DIN EN 581-1-2017 Outdoor furniture - Seating and tables for camping domestic and contract use - Part 1 General safety requirements German version EN 581-1 2017《室外家具 野营区、住宅区和商业区用桌椅.pdf

《DIN EN 581-1-2017 Outdoor furniture - Seating and tables for camping domestic and contract use - Part 1 General safety requirements German version EN 581-1 2017《室外家具 野营区、住宅区和商业区用桌椅.pdf》由会员分享，可在线阅读，更多相关《DIN EN 581-1-2017 Outdoor furniture - Seating and tables for camping domestic and contract use - Part 1 General safety requirements German version EN 581-1 2017《室外家具 野营区、住宅区和商业区用桌椅.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、July 2017 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.140; 97.200.30!%h?x“2692885www.di

2、n.deDIN EN 581-1Outdoor furniture Seating and tables for camping, domestic and contract use Part 1: General safety requirements;English version EN 5811:2017,English translation of DIN EN 581-1:2017-07Auenmbel Sitzmbel und Tische fr den Camping, Wohn und Objektbereich Teil 1: Allgemeine sicherheitste

3、chnische Anforderungen;Englische Fassung EN 5811:2017,Englische bersetzung von DIN EN 581-1:2017-07Mobilier dextrieur Siges et tables usage domestique, collectif et de camping Partie 1: Exigences gnrales de scurit;Version anglaise EN 5811:2017,Traduction anglaise de DIN EN 581-1:2017-07SupersedesDIN

4、 EN 5811:200605www.beuth.deDocument comprises 10 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.06.17DIN EN 581-1:2017-07 2 A comma is used as the decimal marker. Start of application The start of application of this standard

5、is 2017-07-01. National foreword This document (EN 581-1:2017) has been prepared by Technical Committee CEN/TC 207 “Furniture”, (Secretariat: UNI, Italy). The responsible German body involved in its preparation was DIN-Normenausschuss Holzwirtschaft und Mbel (DIN Standards Committee Timber and Furni

6、ture), Working Committee NA 042-05-04 AA “Requirements of outdoor furniture, Mirror Committee to CEN/TC 207/WG 4”. In Clause 5, this standard includes safety requirements within the meaning of the Produktsicherheitsgesetz (ProdSG) (German Product Safety Act). Where this standard has been identified

7、by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety

8、and Health), it is to be presumed that outdoor furniture and tables which comply with this standard fulfil the relevant health and safety requirements. Amendments This standard differs from DIN EN 581-1:2006-05 as follows: a) a clarification of the definitions (camping, domestic and contract use) ha

9、s been taken out of Annex B and put in Clause 3 (which replaces the former Annex B); b) test probes and test methods have been replaced; requirements for edges and corners have been modified to take into account accessible parts during use (accessible parts of seating and tables have been defined);

10、c) tubular components have been defined; requirements for gaps and holes have been removed; d) Annex B (informative) has been included as a rationale to explain the risks covered with the requirements in Clause 5. Previous editions DIN EN 581-1: 1997-08, 2006-05 EUROPEAN STANDARD NORME EUROPENNE EUR

11、OPISCHE NORM EN 581-1 March 2017 ICS 97.140; 97.200.30 Supersedes EN 581-1:2006English Version Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 1: General safety requirements Mobilier dextrieur - Siges et tables usage domestique, collectif et de camping - Partie 1

12、: Exigences gnrales de scurit Auenmbel - Sitzmbel und Tische fr den Camping-, Wohn- und Objektbereich - Teil 1: Allgemeine sicherheitstechnische Anforderungen This European Standard was approved by CEN on 9 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which

13、 stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Euro

14、pean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members ar

15、e the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro

16、mania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any f

17、orm and by any means reserved worldwide for CEN national Members. Ref. No. EN 581-1:2017 EEN 581-1:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Test probes 5 Figure 1 Measuring probes . 5 5 Safety requirements . 5 5.1 General 5 5.2 T

18、ubular components 5 5.3 Shear and squeeze points . 5 5.3.1 Shear and squeeze points when erecting, adjusting and folding away . 5 5.3.2 Shear and squeeze points under the influence of powered mechanisms . 5 5.3.3 Shear and squeeze points during use 6 6 Test report . 6 Annex A (informative) Schematic

19、 presentation of requirements and conditions concerning shear and squeeze points . 7 Figure A.1 Schematic presentation of requirements and conditions concerning shear and squeeze points 7 Annex B (informative) Rationale for injury of fingers 8 DIN EN 581-1:2017-07 EN 581-1:2017 (E) 3 European forewo

20、rd This document (EN 581-1:2017) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September

21、 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This do

22、cument supersedes EN 581-1:2006. Compared to EN 581-1:2006, the main modifications are: clarification of the definitions (camping, domestic and contract use) taken from Annex B and put in Clause 3 (so Annex B will be superseded), test method is deleted, edges and corners are modified to take into ac

23、count accessible part during use (accessible parts for seating and tables are defined), tubular components are defined, requirements for gaps and holes removed, addition of an Annex B (informative) as a rationale to explain the risks covered with requirements in Clause 5. According to the CEN-CENELE

24、C Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icel

25、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 581-1:2017-07 EN 581-1:2017 (E) 4 1 Scope This part of EN 581 specifies the general safety requirem

26、ents for outdoor seating and tables for camping, domestic and contract for use by adults, without regard to materials, design/construction or manufacturing processes. It does not apply to seating for spectator facilities. It does not include requirements for the durability of upholstery materials, c

27、astors, reclining and tilting mechanisms and seat height adjustment mechanisms. Mechanical safety requirements are covered by EN 581-2 for seating and EN 581-3 for tables. Annex A (informative) is a schematic presentation of requirements and conditions concerning shear and squeeze points. Annex B (i

