkstoffe. Amendments This standard differs from DIN EN 622-4:1997-08 as follows: a) The additional thickness range 36 mm has been introduced. b) Marking requirements and definitions have been harmonized with EN 13986. Previous editions DIN 68750-1: 1952-04, 1958-04DIN EN

6、 622-4: 1997-08 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 622-4 November 2009 ICS 79.060.20 Supersedes EN 622-4:1997English Version Fibreboards Specifications Part 4: Requirements for softboards Panneaux de fibres Exigences Partie 4: Exigences pour panneaux tendres Faserplatten Anforder

7、ungen Teil 4: Anforderungen an porse Platten This European Standard was approved by CEN on 10 October 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterat

8、ion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by transl

9、ation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany,

10、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Mana

11、gement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 622-4:2009: EEN 622-4:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Requirement

12、s .54.1 General 54.2 Requirements for general purpose boards .64.2.1 Requirements for boards for use in dry conditions .64.2.2 Requirements for boards for use in humid conditions64.2.3 Requirements for boards for use in external conditions.64.3 Requirements for load-bearing boards .74.3.1 Requiremen

13、ts for boards for use in dry conditions .74.3.2 Requirements for boards for use in humid conditions75 Verification of compliance 75.1 General 75.2 External control 75.3 Factory production control .86 Marking .86.1 Boards marketed within the European Economic Area for construction applications86.2 Ot

14、her boards 86.3 Colour coding .8Bibliography . 10DIN EN 622-4:2010-03 EN 622-4:2009 (E) 3 Foreword This document (EN 622-4:2009) has been prepared by Technical Committee CEN/TC 112 “Wood-based panels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a nat

15、ional standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

16、ts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 622-4:1997. This European Standard is one of a series specifying requirements for fibreboards. The other part of this series are listed in Clause 2 and in the Bibliography.

17、 Compared with EN 622-4:1997 the following modifications have been made: a) additional thickness range 36 mm introduced; b) marking requirements and definitions adapted to EN 13986. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are

18、 bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swede

19、n, Switzerland and the United Kingdom. DIN EN 622-4:2010-03 EN 622-4:2009 (E) 4 1 Scope This European Standard specifies the requirements for softboards as defined in EN 316, with a density 230 kg/m3to 400 kg/m3. The values listed in this European Standard relate to product properties but they are n

20、ot characteristic values to be used in design calculations. NOTE Panels which are intended for use exclusively as thermal insulating products are covered by EN 13171. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated reference

21、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 310, Wood-based panels Determination of modulus of elasticity in bending and of bending strength EN 316, Wood fibre boards Definition, classification and sy

22、mbols EN 317, Particleboards and fibreboards Determination of swelling in thickness after immersion in water EN 326-1, Wood-based panels Sampling, cutting and inspection Part 1: Sampling and cutting of test pieces and expression of test results EN 326-2, Wood-based panels Sampling, cutting and inspe

23、ction Part 2: Quality control in the factory EN 326-3, Wood-based panels Sampling, cutting and inspection Part 3: Inspection of an isolated lot of panels EN 622-1, Fibreboards Specifications Part 1: General requirements EN 13986:2004, Wood-based panels for use in construction Characteristics, evalua

24、tion of conformity and marking 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13986:2004 and the following apply. 3.1 dry conditions conditions corresponding to service class 1 of EN 1995-1-1 which is characterised by a moisture content in the materi

25、al corresponding to a temperature of 20 C and a relative humidity of the surrounding air only exceeding 65 % for a few weeks per year NOTE Boards of this type are suitable for use only in hazard class 1 of EN 335-3. 3.2 humid conditions conditions corresponding to service class 2 of EN 1995-1-1 whic

26、h is characterised by a moisture content in the material corresponding to a temperature of 20 C and a relative humidity of the surrounding air only exceeding 85 % for a few weeks per year NOTE Boards of this type are suitable for use only in hazard classes 1 and 2 of EN 335-3. DIN EN 622-4:2010-03 E

27、N 622-4:2009 (E) 5 3.3 external conditions conditions corresponding to service class 3 of EN 1995-1-1 which is characterised by climatic conditions leading to higher moisture contents than in service class 2 NOTE Boards of this type are suitable for use only in hazard classes 1, 2 and 3 of EN 335-3.

28、 3.4 general purpose use all non-load-bearing applications NOTE e. g. fitments and underlays. 3.5 loading-bearing use use in a load-bearing construction, i.e. an organized assembly of connected parts designed to provide mechanical resistance and stability to the works. NOTE Also referred to as “stru

29、cture“. 3.6 load duration class class characterised by the effect of a constant load acting for a certain period of time in the life of the structure NOTE The load duration classes are defined in EN 1995-1-1 (see Table 1). Table 1 Load duration categories Load duration class Order of accumulated dur

30、ation of characteristic load Examples of loading Permanent more than 10 years self weight Long term 6 months to 10 years storage Medium term 1 week to 6 months imposed load Short term less than one week snow a , wind Instantaneous - accidental loadingaIn areas which have a heavy snow load for a prol

31、onged period of time, part of the load should be regarded as medium-term. 4 Requirements 4.1 General Softboards shall comply with the general requirements of EN 622-1 together with the relevant requirements set out in 4.2 and 4.3 of this standard. The requirements in the tables shall be met be 5 per

32、centile values (95 percentile values in the case of swelling in thickness), based on the mean test values for individual panels and calculated in accordance with EN 326-1. In the case of swelling in thickness, they shall be equal to or less than the values in the tables, and in the case of all other

33、 properties, they shall be equal to or greater than the values in the tables. The values in the tables for both bending strength and modulus of elasticity shall apply to test results obtained in any direction in the plane of the panel. With the exception of swelling in thickness, the values given in

34、 the tables are characterised by a moisture content in the material corresponding to a temperature of 20 C and a relative humidity of 65 %. The values DIN EN 622-4:2010-03 EN 622-4:2009 (E) 6 given for swelling in thickness are characterised by a moisture content in the material corresponding to a t

35、emperature of 20 C and a relative humidity of 65 % before the treatment (immersion in water). The moisture resistance of softboards for use in humid and external conditions (see Tables 3, 4 and 6) is reflected by the respective requirements for swelling in thickness after 2 h immersion in cold water

36、 (according to EN 317). This property as well as the improvement of mechanical resistance of boards use in instantaneous or short-term load-bearing situation is derived from the addition of a hydrophobic substance such as a petrochemical or a natural substance. 4.2 Requirements for general purpose b

37、oards 4.2.1 Requirements for boards for use in dry conditions Table 2 specifies the requirements for general purpose boards for use in dry conditions. Table 2 Requirements for general purpose boards for use in dry conditions (type SB) Property Test method Unit Ranges of nominal thickness (mm) 10 10

38、to 19 19 to 36 36 Swelling in thickness 2 h EN 317 % 10 10 10 10 Bending strength EN 310 N/mm20,9 0,8 0,8 0,7 4.2.2 Requirements for boards for use in humid conditions Table 3 specifies the requirements for general purpose boards for use in humid conditions. Table 3 Requirements for general purpose

39、boards for use in humid conditions (type SB.H) Property Test method Unit Ranges of nominal thickness (mm) 10 10 to 19 19 to 36 36 Swelling in thickness 2 h EN 317 % 7 7 7 7 Bending strength EN 310 N/mm21,1 1,0 0,8 0,8 4.2.3 Requirements for boards for use in external conditions Table 4 specifies the

40、 requirements for general purpose boards for use in external conditions. Table 4 Requirements for general purpose boards for use in exterior conditions (type SB.E) Property Test method Unit Ranges of nominal thickness (mm) 10 10 to 19 19 to 36 36 Swelling in thickness 2 h EN 317 % 6 6 6 6 Bending st

41、rength EN 310 N/mm21,2 1,1 0,9 0,8 DIN EN 622-4:2010-03 EN 622-4:2009 (E) 7 4.3 Requirements for load-bearing boards 4.3.1 Requirements for boards for use in dry conditions Table 5 specifies the requirements for load-bearing boards for use in dry conditions for instantaneous or short-term load durat

42、ion only. Table 5 Requirements for load-bearing for use in dry conditions (type SB.LS) Property Test method Unit Ranges of nominal thickness (mm) 10 10 to 19 19 to 36 36 Swelling in thickness 2 h EN 317 % 8 8 8 8 Bending strength EN 310 N/mm21,2 1,1 0,9 0,8 Modulus of elasticity in bending EN 310 N/

43、mm2140 130 100 80 If it is made known by the purchaser that the boards are intended for specific use in flooring, walls or roofing, the relevant performances standard also has to be consulted. This may result in additional requirements having to be complied with. 4.3.2 Requirements for boards for us

44、e in humid conditions Table 6 specifies the requirements for load-bearing boards for use in humid conditions for instantaneous or short-term load duration only. Table 6 Requirements for load-bearing boards for use in humid conditions (type SB.HLS) Property Test method Unit Ranges of nominal thicknes

45、s (mm) 10 10 to 19 19 to 36 36 Swelling in thickness 2 h EN 317 % 6 6 6 6 Bending strength EN 310 N/mm21,3 1,2 1,0 0,9 Modulus of elasticity in bending EN 310 N/mm2150 140 120 100 If it is made known by the purchaser that the boards are intended for specific use in flooring, walls or roofing, the re

46、levant performances standard also has to be consulted. This may result in additional requirements having to be complied with. 5 Verification of compliance 5.1 General Verification of compliance with this European Standard shall be carried out using the test methods listed in EN 622-1 and in Tables 2

47、, 3, 4, 5, and 6, as appropriated. 5.2 External control External control of the factory, if any, shall be carried out according to EN 326-2. The inspection of a consignment of panels shall be carried out according to EN 326-3. DIN EN 622-4:2010-03 EN 622-4:2009 (E) 8 5.3 Factory production control F

48、actory production control shall be carried out according to EN 326-2. The properties listed in Tables 2, 3, 4, 5, and 6 and in EN 622-1 shall be controlled, using intervals between tests not exceeding the intervals given in Table 7. Sampling shall be carried out at random. Alternative test methods and/or unconditioned test pieces may be used if a valid correlation to the specified test methods can be proven. The intervals between tests given in