28、nformative) is a rationale concerning fingers injury. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest e

29、dition of the referenced document (including any amendments) applies. EN 581-2:2015, Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 2: Mechanical safety requirements and test methods for seating EN 581-3:2007N1), Outdoor furniture - Seating and tables for campin

30、g, domestic and contract use - Part 3: Mechanical safety requirements and test methods for tables 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 automatic locking mechanism mechanism which engages without guidance by the user and prevents un

31、intended movement 3.2 shear and squeeze point shear and squeeze points exist if the distance between two accessible parts moving relative to each other can be more or equal than 7 mm and less or equal than 18 mm in any position during movement 3.3 outdoor furniture for contract use outdoor furniture

32、 intended for non-private use in places with public access 3.4 outdoor furniture for domestic use outdoor furniture intended for private use in places without public access 3.5 outdoor furniture for camping use outdoor furniture foldable or knock-down and light-weight, intended for use in connection

33、 with camping and travelling DIN EN 581-1:2017-07 N1)Nationalfootnote:Here, 2007isindicatedasyearof publication. However, the correct year of publication is 2017: EN 581-3:2017. _EN 581-1:2017 (E) 5 4 Test probes There shall be three cylindrical probes with diameters of 00,17+mm, 0,1012 +mm and 0,10

34、18 +mm with hemispherical ends, see Figure 1. Key 1 00,17+mm, 0,1012 +mm and 0,1018 +mm Figure 1 Measuring probes 5 Safety requirements 5.1 General In order to avoid physical injury when the product is in its intended position of use, all edges and corners shall be rounded, chamfered or otherwise pr

35、otected. This applies to: Seating: Edges of the seat, back rest and arm rests and any part of the bottom surface of the seat at a distance less than 120 mm from any edge, where a finger can commonly access; Tables: Table tops, any part of the underside of the top surface at a distance less than 500

36、mm from any edge below the table, where a knee and/or an arm can commonly access. All other parts shall be free from burrs, sharp edges and sharp points. Movable and adjustable parts shall be designed so that injuries and inadvertent operation are avoided. It shall not be possible for any load beari

37、ng part of the furniture to come loose unintentionally. All parts which are lubricated to assist sliding shall be designed to protect users from lubricant stains when in normal use. 5.2 Tubular components There shall be no accessible holes in the ends of tubular components with a diameter between 7

38、mm to 12 mm and with a depth more or equal to 10 mm. The bottom of tubular legs in contact with the floor shall be closed or capped, however, holes in them are allowed as long as they are not between 7 and 12 mm. These requirements shall be assessed using the test probes (Clause 4). 5.3 Shear and sq

39、ueeze points 5.3.1 Shear and squeeze points when erecting, adjusting and folding away Unless 5.3.2 or 5.3.3 are applicable, shear and squeeze points that are created only during erecting, adjusting or folding away are acceptable providing the user can be assumed to be in control of his/her movements

40、 and to be able to cease applying the force immediately on experiencing pain. 5.3.2 Shear and squeeze points under the influence of powered mechanisms There shall be no accessible shear and squeeze points created by parts of the furniture operated by powered mechanisms, e.g. mechanical springs and g

41、as lifts. This requirement shall be assessed using the test probes (Clause 4). DIN EN 581-1:2017-07 EN 581-1:2017 (E) 6 5.3.3 Shear and squeeze points during use There shall be no accessible shear and squeeze points created by loads applied during normal use. Shear and squeeze points are not accepta

42、ble if there is a risk of injury created by the weight of the user during normal movements and actions, e.g. attempting to move the seating by lifting the seat or by adjusting the backrest. This requirement shall be assessed using the test probes (Clause 4). For loungers, the loads applied during no

43、rmal use are the loads used for the following mechanical tests in Table 1 of EN 581-2:2015: Test 2: Additional seat and leg rest static load; Test 3: Seat and back durability; Test 4: Additional seat durability; Test 5: Durability on back rest mechanism. For other seating, the loads applied during n

44、ormal use are the loads used for the following mechanical tests in Table 2 of EN 581-2:2015: Test 2: Seat front edge static; Test 3: Combined seat and back durability; Test 4: Durability test on seating with a multi-position back. For tables, the loads applied during normal use are the loads used fo

45、r the following mechanical tests in Table 1 of EN 581-3:2007N2): Test 1: Vertical static load on main surface; Test 4: Vertical static load on ancillary surface; Test 5: Horizontal durability test. 6 Test report The test report shall include at least the following information: a) reference to this p

46、art of the European Standard (EN 581-1:2017); b) details of piece of furniture tested; c) any defects observed before testing; d) the test results according to the applicable clauses; e) compliance with the requirements; f) the name and address of the test facility; g) the date of test. DIN EN 581-1

47、:2017-07 N2) National footnote: Here, 2007 is indicated as year of publication. However, the correct year of publication is 2017: EN 581-3:2017. _EN 581-1:2017 (E) 7 Annex A (informative) Schematic presentation of requirements and conditions concerning shear and squeeze points Figure A.1 is a Schema

48、tic presentation of requirements and conditions concerning shear and squeeze points. Figure A.1 Schematic presentation of requirements and conditions concerning shear and squeeze points DIN EN 581-1:2017-07 EN 581-1:2017 (E) 8 Annex B (informative) Rationale for injury of fingers Clause Title Risk cover 5.1 General Risk of cutting a part of the users body when in contact with the product 5.2 Tubular components Finger entrapment in holes on tubular component and damage on floors 5.3 Shear and squeeze points Shearing and squeezing of fingers, thumbs excluded DIN EN 581-1:2017-07